塊體性能檢驗 的英文怎麼說

中文拼音 [kuāitǐxìngnéngjiǎnyàn]
塊體性能檢驗 英文
inspection for properties of masnory units
  • 塊 : 名詞（古時佩帶的玉器） penannular jade ring （worn as an ornament in ancient china）
  • 體 : 體構詞成分。
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 能 : 能名詞（姓氏） a surname
  • 檢 : Ⅰ動詞1 （查） check up; inspect; examine 2 （約束; 檢點） restrain oneself; be careful in one s c...
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 檢驗 : checkout; test; examine; inspect; verify; survey; check;checking;testing;[英國]jerque（指檢查船舶...
  1. Experiments are performed and results show : 1 the popular retrieval models the okapi s bm25 model and the smart s vector space model with length normalization do not perform well for document similarity search ; 2 the proposed model based on texttiling is effective and outperforms other models, including the cosine measure ; 3 the methods for the three components in the proposed model are validated to be appropriately employed

    我們通過實驗驗證了以下三點： 1 trec中的常用信息檢索模型不能很好地解決文檔相似搜索2我們提出的基於texttiling技術的模型是有效的，性能優于其他模型3我們提出的模型中所採用的方法是有效的，包括利用texttiling技術進行文本子主題分割，利用餘弦公式來計算文本塊之間的相似度，以及利用最優匹配方法來求解文檔之間的總體相似度。
  2. As the requirements of its function, a bus control interface board has already been designed. also the paper have provided the scenarios demonstration for the bus control interface board ( bcib ), the design for the protocol of communication, the hardware for bcib, the software for bcib, and the software for the processor ' s communication. while the analysis for the capability of real - time and the calibration and test for subsystem have been also finished. during the design, the system advanced ability, reliability, resources availability and the cost - efficency ratio are considered. the issus such as system integrated control, mutual exclusion of the shared storages, generation of handshaking signal and system self - test were resolved

    本論文主要對航空自衛系統的綜合化方式進行了深入研究，並按其功能等方面要求，對航空自衛系統綜合化總線通信模塊進行了設計，主要完成了總線通信模塊方案論證、通訊協議設計、總線通信模塊硬體設計、總線通信模塊（ bcib ）軟體設計、處理機通信軟體設計、實時性分析、系統調試、試驗等項工作，在設計過程中，綜合考慮了系統先進性、資源利用率、費效比及可靠性等因素；重點解決了系統綜合控制方式、共享存儲器互斥、握手信號產生及系統自檢測等問題。
  3. In this thesis, can bus is used as the system bus, concentrating the research on the feasibility of using redundancy can bus technology in large - scale motor vehicle safety performance detecting & control system. this thesis first gives an overall design of the data collection and control system applied to the front end of a large - scale motor vehicle safety performance detecting & control system. regarding that the bus controller, bus driver and bus transfer medium would fail to function easily, the dual mode cold - redundancy structure is adopted in system to ensure the reliability

    本文採用can總線作為系統總線，重點研究冗餘can總線技術應用於大型機動車安全性能測控系統的可行性並進行驗證:首先對基於冗餘can總線的機動車安全性能測控系統的前端數據採集與控制系統進行了總體設計，考慮到總線控制器、總線驅動器和總線介質都是容易出故障的部件，系統採用了二模冷冗餘結構來保障can總線通訊的可靠進行;其次，根據系統需要，設計了基於c8051f021的帶冗餘can總線通道的數據採集與控制模塊，用於採集與處理檢測現場的模擬信號和數字信號，並自行開發了can總線應用層協議以及應用軟體，通過冗餘can總線實現與上位機的可靠通訊;然後，為了驗證冗餘can總線設計方案的可行性，搭建試驗平臺並進行can總線故障切換的試驗;最後對課題的研究工作進行了總結與展望。
  4. The paper puts forward a kind of economical numerical control milling machine system which is supported by windows and industry pc that are acted as software and hardware platform on the base of analyzing the present development of economical numerical control system and some existent problem, and expatiates the system software ' s collectivity frame, also introduces detailedly form and operational way of the user ' s interface. besides, the thesis also frames and accomplishes each module such as syntax inspect module, translation module, tool compensation module and track interpolation module adopting visual c + + 6. 0 and the kind of facing object and modularized program design method by analyzing rationales and function of the software ' s modules, moreover presents the programmer ' s flow chart and parts of source code, whereafter validates arithmetic of translation and tool compensation by simulating process testing program

    本文在分析了我國經濟型數控系統的發展現狀以及目前存在的一些問題的基礎上，提出了一種以windows和工業pc機作為軟、硬體平臺的經濟型數控銑床系統，闡述了該系統軟體的總體結構，並對其用戶界面的組成及其操作過程做了較為詳細的介紹，分析了軟體的各個模塊的基本原理和功能，採用visualc + + 6 . 0以及面向對象、模塊化的程序設計方法，完成了語法檢查模塊、譯碼模塊、刀具補償模塊以及軌跡插補模塊的具體設計，並給出了程序設計流程圖和部分源代碼，通過系統的模擬程序模擬加工過程驗證了譯碼和刀補演算法的正確性。
  5. Inspection for properties of masnory units

    塊體性能檢驗48
分享友人
分享到 Line

分享到臉書