塑性流 的英文怎麼說

中文拼音 [sùxìngliú]
塑性流 英文
plastic flow
  • 塑 : 動詞（塑造） model; mould
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  1. The mechanisms summarized are as follows 1 ) compressional normal stress ; 2 ) ductile and / or viscous deformation in bedding fault since incompetent bed is susceptible to plastic flow ; 3 ) higher likelihood of clay / shale smearing ; 4 ) foliation fabric whose sealing capacity is enhanced greatly in direction perpendicular to foliation

    其機理可歸納為四個方面： 1 ）壓性的正應力； 2 ）以韌性及粘性變形為主，因為非能幹巖層易塑性流變； 3 ）塗抹效應強； 4 ）面理化組構，垂直面理方向的封閉能力大大增強。
  2. Based on sale method ( simplified ale, in which the mesh may move with arbitrarily prescribed velocity with respected to the fluid, and lagrange interfaces are maintained between cells containing different material. ), the line loop integral difference scheme is derived which can be used to calculate two - dimensional elastic - plastic flow

    並在sale （ simplifiedale ，一種簡化的ale方法，網格可以任意運動，但物質界面處的網格仍然以物質速度運動，物質界面始終為lagrange網格線以保證網格中只有單物質出現）方法框架下，推導並給出了適用於彈塑性流計算的ale線積分差分格式。
  3. Finite element analysis of casing damage in plastic flow formation

    塑性流動地層套管破壞的有限元分析
  4. Non - coaxial plastic flow theory in multi - dimensional stress state

    復雜應力狀態下巖土體的非共軸塑性流動理論
  5. The studies of material two - dimensional plastic flow in friction stir welding

    攪拌摩擦焊焊縫材料二維塑性流動研究
  6. Bingham plastic flow

    賓厄姆塑性流
  7. By using one - dimensional finite different hydrodynamic code coupled with four spall models, spall in ductile metal has been studied

    摘要在平面一維彈塑性流動有限差分計算程序中加入4種延性金屬層裂模型，對平板撞擊層裂實驗進行數值模擬。
  8. In addition, the constitutive models included in flac - 3d are deep into research, and th e stress increments are corrected in terms of the plastic strain increment while occurrence of plasticity flow

    此外，還對flac - 3d內嵌的本構模型深入研究，塑性流動發生時塑性應變增量對應力增量的修正。
  9. Frictional performances of sulphurized layers on carbon steel using plastic flown line theory

    用塑性流線理論對碳鋼滲硫表面摩擦特性的研究
  10. The thesis introduces the general engine development, domestic and foreign, analyses the present situation and future development trend of environment friendly lubricants, studies on theories of flow activation and low - temperature jellification which well illustrate the low - temperature property of environment friendly lubricants, researches the low - temperature flowability of environment friendly lubricants in perspective of molecule, then theoretically synthesizes plastic and flow principles of environment friendly lubricants and finally reaches a ground to explain low - temperature properties of environment friendly lubricants

    本文論述了國內外內燃機油的發展概況，分析了環境兼容潤滑油的發展現狀及趨勢，研究了可以用於解釋環境兼容潤滑油低溫性能的流動活化理論和低溫成膠理論，從分子的角度研究了環境兼容潤滑油低溫流變特性，對潤滑油的粘塑性流變機理進行了理論推導，找出了解釋環境兼容潤滑油低溫流變特性的根據。
  11. Through the simulation of the forming process, we can get the deformations, stress, strain, plastic flowing in sheets and the interface state under impact load and rolling load, the deformation of the sawtooth form and comparing to the initial state, the results above are expressed in computer animated way. and the effect of geometrical ( mainly different form, including 90 degree, isoceles triangle ， 75 degree, and 1. 5 high and wide ), material and technical parameters on the bond strength are analyzed, also including the comparison of different sawtooth form. the optimum parameters are got

    對雙金屬復合板成型過程進行模擬，從而得到在沖擊載荷和軋輥壓力作用下基板和覆板的應力、應變分佈和塑性流動變形規律，復合后的齒形的變形情況與初始齒形形成對比，以動畫的方式模擬成型過程，並分析了不同幾何參數（主要是不同的齒型，其中包括直角齒型、等腰齒型、 75度齒型、 1 . 5高寬齒型） 、材料參數、工藝參數對復合強度的影響，以及不同齒型的變形對比以及齒型對復合情況的影響，提出最優齒型、最優工藝參數，有效地指導了實驗。
  12. Paper aims at the theory problem of exact celerity machining design which is realized urgently in special shaped products, solves mathematics model of similar forming plastic stream, recurring to modern conformal mapping fruit, builds die mathematics model and optimized function equation of arc square product in precision extruding / drawing, establishes theory model for precision celerity shaped die of cad / cam integrative constitution

    摘要本文針對亟待實現的擠壓（拔制）異型材模具精密快速加工設計理論課題，藉助于近代共形映射理論研究成果，求解了異型材擠壓（拔制）模具相似成形塑性流動的數學模型，建立了圓角方型材精密擠壓（拔制）模具模腔數學模型及其優化函數方程，建立了為實現模腔精密快速的cad / cam一體化的理論模型。
  13. Sbs elastomers do not depend on a high shearing rate to achieve the injection viscosity, but sebs elastomers are vice - versa

    Sbs彈體無需依賴高剪切率來達至塑性流動力， sebs彈體卻需依賴高剪切率來達至塑性流動力
  14. This constitutive model describes the non - associated plastic flow of granular material, and replaces the assumption that granular material complies with associated flow rule in the limit " equilibrium theory of granular material

    該本構模型反映了散體材料的非相關塑性流動，取代了散體極限平衡理論中散體材料服從相關流動法則的假定。
  15. According to the analyses of the visco - elastic and visco - plastic rheological properties of grey silt - like soft soils in yingkou district, the author interpreted that tyey show different rheological proprties as time and stress level changed

    基於營口地區淤泥技粉質粘土的粘彈性及粘塑性流變特性，指出二者隨時間和應力水平的變化表現出不同的流變特性。
  16. Metal flow behavier in friction stir welding of lf6 aluminum alloy and ld10 aluminum alloy

    6攪拌摩擦焊的金屬塑性流動
  17. Emform423 contains special extreme pressure additives to extend dielife and promote smooth, even floe of metal and quick, clean release of parts from the dies

    Emform423含有特殊的極壓添加劑，可延長模具壽命；並能形成勻順的金屬塑性流動，從而使工件得以迅速、潔凈地自模具脫離。
  18. The famous project of gas transiting west to east and the cross - river tunnel of huangbu river in shanghai also will be constructed with this technique, which is under the plan. among the shield tunneling methods, up to now, earth pressure balanced shield tunneling ( epbs ) is the most universal type, and it is very certain that the epbs method adopt to our country increasingly. the key factor to success in epbs is converting the muck which is lack of fluidity excavated from the cutter face to the plasticity soil. but when the shied tunneling machine advancing, it is considerably difficult to reach this requirement because of the ground soil condition, which is consist of stiff clay, silt, weathered rock, and so on

    近些年來我國城市地鐵建設迅速發展，盾構施工法作為一種安全而又環保的施工方法得到了廣泛的使用，另外在黃浦過江隧道，西氣東輸的穿黃隧道等工程也在使用盾構隧道施工技術。這其中土壓平衡式盾構在我國的使用最為普遍，成為地鐵隧道施工技術的主流。土壓平衡式盾構施工成功的關鍵是要將開挖面切削下來的土體在壓力艙內調整成一種「塑性流動狀態」 。
  19. The afterflow represents a production of kinetic energy which becomes convered into a pressure wave when the outward flow of water is reversed.

    殘余塑性流動代表在外向水流返回時動能變為壓力波的一種結果。
  20. Rheological model and equation of viscoelastic - plasticity of paste - like backfill pulp

    似膏體粘彈塑性流變模型與流變方程研究
分享友人
分享到 Line

分享到臉書