塑性斷裂擴展 的英文怎麼說

中文拼音 [sùxìngduànlièkuòzhǎn]
塑性斷裂擴展 英文
propagation ductile fracture
  • 塑 : 動詞（塑造） model; mould
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 斷 : Ⅰ動詞1 （分成段） break; snap 2 （斷絕;隔斷） break off; cut off; stop 3 （戒除） give up; abstai...
  • 裂 : 裂動詞[方言] （東西的兩部分向兩旁分開） open
  • 擴 : 動詞（擴大） expand; enlarge; extend
  • 斷裂 : break; disrupt; flying off; fracture; fragmentation; out break; rift;crack;bursting;rupture;rendi...
  1. Author thinks that the direction of the maximum plastic distortion along a constant radius around the crack tip may be considered as the direction of shear - mode fracture ( named pmax - criterion ) and the load when located shear band prongs the ligament in the front of crack tip is regarded as the limited load of shear - mode fracture. ( 3 ) the fad ( fracture assessment diagram ) of titled crack is proposed based on achievements of mesomechanics about i - ii complex ductile fracture of metal, and the titled crack is classified two kinds : void - mode fracture is assessed by fracture assessment curve, and shear - mode fracture by limited load. ( 4 ) using a fe program based on plantle - ressue theory to calculate some mesomechanical parameters, a flange joint structure of a high pressure vessel ( design pressure 31. 4mpa and the thickness of the hemispherical head is half of that of shell. ) is analyzed to determine whether the structure under operation pressure is safe or not, forecast the mode of potential invalidation and argue for the rationality of design of the structure

    試件的整體斷裂為剪切型，但在試件芯部裂尖鈍化區中部出現了韌窩型啟裂並有一定的擴展，說明局部較高的應力三軸度也會使韌窩型機制得以發展，但是不改變試件整體的剪切型斷裂模式；對韌性斷裂的剪切模式的細觀機理做了一定的探討，並且提出了含裂紋構件剪切型斷裂的宏觀判據：認為裂紋前方的集中剪切帶中與裂紋尖端等半徑處最大有效塑性應變出現的方向可以作為裂紋剪切斷裂的方向（可簡稱為_ （ pmax ）準則） ，集中剪切滑移帶貫穿裂紋前方承載韌帶時的載荷可以作為極限載荷；本文運用金屬韌性斷裂細觀力學在一復合型韌性斷裂方面的研究成果，採用失效評定圖的形式，提出了傾斜裂紋的安全性評定方法的基本框架。
  2. Still, the change of vg parameter in the beam was investigated in this thesis. dilation of plastic belt in the beam is also studied. analysis show that there is clear direction during the dilation of plastic belt, which is similar with the path of shear - mode fracture

    分析表明塑性區的擴展有明顯方向性，據此得到的塑性區擴展方向與剪切型斷裂時的斷裂路徑比較接近，也與加載過程中韌帶區出現的集中剪切滑移線的方向比較一致。
  3. Tial - based alloys with high specific strength are the most potential high temperature structural materials for aerospace application. however, the application of these materials is hindered by low resistance of damage, low room - temperature ductility and fracture toughness and high crack growth rate

    Tial基合金比強度高，是最具潛力的航空、航天用高溫結構材料之一，但因其具有較低的抗損傷能力，較低的室溫塑性、斷裂韌性和高裂紋擴展速率，這些斷裂特性阻礙了這種材料的應用，因而仍有必要研究其斷裂機理。
分享友人
分享到 Line

分享到臉書