定子電路 的英文怎麼說

中文拼音 [dìngzidiànlù]
定子電路 英文
stator circuit
  • 定 : Ⅰ形容詞1 （平靜; 穩定） calm; stable 2 （已經確定的; 不改變的） fixed; settled; established Ⅱ動詞...
  • 子 : 子Ⅰ名詞1 （兒子） son 2 （人的通稱） person 3 （古代特指有學問的男人） ancient title of respect f...
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 路 : 1 （道路） road; way; path 2 （路程） journey; distance 3 （途徑; 門路） way; means 4 （條理） se...
  • 電路 : [訊] circuit （ckt）; electric circuit; electrocircuit電路板 circuit board; 電路保持 guard of a c...
  1. In the sub block circuit design, the contents that the author had introduced include : the principle of band gap voltage reference and the design technique in low power supply ; the analysis of spike pulse noise rejection, frequency divider and dead time in oscillator and control circuit ; the selection of the width and length ratio of four switches and 2x / 1x mode change point in driver and mode selection circuits

    在子電路設計中，作者比較深入分析的內容有:基準電路的原理及低電源電壓下基準電路的設計;振蕩器和控制電路中尖峰脈沖噪聲抑制、兩分頻電路及死區時間設定;驅動及模式選擇電路中開關管的寬長比的選擇及模式轉換點的設計。
  2. The sampling rate of the system can reach 3704 sps, and the crank angle is 1. 94 degree per sampling point corresponding to the crank speed of 1200r / min. in the mean time, the position signal of the piston could be collected by photo - electricity switch

    本研究首先設計和實現了摩擦力採集電子電路系統，裝置最大采樣率可達到3704sps ，在曲軸轉速為1200r / min時，對應曲柄轉角1 . 94度采樣點，並且可以採集用來確定活塞位置的光電開關的信號。
  3. The simulation results are all in accordance with the theory analysis, some even better than the theoretical specification. the basic principle of discrete pulse frequency modulation on step - up dc / dc converter is testified, and this effort accumulates more experience to design

    在完成電路原理分析與電路設計的基礎之上，應用eda軟體hspice對各個子電路模塊和整體電路進行了功能模擬及量化模擬，模擬結果均達到或優于預定指標。
  4. During the circuit design, the author analyzed the basic principle of the direct current motor, pwm control, h - bridge power driver, and two control techniques of h - bridge power drive circuit, designed its general structure, so the feasibility of the design is confirmed. then, reference, oscillator, power dmos gate drive circuit ( charge pump, bootstrap ), and dead time generation circuit are designed and analyzed in the sub - circuits. a current - controlled oscillator is presented in this thesis

    在電路設計中，作者介紹了直流電機的工作原理和數學模型、脈寬調制（ pwm ）控制原理、 h橋電路基本原理和h橋功率驅動電路的兩種控制模式，設計了驅動電路的總體結構，給出了電路的功能模塊，確定了設計的可行性，然後在子電路模塊中，重點分析設計了基準源電路、振蕩器電路、高端功率管柵驅動電路（電荷泵及自舉電路） 、低端功率管柵驅動電路和死區時間產生電路。
  5. In the paper, a speed estimator based on artificial neural network is designed according to the principle of direct torque control, the speed estimator is optimized by genetic algorithm, and the parameters of pid speed adjuster is also optimized by genetic algorithm. a stator linkage and torque observer based on stator resistance estimator using fuzzy neural network is also designed. eventually, the intelligent control of direct torque control system is implemented

    本文根據異步電動機直接轉矩控制原理，在應用人工神經網路進行速度辨識的基礎上，利用遺傳演算法對神經網路速度辨識器進行了優化設計；運用遺傳演算法對pid速度調節器的結構和參數進行了整合；在採用模糊神經網路對電機定子電阻辨識的基礎上，進行了定子磁鏈及轉矩的觀測，為最終實現無速度傳感器直接轉矩控制系統的智能控制創造了條件。
  6. Aim at the dtc ' s blemish mentioned above and the direction of dtc technique development, the dissertation put great emphasis on the work as follows, with an eye to exalt dtc system function : ( 1 ) a new speed - flux observer of an induction motor is proposed to enhance the accuracy of flux observing, which is an adaptive closed - loop flux observer and different from the traditions. a new adaptive speed - observation - way is deduced out according to the popov ' s stability theories ; ( 2 ) to improve the performance of dtc at low speed operation, we have to exalt the accuracy of the stator flux estimation and a new way of bp neural network based on extended pidbp algorithm is given to estimate and tune the stator resistance of an induction motor to increase the accuracy of the stator flux estimation ; ( 3 ) digital signal processor is adopted to realize digital control. an device of direct torque control system is designed for experiment using tms320lf2407 chip produced by ti company ; ( 4 ) bring up a distributed direct torque control system based on sercos bus, sercos stand for serial real time communication system agreement which is most in keeping with synchronous with moderate motor control ; ( 5 ) the basic design frame of the hardware and software of the whole control system is given here and some concrete problem in the experiments is described here in detail

    針對上面提到的直接轉矩控制的缺陷和未來直接轉矩控制技術發展方向，本論文重點做了以下幾個方面的工作，目的在於提高dtc系統的綜合性能： （ 1 ）提出一種新型的速度磁鏈觀測器，新型的速度磁鏈觀測器採用自適應閉環磁鏈觀測器代替傳統的積分器從而提高磁鏈觀測的精度，並且根據popov超穩定性理論推導出轉速的新型自適應收斂律； （ 2 ）改善系統的低速運行性能，主要從提高低速時對定子磁鏈的估計精度入手，提出了一種提高定子磁鏈觀測精度的新思路? ?利用基於bp網路增廣pidbp學習演算法來實時在線地修正定子電阻參數； （ 3 ）採用數字信號處理器dsp實現系統全數字化硬體控制，結合ti公司生產的tms320lf2407晶元，設計了直接轉矩控制系統的實驗裝置； （ 4 ）提出了基於sercos總線網路化分散式的直接轉矩控制系統， sercos （ serialrealtimecommunicationsystem ）是目前最適合同步和協調控制的串列實時通信協議； （ 5 ）基本勾勒出整個控制系統的硬體和軟體設計基本框架，詳細描述一些實驗中的具體的細節問題。
  7. Power electronic circuits can show rich nonlinear phenomena, such as bifurcations, chaos and etc. therefore chaotic dynamics is needed to analyze these phenomena

    電力電子電路在一定條件下會表現出豐富的非線性現象，例如混沌、分叉等，因此十分有必要把混沌動力學引入這一領域。
  8. With the elevation of the power factor, stator electric current decrease obviously and its range is about 20 %. so voltage loss and electric power wastage decrease effectively on electromotor power supply circuitry consequently

    隨著功率因數的提高，定子電流明顯的減小，減小幅度在20左右，從而有效地減少電動機供電線路的電壓損失及電力損耗。
  9. In this topic, the error characteristic of resistance voltage sensor was analyzed in theory, by using electric circuit analysis, the reasons which affected its error were gotten. based on theory analyses, initial structure was designed. then by using fem ( finite element method ) of simple resonance field, several structures electromagnetic field was calculated, and their amplitude errors, phase errors, maximum of electric field intensity and frequency characteristic of amplitude error were contrasted

    本文從理論上分析了電阻式電壓傳感器的誤差，用電路分析法定性的研究了影響電阻分壓器誤差的因素；在理論分析的基礎上進行了電阻分壓器結構的初步設計；基於該設計，利用簡諧場的有限元方法進行了場的計算，比較了幾種結構方案的幅值誤差、相角誤差、最大場強值及其幅值誤差的頻率特性，從而得到一種最優方案；製作了分壓器樣機，並在本實驗室進行了實驗；最後，對電子電路部分進行了初步設計，並提出了抗干擾的措施。
  10. After studying a lot of documents, we present a speed - estimating method for direct torque control system. this method is based on the theory of dtc, but it takes advantage of the convenient of both the theory of dtc and the theory of foc. we need only to sample the stator ' s current to estimate the speed of the rotor, at the same time the integration of the voltage is avoided

    在研究大量文獻的基礎上提出了一種適用於交流電機dtc控制系統的轉速計算方法，該方法以dtc控制為中心，結合dtc和定子磁場定向和轉子磁場定向各自的特點，綜合利用各自的有利之處，只需測量定子電流，避免了對電壓積分，思路清晰，計算簡單。
  11. Y. r. yang, c. l. chen, " steady - state analysis and simulation of a bjt self - oscillating zvs - cv ballast driven by a saturable transformer, " ieee trans. industrial electronics, vol. 46, no. 2, pp. 249 - 260, april 1999

    楊岳儒，陳秋麟，林昌賢「自激串振式半橋型電子安定器電路分析」工研院能資所電力電子技術雙月刊，第24期，第45 - 53頁， 1994年12月。
  12. This thesis is a production of circuit principles and simulation practice. based on the circuit principle analysis, the author simulated the sub - block circuits and the whole

    作者在電路原理分析的基礎之上，運用hspice模擬軟體對子電路模塊和整體電路進行了功能和性能參數的模擬驗證，模擬結果均達到或優于預定指標，證實了理論分析的正確性。
  13. At light loads, the architecture allows the chip to “ skip ” cycles to reduce power dissipation. in the circuit design, the basic principle and small signal model of the boost power stage are given at first, and then the stability and small signal model of the control loop are also analyzed, finally, the whole chip architecture and sub - block parameters are presented according to the application requirements

    在電路設計中，首先闡述了升壓型直流轉換器的功率輸出級的拓撲結構、基本原理、小信號模型，然後分析了電流模式控制迴路的穩定性及小信號模型，最後根據應用要求進行了電路的總體架構設計，完成了每個子電路的各種參數的分析、計算。
  14. Base on the boost principle analysis and circuit design in the beginning, the author simulated the sub - block circuits and whole chip circuit by applying eda tools hspice, the simulation result indicates that the ic has achieved the expectation of the function target and the electrical characteristics. although there were unavoidable disadvantages of this project, it is a worthwhile and valuable experience

    在完成電路原理分析與電路設計的基礎之上，作者應用eda軟體hspice對各個子電路模塊和整體電路進行了功能模擬及量化模擬，模擬結果均達到或優于預定指標，驗證了作者在第二章中闡述的直流升壓boost電路的設計理論，是設計理論與實踐相結合的一次有價值的嘗試。
  15. Adopting the electro - circuit control mode to ensure the long time of stably running

    採用電子電路的控制方式，保證了長時間的穩定運轉。
  16. The power circuit of the system adopts the voltage frequency conversion structure of ac - dc - ac, and is composed of the commutation circuit, filter circuit and intelligence power module ( pm15rsh120 ). control circuit takes the dsp chip tms320lf2407 as core, including the pwm signal occurrence circuit, detect circuit of stator current and direct current voltage of generatrix, drive circuit of intelligence power module, detect circuit of speed, protect circuit of system etc. all of this builds the full digital vector control system of asynchronous motor

    該系統的功率電路採用電壓型的交-直-交變壓變頻結構，由整流電路、濾波電路及智能功率模塊ipm （ pm15rsh120 ）逆變電路構成;控制電路以dsp晶元tms320lf2407為核心，加上pwm信號發生電路、定子電流檢測電路、直流母線電壓檢測電路、智能功率模塊驅動電路、速度檢測電路、系統保護電路等，構成了功能齊全的異步電機全數字化矢量控制系統。
  17. The mathematical model of multi - loop, which is improved through selecting new stator loops in this paper, can be used to simulate the transient behavior of external short circuit at machine ' s terminal and internal short circuit in the stator, not only under no - load condition with single machine but also under load condition connected to power network

    本文改進了原來的多迴路數學模型中對定子迴路的選擇，不僅可對同步發電機機端各種外部短路故障和單機空載下的各種定子內部故障進行暫態過程的模擬，還實現了負載時內部各種故障的暫態模擬。
  18. The problem of the strategical orientation of the country ' s electronic circuit module manufacturing enterprises is further presented next

    初步探討了我國電子電路模塊製造企業的定位問題。
  19. On dec. 13 - 15 the labor department, social assurance department, cpca profession appraisal station and cpca experts conducted audit to the three national profession standards

    十、 12月13日? 15日國家勞動和社會保障部和信息產業部在上海組織印製電路（電子電路）行業的專家，對印製電路（電子電路）製造業的三個國家職業標準進行了審定。
  20. Providing expertise service of ecp and gas to customers in compliance to safety, environmental regulations and internal rules ( ims )

    為客戶提供與電子電路板生產相關的氣體應用技術服務並遵從安全、環保及相關的公司規定。
分享友人
分享到 Line

分享到臉書