壁附面層 的英文怎麼說

中文拼音 [bìbùmiàncéng]
壁附面層 英文
wall layer
  • 壁 : 名詞1 （墻） wall （of a house etc ） : 銅墻鐵壁 bastion of iron2 （作用像圍墻的部分） wall of st...
  • 附 : Ⅰ動詞1 （附帶） attach; add; enclose 2 （靠近） get close to; be near 3 （依從; 依附） agree to; ...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 層 : i 量詞1 （用於重疊、積累的東西 如樓層、階層、地層） storey; tier; stratum 2 （用於可以分項分步的...
  1. Inasmuch as the contoured walls are usually overcorrected for their own boundary layer, the flow in the planes parallel to the flat walls diverges.

    只要曲壁附面層的修正通常是超過需要量的，平行於平壁的平面上流動就發散。
  2. According to the feature that deformation resulted from water absorption and mildew appear mainly on the rabbet surface of ccf, this paper adopts rsst to spray a special waterproof sealant on rabbet surface of ccf, so that the sealant can get into fiberboard to certain extent by means of capillarity and penetration, blockage the holes between fibers and capillary, cut up passage of water and change the properties of soakage and sorption to water in capillarity and fiber. at the same time, solidified sealant can form a compact waterproof pellicle on rabbet surface so as to prevent water and humidity from fiber ' s expansion and mildewing

    針對吸水變形、霉變主要發生在地板企口表面的特徵，採用企口表面全封閉法，在復合強化地板企口表面噴塗特殊的防水封閉劑，使其依靠毛細管作用及滲透作用進入板內一定深度，堵塞木纖維之間的空隙及毛細孔通道，截斷水分傳遞的渠道，並改變毛細孔壁及纖維的表面性質以不利於水的浸潤與吸附，同時其固化后能在企口表面形成一層緻密的憎水薄膜，防止水分、濕氣從企口侵入板內引起木纖維膨脹變形、發霉等現象。
  3. Introduction to general ideas in air pollution control, air pollution effects, design of wall collection devices （ gravity settlers, centrifugal separators, electrostatic precipitators ）, design of dividing collection devices （ surface filters, depth filters, scrubbers for particulate control ）, design of controlling by concentration and recovery （ condensation, adsorption, absorption ）, design of controlling by oxidation （ combustion, biological oxidation, biofiltration ） and the choosing of a control technology

    本課程介紹空氣污染防制概念，空氣污染之影響，壁式集塵設備之設計（重力沉降室、離心分離器、靜電集塵器） ，分隔集塵設備之設計（表面過濾器、深層過濾器、洗滌器） ，以濃縮回收之控制設計（冷凝、吸附、吸收） ，以氧化之控制設計（燃燒、生物氧化、生物過濾） ，以及控制技術之選擇。
  4. The vortex simulated in this article include the shedding vortex induced by the vane trailing edge boundary layer, the endwall vortex generated by the endwall boundary layer interaction, the passage vortex generated by the rotor rotation, and the leakage vortex generated by the tip clearance flow

    渦輪級內的渦運動包括：導向器葉片尾緣附而層引起的脫落渦；轉子通道內轉子的旋轉運動產生的通道渦；根腳區兩個端壁附面層干涉，形成的根腳渦；存在葉尖漏流時，出現的漏流渦。
  5. The technology, which is developed on the basis of perfora ting techniques for oil wells and cement injection techniques, can not shoot thr ough the frozen pipe wall at predetermined ground location using energy - gatheri ng - blasting techniques, but also consolidate shaft wall rock by cement injectio n and filling along the frozen pipe and perforated hole s trajectories, achievi ng leakageproof of shaft walls and reducing vertically - added force

    它利用聚能射孔爆破技術，在預定地層位置將凍結管射穿，同時在地面利用凍結管及射孔彈道對特定地層進行注漿充填加固，既可實現井壁堵漏，又能減少由於地層沉降對井壁的垂直附加力。
  6. In this paper, the contrast experiments and theoretical researches on frosting and defrosting on low - energy surface and common metal surface are carried out simultaneously. low - energy surface restrains the frosting of air cooler, and the adhesion work of unit - area frost on low - energy surface is smaller than that on common metal surface, so pneumatic defrosting becomes easier

    本文還對低能表面與普通金屬表面的結霜、除霜進行了對比實驗和理論研究：低能表面不僅能有效地抑制蒸發器的結霜，而且單位面積霜層粘附功w _ ~ *比普通令屬壁面小，因而氣動除霜更容易。
  7. Results indicate that the characteristics of cavity flowfield were altered similarly by gas and liquid injection. the local boundary layer or shear layer are modified by injection on upstream / bottom wall of cavity, and the cavity shear layer immediately becomes angled with respect to the main flow direction. the injection on fore wall of cavity has little effect on the characteristics of cavity flowfield

    結果表明:氣體/液體噴流對凹腔整體流動特徵的影響是一致的，凹腔上游/底壁噴流破壞了當地附面層或剪切層，導致凹腔剪切層偏向主流方向;凹腔前壁噴注對凹腔流場特徵基本無影響。
  8. The other occurs in lower location near to wall, which is interpreted as viscous instability and has growth rate similar to primary disturbance

    該模態的增長率比基頻及其諧波要大的多。另一個模態位於附面層的近壁處，屬于粘性不穩定。
分享友人
分享到 Line

分享到臉書