壓制強度 的英文怎麼說

中文拼音 [yāzhìqiángdù]
壓制強度 英文
press strength
  • 壓 : 壓構詞成分。
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 強 : 強形容詞（強硬不屈;固執） stubborn; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  1. By optimizing the parameters such as the additive quantity of corn straw fibre, the content of amylum, the dosage of vesicant, the selecting of accessorial material, and the temperature of frothing, the cushion packaging material that has decompounding capability was prepared, and the factors influencing the mechanical strength of this material was analyzed by the method of static compress test

    通過對玉米秸稈纖維添加量、澱粉含量、發泡劑用量、輔料選擇、發泡溫度等參數的優化，實驗制備了具有可降解性能的緩沖包裝材料，並利用靜態壓縮實驗方法對該材料力學強度的影響因素進行了分析。
  2. To meet the processing requirements before sintering, the pressed briquet was pre - calcined at 1150 to make it possess adequate processing strength at first and then was shaped through precise turning on the numerical control lathe according to the design diagram of the femoral head prostheses of partial hip joint

    為滿足燒結前坯體加工的要求，壓制后的坯體在1150預燒，使其具備一定的加工強度，然後按照半髖關節股骨頭假體的形狀尺寸設計圖在數控車床上進行精密車削成型。
  3. In the paper, the diabase fiber was also selected to reinforce pvc for the first time, which has high intensity, high rigidity and low cost, the diabase fiber was treated firstly, then during mixing, melting, pressing procedure, the diabase / pvc composite were prepared

    本文首次對高強度、高剛度、低成本的輝綠巖纖維增強pvc復合材料進行了研究。論文首先對輝綠巖纖維進行了表面改性，然後將改性后的輝綠巖纖維與pvc混煉、壓片制備了輝綠巖纖維pvc復合材料。
  4. Series of guowei dry - method composite machines as new product are explored with our many years ' experience, the requirement of the users. the first metal of this machine is adopted with : photo - ecectricity auto. tracking " correcting deviation equipment, magnetic powder tension control. pneumatic back pressure shifting blade, oven temperature controlled qutomatically, big roll with oil heating, coating composite pneumatic control as well as double frequency governor etc. it will make the machine with fast speed, lower voice, low polluted by air, shout consumptionfor energy, stable working etc. especially suitable for al - foil with smooth surface and no enough firming, glass paper, polyester ect. the composite material with hard strength, fireproof, anti - ventilation, anti - fatty, frozen, dudrable steam etc character. it is widely used in food, pharmacy, as well as daily articles to package

    「國偉」 、系列乾式復合機，是我廠根據多年的復合機製造經驗及結合客戶需求，開發的新產品，該機第一基材採用了「光電自動跟蹤」糾偏放卷裝置，磁粉張力控制、氣動背壓移動式刮刀、烘箱溫度分段自動控制、大輥筒導熱油加熱、上膠復合氣動控制及雙變頻調速技術，使該機具有復合速度快、噪聲低、空氣污染小、能耗低、運行平穩等特點，適宜於表面光滑的鋁箔玻璃紙聚酰胺等與聚乙烯、聚丙烯等薄膜的復合，復合薄膜具有強度高、防水、防透氣、防油脂、可冷凍、蒸煮等優點，廣泛應用冷凍食品、乾燥食品、醫藥品及日用品的包裝。
  5. The magnetostriction of bonded tb03dy07fe2 rod composites is 580x 10 " 6 at a field of 200 ka / m, and the magneto - mechanical coupling coefficient is 0. 40 at a bias field of 118 ka / m

    相對而言制備工藝參數對合金的電阻率和抗壓強度影響較小，其電阻率等於熔煉法制備的材料的電阻率的10000倍左右，抗壓強度約為150mpa 。
  6. Based on the terszige and biot theory, initially analyze the economical of this experiment, directly save investment 22 % after compute. after that, computing the settlement of highway foundation, comparing the computing and survey value, the predict formula of vacuum - heaped load combining precompression for designing, this formula show that the distortion law of consolidation progress. at the same time, based on the position and room experiment, analyzes the intension transformation in soft soil and criteria of stabilization control

    在太沙基和比奧固結理論的基礎上，先分析了此次試驗的經濟性，經核算直接節約投資22 ，經濟效益十分明顯；隨后對真空堆載聯合預壓法加固軟土路基的沉降量進行了估算，並與實測值作對比分析，得出了真空堆載聯合預壓下的沉降量估算公式，能反映「真空」加固過程的變化規律；同時根據現場和室內試驗，分析了軟土強度的變化，以及給出並驗證了工后沉降控制標準。
  7. The important meaning in which this direction studied has lain in establishing the connection between the material science of concrete and civil engineering, analyse the strength in terms of material microcosmic or the mesoscopic, have important meaning to understanding, know the essential law of the strength of concrete. this text divides six chapters altogether. chapter one reviewed the pore structure in nowadays domestic and international research current situation, including the concrete examines research, research of the pore structure model and the research current situations of pore structure and strength relation of the pore method, have introduced some most important achievements of structure research of pore ; chapter two narrated much yardstick of the material mesoscopic structure of concrete and principle of examining pore technology of material of concrete, and the commonly used sign parameter in discussedding the pore and material pore of quito of cement and analyse, have explained that the influence factor of mip to the result of study of pore, has pointed out the limitation in mip in the pore structure ; analyse porosity and strength relation development course of model emphatically, and has carried on comparative analysis to the existing model, has pointed out the weak point of the original model ; on the basis of " ing integrate synthetically ", propose concrete pore structure compound body model and pore physical model of systemlex body ; chapter five carried on the corresponding test data to compares to the model parameter appearing in model of chapter four with and analyses, have received k value of the characteristic of strength of matrices of reflecting according to the method to return to analysis, and calculate the influence produced on the strength of concrete in revision that can probed into the content of cement, elastic mould and surface energy, exactness of the inspection model ; chapter six is the conclusion, according to studying the survey this text to some research conclusions of the pore structure and making corresponding prospect to the structure development of pore

    第一章回顧了孔結構在當今國內外的研究現狀，包括混凝土測孔方法的研究、孔結構模型的研究及孔結構與強度關系的研究現狀，介紹了孔結構研究方面的一些最重要的成果；第二章敘述了混凝土材料細觀結構的多尺度性及混凝土材料測孔技術的原理，並討論了水泥基多孔材料孔隙分析中常用的表徵參數，也說明了壓汞法測孔對研究結果的影響因素，指出了壓汞法在孔結構研究中的局限性；第三章是著重分析了孔隙率與強度關系模型的發展歷程，並對已有的模型進行了比較分析，指出了原有模型的不足之處；第四章在「綜合集成」的基礎上，提出了混凝土孔結構復合體模型和孔系統的物理模型，並模擬了該模型下由各單體並聯形成的復合體的斷裂過程，最後根據所建模型編制了相應的計算程序，可根據輸入的孔徑分佈與水泥含量等參數，實現混凝土理論強度的計算；第五章對第四章模型中出現的模型參數進行了相應的試驗數據對比分析，根據回歸分析的方法得到了反映基體強度特徵的k值，並從理論上探討了水泥含量、彈性模量和表面能的修正對混凝土強度計算產生的影響，檢驗模型的正確性；第六章是結論與展望，根據研究綜述了本文對孔結構的一些研究結論並對孔結構發展作了相應的展望。
  8. The high - strenght wearable complex pipeline is based on teel pipes, to the inner wall of which the high - strength wearable material ( patent no. zl02295132. 4 ) is pressed by means of mechanical strength which makes the material and pipe an organic unity. these pipes are joined together with flange joints to convey different kinds of medium under various conditions

    高強耐磨復合管道是以鋼管作為基體，通過機械壓制方式，使內層高強度耐磨材料（專利： zl02295132 . 4 ）與鋼管有機地結合為一體，利用法蘭式連接成不同形式的管道，可適用於不同條件和介質的輸送。
  9. Methods of test for production control of concrete - method of rapid test for compressive strength of concrete by warm water curing

    混凝土生產控制試驗方法.熱水養護法測定混凝土壓縮強度的快速試驗方法
  10. For a class of series - wound active power line conditioner the design approach law of a new fuzzy integral sliding mode variable structure control is presented. this method adjusts power electronic switch in order to achieve anticipated balance volt, finally makes active power line conditioner not only possess good robustness of variable - structure control and decrease vibration to the most but also increase the steady state precision. series - wound aplc adopted this control method possesses good dynamic and steady state performance

    針對串聯型有源電網調節器運用變結構控制策略，調節電力電子開關模式，以獲得預期的平衡電壓，對串聯型有源電網調節器提出了模糊積分變結構控制方法，使串聯型有源電網調節器既保持了常規滑模控制強魯棒性的優點，又減弱了滑模控制的抖振，提高了系統的穩態精度，使系統具有良好的動態和靜態性能，模擬試驗表明該控制策略是一種十分有效的控制方法。
  11. The results show that pva - dfrccs can lighter the concrete, develop the compression / flexural / tensile splitting strength and flexural toughness, decrease the deformation of both dry shrinkage and autogeneous shrinkage and decrease the permeability of chloride ion. experimental results reveal as well that attapulgite can improve significantly properties of interface and optimize properties of dfrccs

    研究結果表明這種新材料能夠減輕材料自重，增進材料的抗壓、抗折、劈裂抗拉和抗彎強度，較好地抑制纖維材料中的乾燥收縮和自收縮現象，提高纖維材料的氯離子抗滲性。
  12. The influence of burning system on the properties and structure of the ceramic capacitors has been studied under the certain temperature system, the optimum sintering temperature of the ceramics was primarily decided by the content of bi2o3 ? 3tio2. the sintering temperature dropped with the adding of bi2o3 ? 3tio2. at the range of suitable sintering temperature, slow heating and low temperature sintering can obtain fine grain and dense structure. it results in the improving of the breakdown voltage for the middle - high voltage ceramic capacitors

    研究了燒成工藝制度對電容器陶瓷性能和結構的影響，結果表明：在一定的升溫保溫時間下，瓷料的最佳燒結溫度主要取決于組成中bi _ 2o _ 3 ? 3tio _ 2的含量， bi _ 2o _ 3 ? 3tio _ 2含量的增加將降低燒結溫度；在合理的燒結溫度范圍內，慢速升溫和低溫燒結將有利於得到細晶緻密結構，從而改善中高壓陶瓷電容器的耐壓強度。
  13. Liupanshui beer co. ltd. has retrieved from bankruptcy to rapid development depending on technical innovation and improvement as follows : strengthening the control of saccharifying boiling intensity, the age of fermenting beer, filtration time, bottle washing of remnant alkali, sterilization intensity, and pressure prepare in nitrogen filling etc. ; making full play of employee ' s initiative and installing new equipments ; making control of filtration beginning time and keeping stable beer storage time at 0 ; settling the problem of beer species by high concentration dilution method ; applying low - pressure boiling system to increase boiling intensity, shorten boiling time, and increase beer non - biologic stability ; and making innovation of fermentation techniques to increase beer quality etc

    摘要六盤水啤酒有限責任公司依靠科技創新、走科技進步之路，通過加強對生產過程的糖化煮沸強度、發酵酒齡、開濾時間、洗瓶殘堿、殺菌強度、灌裝氮氣背壓等方面的控制；發揮人的主觀能動性，實施增加硬體設施；控制開濾時間，穩定控制0貯酒時間；利用高濃稀釋解決品種矛盾；採用低壓煮沸系統，提高煮沸強度、縮短煮沸時間，提高啤酒的非生物穩定性；改進發酵工藝，提高產品質量等措施，使企業實現了發展。
  14. By using 5000kn pressure - bent testing machine, the specimens of boulder concrete and crushed stone concrete were tested through three - point - bending method and wedge - split tensile method, the scale division of the index dial of pressure - bent testing machine is larger, whereas the predicted test - load is lesser, so the velocity of exerted load is controlled through observing the reading of the multimeter which is connected with the collecting systerm in order to continuously exert test - load

    本文使用5000kn壓彎實驗機，對不同強度等級的卵石混凝土和碎石混凝土試件分別進行了三點彎曲試驗和楔入劈拉試驗。試驗過程中，由於實驗機噸位較大，而試驗荷載預計較小，為了能夠有效地控制加載大小和加載速度，採用通過觀察與荷載傳感器相連的萬用表讀數控制加載速度的方法，連續加載。
  15. Methods of sampling and test for carbonaceous materials used in aluminium manufacture - cold ramming pastes - determination of the cold crushing strength of baked rammed paste

    制鋁工業用炭素材料取樣和試驗方法.第4部分:冷搗糊塊.第9節:熱搗糊塊冷壓碎強度測定
  16. Secondly, the effect of transverse deforming on the property of the wedge pressing was studied. the results showed that : the wedge pressing stock with the transverse deforming amount of 10 % acquired the best performance. the highest density got the biggest rate of slope while with the amount of 30 % the curve was more some special structure and performance as following : the large porosities was crushed into small or linear ones with the high - direction deformation amount of 20 % ; as the increasing of the high - direction deforming, the particles got a further deforming, the porosities got a further crushing, the small porosities were mergered by the large ones and the former then disappeared ; when the amound reached 60 %, the quantity of the porosities would obviously decrease which made the materials compact, the microstructure more uniform and the density and hardness curves more horizontal, the relative desity could reach 99. 7 %, the tensile strength b of the as - compacted samples reached 408mpa with the yield strength s teached 289mpa and the elongation percentage reached 13. 6 %. in addition, the microstructure of the wedge pressing stock under the pressing temperectureof 450 was uniform, the porosities and the boundries of the grains basically disappeared and the conjunction between particles was great

    採用雙向楔形壓制，大尺寸噴射沉積5a06鋁合金楔壓坯的組織和性能變化具有如下特點:當高向變形量為20 %時，大的孔洞變形破碎為小的孔洞，或呈線狀孔;隨著高向變形量的增加，顆粒進一步變形，孔洞進一步破碎，大孔「吞併」小孔，小孔塌陷並逐步消失;當高向變形量達到60 %時，孔洞量大為減少，材料基本緻密，組織趨于均勻，楔壓坯料的密度、硬度變化曲線接近水平線，坯料的相對密度達99 . 7 % ，抗拉強度_ b = 408mpa ，屈服強度_ （ 0 . 2 ） = 289mpa ，延伸率= 13 . 6 % ;對比其它的壓制溫度，在450楔形壓制的坯料組織均勻，孔洞及顆粒邊界基本消失，顆粒之間冶金結合良好。
  17. Metallic powders ; determination of green strength by transverse rupture of rectangular compacts ; identical with iso 3995 : 1985

    金屬粉末.用矩形粉末壓制坯塊的橫向斷裂測定壓坯強度
  18. Therefore, interlayer toughened composites are the excellent candidate materials for primary structure of aircrafts. in this paper, composites modified with particle - interlayer were fabricated. based on the aims of improving compression strength after impact ( cai ) and evaluate damage resistance and damage tolerance, mode ii fracture toughness test and quasi - static indentation test ( qsi ) were conducted

    本文採用層間顆粒增韌技術制備試驗件，基於提高沖擊后壓縮強度（ cai ）和考察損傷阻抗、損傷容限的目的，試驗測試了型層間斷裂韌性g _ （ c ） 、準靜壓痕（ qsi ）試驗的分層起始能量和接觸力?凹坑深度關系。
  19. Based on the fem model of the dam - reservoir system, the influence of water compressibility to the hydrodynamics is systemically analyzed and researched. it is showed thaf the water compressibility has significant effect to the size and distributing of hydrodynamics on the high dam, and the absorbency of reservoir bottom has a role as a damper on the dam - reservoir system

    基於庫水體各類邊界條件的有限元模型，系統分析了可壓縮性對壩體動力響應的影響，表明水可壓縮性對高壩動水壓力強度和分佈具有顯著影響，而庫底邊界條件對大壩的地震反應有抑制作用。
  20. The technique can avoid produce ti / al chemical compound in high temperature. the chemical compound would increase the difficulty of pressing. the research on vacuum degassing and temperature of pressing can acquire the ideal composite powders of highly

    對ti / al復合粉進行真空脫氣及低溫熱壓制可以降低坯料中空氣含量並提高粉末顆粒的界面結合強度，同時避免高溫下生成tial基化合物增加緻密難度，對真空脫氣及壓制溫度進行研究，獲得理想的緻密度極高的復合粉末。
分享友人
分享到 Line

分享到臉書