塑性結持度 的英文怎麼說
中文拼音 [sùxìngjiēchídù]
塑性結持度
英文
plastic consistency-
The hemicelluloses and pectic substances interact with the cellulose microfibrils of the cell wall to give extra strength and at the same time retain some plasticity
半纖維素和果膠質與細胞壁中的纖維素微纖絲相結合，這樣就具有了較大的強度同時還可以保持一定的可塑性。Based upon virtual displacement method and the updated - lagrangian approach, stiffness matrices for two - dimensional elastic - plastic beam model in large displacement were proposed, in the derivation of which transverse stress was included because it was believed that part of the 2nd order effects of various stresses, which are in equilibrium with each other and with the external loads, will counteract each other and neglecting either part would possibly lead to incorrect results
利用虛位移原理和更新的拉格朗日方法，導出了大位移彈塑性梁單元剛度矩陣的顯式表達式，在剛度矩陣推導中引入了截面內非線性剪應力和橫向應力的影響，剛度矩陣通過了剛體檢驗。之所以要引入橫向應力的影響，是因為本文認為，保持平衡所需的所有應力，它們各自的二階效應會相互抵消，因此忽略其中的任何一項都可能導致不正確的結果。During the temperature fields, the results indicate that the processing parameters such as the extrusion velocity, casting temperature, perform preheating temperature, die preheating temperature and so on are important for the temperature fields besides the dwell time. they are must be in concordance each other to the deforming zone is in the quasi - solid state, and the stable semi - solid extrusion is implemented. during the deforming fields, the hyperbolic sine thermo - rigid - viscoplastic fem model is selected according to the forming feature of the process, and the variations of the stress - strain fields are studied
在溫度場的模擬中，模擬結果表明，保壓時間是影響製件成形質量的關鍵因素之一，擠壓速度、液態金屬澆注溫度、預制體預熱溫度和模具預熱溫度等工藝參數對溫度場的影響也很大，需進行參數之間的協調，只有當變形區內部始終維持準固態時，才能實現穩定的液-固擠壓成形過程；在變形場的模擬中，根據液態浸滲擠壓的成形特徵，選用了雙曲正弦剛-粘塑性有限元計算模型，研究了變形過程中應力應變場的變化規律，研究了模角對變形和金屬流動的影響及變形力的變化過程和其影響因素。The results show that small cr addition in steel can decrease the lamellar spacing of pearlite, and markedly increase strength and hardness with almost the same ductility and toughness, and accordingly improve wear and shelling - resistance of wheel steel
實驗結果顯示，加入微量的鉻，可以細化珠光體的片層間距，在保持韌塑性基本不變的情況下，顯著增加材料的強度和硬度，從而提高車輪鋼的耐磨性和抗剝離性能。To ensure the safety of the dam and provide the technology for the decision during the process of construction and store water. in this article, the elastic - plastic stress - deformation of dam is calculated and the consolidation is analyzed. including the rock - fill dam, the stress and deformation distribution of cut - off wall, the deformation of sloping core, the incresment and subduction of pore water pressure and the effective stress situation calculation
為確保大壩安全，並為大壩施工期和蓄水期運行決策提供必要的技術支持，本論文根據上壩土料的應力一應變一強度特性、滲透和固結等特性，對壩體進行了彈塑性應力變形計算和固結分析，包括大壩堆石體、防滲墻的應力及變形分佈和斜心墻的變形、孔隙水壓力增長及消散和有效應力狀態計算等。The pore air pressure gradually goes up with the developing of axial strain in the process of the dynamic torsional shear test of loess, but the pore water pressure hold the line or goes up a little in the last. the stress - strain dynamic constitutive relationship of intact loess and man - made loess show the hyperbolic model. there are some remarkable differences of strength and strain between unsaturated loess and saturated loess
研究結果表明：非飽和黃土在動力扭剪試驗過程中，隨著軸向變形的發展，孔隙氣壓力逐漸上升，而孔隙水壓力則基本保持不變或後期略有升高；原狀黃土和重塑黃土的應力應變本構關系呈雙曲線型；非飽和黃土和飽和黃土的強度及變形特性存在明顯差異；進而分析了含水量、固結應力和固結應力比對黃土動力特性的影響本文最後對非飽和土的有效應力計算公式進行了討論。分享友人