塑性彎曲 的英文怎麼說

中文拼音 [sùxìngwānqū]
塑性彎曲 英文
plastic bending
  • 塑 : 動詞（塑造） model; mould
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 彎 : Ⅰ形容詞（彎曲） curved; bent; crooked; flexuous; tortuous Ⅱ動詞1 （使彎曲） curved; bend; flex 2 ...
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  1. Severe plastic deformation ( spd ) processing, especially equal - channel angular processing ( ecap ) of steel and other iron - based alloys, has achieved increasing interest recently because of the potential for obtaining ultrafine grains and improving the properties

    近年來，強烈塑性變形特別是鋼和鐵基合金的等徑彎曲通道變形因為具有獲得超細晶組織和改善性能的潛力，引起了各國研究人員的很大興趣。
  2. The machine is applicable to the plasticity material to inhibit the craft, such as hurtles to press, curve, turn over the side, lamella to pull to stretch etc. craft, also can used for correct, pressing to pack, the emery wheel model, the cold crowded metals spare parts model, the plastics product and the powder product of inhibit and model craft

    本機器適用於可塑性材料的壓制工藝，如沖壓、彎曲、翻邊、薄板拉伸等工藝，也可用於校正、壓裝、砂輪成型，冷擠金屬零件成型、塑料製品及粉末製品的壓製成型工藝。
  3. Pressure that this series the machine still have the extensive and in general use, be applicable to the every kind of plastic to process with take shape, if wash to press, squeeze, flection, fold the side, rivet jointing, orthopedics etc. ; stalk the pressing of set spare parts pack ; the plastics and what powder product inhibits ; stalk with other is similar to the correcting of spare parts ; the pressing of zero parts packs, and the pulling of spare parts of small scaled plank form stretch, type, fall material, press to print various uses of etc

    本系列機器還具有廣泛的通用性，適用於各種塑性材料的壓力加工和成形，如沖壓、擠壓、彎曲、折邊、鉚接、整形等；軸套類零件的壓裝；塑料及粉末製品的壓制；軸類和其他類似零件的校正；零部件的壓裝，小型板形零件的拉伸、成型、落料、壓印等多種用途。
  4. The leads from the model are most easily made of plastic tubing, which has little tendency to kink or leak and has good bending qualities.

    做為從模型引出的導管以塑料管為最方便，用塑料管不會糾結和漏氣而且彎曲性能好。
  5. From the feature of the force and deformation of the tpih, 5 different elements are used to mesh the different zones of the tube, which are structural beam 3d elastic 4, structural pipe plastic straight 20, structural pipe elastic elbow 18, structural shell elastic 4 node 63 and contact 3d pt - to - surf 49 ; the contact problem is assumed to be flexible - to - flexible ; the temperature field is assumed to be body load. a mechanical model corresponding to reality has been established for numerical simulation. based on the above, the 3 - d fem numerical simulation of tpih has been carried out by using the ansys program

    針對加熱彎管過程的受力和變形特點，採用三維梁單元、三維塑性直管單元、三維彈性曲管單元、三維殼單元與三維點對面接觸單元等5種不同的單元分別對管毛坯不同區域進行劃分，並對接觸單元採用柔體-柔體的處理方法，將溫度場作為體載荷處理，建立了符合實際的加熱彎管問題數值模擬力學模型：在此基礎上，應用商用軟體ansys對加熱彎管過程進行三維有限元模擬與研究，獲得了成形時推力、彎矩、支撐力大小及其變化趨勢。
  6. Elasto plastic bending

    彈塑性彎曲
  7. Test method for flexural properties of glass fiber - reinforced plastics

    玻璃纖維增強塑料彎曲性能試驗方法
  8. The influence of such parameters as axial load index, aspect ratio and percentages of lateral reinforcement, on seismic performance of reinforced concrete frame column in hong kong and analyses the distribution relationships of flexural deformation, shear deformation and slippage of longitudinal reinforcement in joint zone

    根據試驗結果，討論了軸壓比、配箍率、剪跨比等參數對其抗震性能的影響，分析了水平荷載作用時塑性鉸區的彎曲變形、剪切變形和縱向鋼筋粘結滑移變形所產生的位移在框架柱總水平側移中所佔的比例及其變化規律。
  9. Test method for flexural properties

    拉擠玻璃纖維增強塑料桿彎曲性能試驗方法
  10. Test method for flexural properties of fiber reinforced pultruded plastic rods

    纖維增強拉擠塑料棒彎曲特性試驗方法
  11. A fem of elasto - plastic flexural - torsional buckling of steel members under cyclic loading

    循環荷載下壓彎鋼構件彈塑性彎扭屈曲的有限單元法
  12. Although strict design calculations are made to guarantee the members have sufficient strength in their work life, yet dash and improper loads may damage them during construction and in service. these damages include elastic - plastic bending and local dent in the walls of the tube. in addition, corrosive medium such as atmosphere and contaminated water can also bring corrosion damage in the walls of the tube

    雖然都經過嚴格的設計計算，以保證其在使用壽命期內有足夠的強度，但在安裝施工和使用期間，往往因受到沖撞和非正常荷載而產生彈塑性彎曲和凹陷等損傷，此外大氣、受污染的水分等腐蝕性介質也可能在管壁上產生腐蝕損傷。
  13. Elastic - plastic bending induced residual stress and its influence on tensile yield strength of plates

    彈塑性彎曲所致殘余應力及其對板料拉伸屈服強度的影響
  14. Though the strength of mc nylon gear is low than metal gear, for it has low abrasion and inertia as well as flexible, it may be directly taken the place of metal - especially non iron metal, cast iron and non quenching steel

    盡管mc尼輪的強度明顯比相應的金屬輪低，由於它的低摩擦性和低慣性，以及熱塑性塑料輪輪的彈性彎曲，在很多應用上可以直接替代金屬-尤其是非鐵金屬鑄鐵和未經淬硬處理的鋼材。
  15. In this paper, stress and strain are analyzed in elastic - plastic bending process of plate, and a viewpoint is put forward in with plastic stress and strain neutral layer displace toward inside, and coincide with elastic stress and strain neutral layer when big curvature elastic - plastic bending process is come into being of plate on the basis of the theory of plane curving pole in the material mechanics

    摘要通過對板料彈塑性彎曲應力應變分析，利用材料力學中的平面曲桿理論，提出了板料大麴率彈塑性彎曲塑性應力應變中性層和彈性應力應變中性層均向內移動並重合的觀點。
  16. Fibre - reinforced plastic composites - determination of flexural properties

    纖維增強塑料彎曲性能試驗方法
  17. Testing methods for flexural properties of carbon fiber reinforced plastics

    碳纖維增強塑料彎曲性能的測試方法
  18. Elastic - plastic bending

    彈塑性彎曲
  19. Test method for flexural properties of

    玻璃纖維增強塑料彎曲性能試驗方法
  20. Plastics - determination of flexural properties by use of small specimens

    塑料彎曲性能小試樣試驗方法
分享友人
分享到 Line

分享到臉書