坯塊 的英文怎麼說
中文拼音 [pīkuāi]
坯塊
英文
briquet-
That is, he had lain down where the ground fell sharply away below the triple belt of wire and shouted up at the rock and earth parapet.
那是說，他伏在三重鐵絲網下陡峭地朝下削的地方，抬頭朝著石塊和土坯壘成的胸墻大聲呼喊。This paper focuses on the core part of the il & sm fixture system - information process system ( ips ). after relevant information is obtained from the current part, ips designs the roughcast and the parameters of stuffing, matches or designs rational locating box, positions all the locating bolt, finishes the procedure of datum conversion and ensures the communications between state shaping system, part fixing system and nc programming system
本文的研究對象為il & sm夾具系統的核心部分? ?信息處理系統（ informationprocessingsystem ? ips ） ，它通過獲取零件的相關信息，進行毛坯與填料厚度的設計，設計或配置出合理的尋位箱，智能布置尋位元件，完成基準轉換，並負責與狀態成型系統、工件安裝系統、 nc編程系統等模塊的通訊。For the establishment of software environment, author analyzed its working process, and made key analysis for the handling of roughcasts. he not only have realized the direct generation of simple roughcasts. for the roughcasts that were drawn with autocad, he also made research about how to handle them in the virtual environment
對于軟體環境的建立，作者分析了其工作流程，並對其中的毛坯處理模塊作了重點分析，不但實現了簡單毛坯的直接生成，對于用autocad生成的毛坯與虛擬環境的對接技術也作了研究。Bean curd workshop was the family workshop in the past, it used manual pushing the grinder and block press, " tofu night, just before dawn to sell, " said one
過去豆腐坊都是以家庭為單位，居家當作坊，採用手工推磨旋漿，石塊壓坯，有「三更豆腐，五更賣」一說。The experimental data has been used to validate pdm and low temperature sintering mechanics. the advantage and disadvantage of pdm have been discussed also. for the first time, the pdm is used to study the low temperature sintering mechanics of uo _ 2, and the research results indicate : 1
3 、基於燒結頸長大速率與緻密化動力學方程得出，影響二氧化鈾低溫燒結的因素有原始粉末粒徑、粉末堆積方式、坯塊原始密度、燒結溫度、燒結時間、燒結氣氛等;粉末壓坯一定時，燒結溫度、燒結時間和燒結氣氛就成為控制低溫燒結的關鍵因素。Steel skeleton compact
鋼骨架坯塊Microstructure of the composite layer was analyzed with help of optical microscope, scanning electronic microscope ( sem ), electronic probe microanalysis ( epma ) and x - ray diffraction ( xrd ). the compacting of the billet and the forming mechanism of the carbide reinforcement were studied based on thermodynamics and kinetics of reaction, sintering theory and the result of dta. at the same time, the wear - resistance of the composite layer was studied under condition of dry sliding friction
利用光學顯微鏡、掃描電子顯微鏡、電子探針以及x -射線衍射儀，分析了表面復合層的基體組織結構；運用反應熱力學、動力學、粉末燒結理論和燃燒合成理論，結合差熱分析結果，探討了表面復合層壓坯的燒結緻密化原理和碳化物增強相的形成機理；利用坯塊在真空燒結爐不同溫度下的燒結出來的顯微組織分析，模擬出坯塊的燒結過程中的化學反應過程。The whole course of process design is separated into three parts as blank layout, characteristics checking and strip layout
在這一章里將介紹工藝設計子系統內的三個模塊：工藝性分析、毛坯排樣、條料排樣。Day 99 : the coach was just being tough on you because he can see your potential
教練之所以對你嚴格要求是因為他知道你很有潛力，是一塊好坯子Pdm is utilized to forecast the non - crystal phenomena in the sintering process and study the effect of non - crystal on the process of sintering
因此採用超化學計量uo _ （ 2 + x ）坯塊是實現低溫燒結的必要條件。Metallic powders ; determination of green strength by transverse rupture of rectangular compacts ; identical with iso 3995 : 1985
金屬粉末.用矩形粉末壓制坯塊的橫向斷裂測定壓坯強度The speed became fast at the temperature 1050. the reaction could carry completely when billets was kept in vacuum tube for 3 hours " at 1050 temperature, under the striking of great quantity of heat when the molten iron poured into the mold, the reaction was blazed rapidly and continued at a high speed. the diffusible speed of v and c was very fast because the billet was heated over 1300 in a moment, so the reaction ca n complete in a few minutes
（ 5 ）碳化反應v + c vc在900左右開始發生，此時是固相反應，反應速度較慢，反應不能進行完全，隨溫度升高，該碳化反應的速度加快，在1050保溫3小時可以進行完全，在鑄造燒結時在過熱鐵水的巨大熱流密度沖擊下， v + c vc立即被激發，並以很快的速度進行，由於坯塊被加熱到1300以上，此時c和v擴散速度很快，因此鑄造澆注后的幾四川大學碩士學位論文分鐘內反應可以進行完全。分享友人