實用設計 的英文怎麼說

中文拼音 [shíyòngshèjì]
實用設計 英文
utility design
  • 實 : Ⅰ形容詞1 （內部完全填滿 沒有空隙） solid 2 （真實; 實在） true; real; honest Ⅱ名詞1 （實際; 事實...
  • 用 : Ⅰ動詞1 （使用） use; employ; apply 2 （多用於否定: 需要） need 3 （敬辭: 吃; 喝） eat; drink Ⅱ名...
  • 設 : Ⅰ動詞1 （設立; 布置） set up; establish; found 2 （籌劃） work out : 設計陷害 plot a frame up; fr...
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 設計 : devise; project; plan; design; excogitation; layout; layout work; styling
  1. Based on tests of nine 1 / 2 - scaled model slabs under vertical loads, the paper analyzed load - deformation curve and proposed limit value of height - width ratio under axial loads. 2. based on aseismic tests, the paper put forward a model of concrete frame, silica brick and a combination of the two, proposed that the silica brick works as a 45 compression bar, analyzed the factors which may influence bearing capacity of the slab and advised a formula including the numbers of bays and of storeys of the frame

    通過對墻板模型的抗震性能試驗研究，建立了由鋼筋混凝土框格、砌塊以及兩者協同作用三個部分組成的承載力極限狀態下的理論簡化計算模型；提出了墻板中填充塊等效斜壓桿寬度按45度計算的統一量化標準；分析了影響墻板承載力的主要影響因素，給出了表達墻板框格層數和跨數不同的斜截面承載力實用設計計算公式。
  2. Practical design method for large - diameter cast - in - situ piles with enlarged bases in wet - collapsing loess

    濕陷性黃土地區大直徑挖孔擴底灌注樁實用設計方法
  3. Through the investigation and theoretical analysis, a design method of deep - cutting loess slope in sanmenxia area is presented in this thesis

    為此，在工程調查和理論分析的基礎上，本文提出了三門峽地區深路塹黃土邊坡的實用設計方法。
  4. The originality of the thesis lies in : ( 1 ) establishment of analysis model for different design phases of multi - ribbed slab in accordance with the slab ' s grading and multimode failure mode, by felicitously assumption and affecting factor ' s evaluation, the computational model corresponding to codes " requirement is proposed

    （ 6 ） .實用設計方法的建立和完善通過中高層密肋壁板結構房屋的工程設計，結合其他結構體系的相關研究成果，初次建立了中高層密肋壁板結構房屋的概念設計原則和抗震計算方法。
  5. The analysis showed the strain of section is not plain under moment so that the moment is carried by force couple in the outer frame. 4. the paper gave the rigid frame - compression bar model for practical computation

    在試驗研究的基礎上，提出了密肋復合墻板實用設計的鋼架斜壓桿模型；通過線彈性有限元分析，就其優化設計進行了探討。
  6. Practical design of live fingerprint capturing set for police

    警用活體指紋採集儀的實用設計
  7. Practical design method for bolt end plate joints of light steel structure

    輕鋼結構螺栓端板連接的實用設計方法
  8. A great multi - purpose brush, ideal for dusting shimmer brick compact on cheekbones for a natural - looking, shimmery glow. can also be used with sheer finish powder, blush, or bronzing powder

    沾取所選擇的產品（珍珠光澤顏彩盤、腮紅餅、蜜粉、修容餅） ，輕?多餘的粉末，輕掃于所欲上色的部位。多用途的實用設計，可當成蜜粉或腮紅刷使用。
  9. On establishment of the mathematics model of water recycling system optimum planning in the high school

    二樁承臺實用設計方法的研究
  10. Finally, by simplifying the result of experiment, a practical design method about bearing capacity and deformation is got and can used by engineers

    最後，根據試驗研究結果進行簡化，提出組合板承載力和變形的實用設計方法，可供工程技術人員參考使用。
  11. With seismic loading tests on multi - rib composite walls and integer building models, this paper researches comprehensively on practical design methods for the structure of multi - rib panel, and provides the theoretical foundation for engineering application of this structure system

    本文結合密肋復合墻板力學性能試驗及整體房屋模型試驗，較全面分析研究了多層密肋壁板結構的實用設計方法，為該結構體系的工程應用奠定了理論基礎。
  12. Combined with test research and current code, the practical design methods of the tier structure of multi - rib panel are researched chiefly. basic principles in the process of structure conception design are achieved, practical computing formulas for rigidity and load - bearing of the structure of multi - rib panel are deduced, practical design methods and process for buildings in the structure are expatiated, and actual project is seismic calculated as an example in this paper

    提出結構概念設計應遵循的基本原則，包括結構體系的適用范圍，房屋層數及高寬比限值，建築平面及豎向布置要求；給出復合墻板的剛度及承載力實用計算公式，並與試驗值進行對比；闡述了多層密肋壁板結構房屋的實用設計方法及設計步驟，並將實際工程作為算例，進行了詳細抗震驗算。
  13. Practical design of soft foundation settlement forecast in expressway

    高速公路軟基沉降預測實用設計與研究
  14. One practical design method of soft foundation settlement forecast in expressway

    高速公路軟基沉降預測實用設計方法
  15. However, there is still a lot to be advanced. the paper, based on test and other available material, mainly studied on mechanical property and oblique section bearing capacity of the composite slab. 1

    本文是在對試驗和已有資料進行分析的基礎上，就密肋復合墻板的受力性能及斜截面承載能力實用設計方法進行了研究，完成了如下工作： 1
  16. On the basis of lucubrating in the design theory of air - cushioned belt conveyor, with the practice of engineering, in the case of an air - cushioned belt conveyor putted into production for export corn reconstruct project in ganjingzi quay company of dalian port, linked with long term practical experiences, the system and detail design of air - cushioned belt conveyor are completed

    在深入研究了氣墊帶式輸送機設計理論的基礎上，本文結合工程實際，以大連甘井子港務公司出口玉米改造工程投產的一臺氣墊帶式輸送機為例，結合多年來現場使用經驗，提出了氣墊帶式輸送機總體設計和關鍵的細部設計的實用設計方法。
  17. In this paper, for the sake of designing manufacturing logistics network structure, using reducing logistics general costs reducing logistics investment and enhancing client service level as optimization design of logistics network structure of manufacturing, on the base of analysis and forecast of manufacturing logistics capability and requirement, author provide corresponding mathematics models for the resolvent on choosing the number. location and scale of solid establishment. on the base of research above, the author also analyzes data information analysis instrument and applied mathematics method detailedly during the course of the design of enterprise logistics network structure, and gives integrated design process of logistics network structure of manufacturing

    本文主要的內容是以降低物流總成本，減少物流投資，提高客戶服務水平為製造企業物流網路結構設計與優化的戰略目標，在對企業的物流能力和物流需求進行分析和預測的基礎上，對企業物流網路結構設計，即物流固體設施的選址（主要是指使用的固體設施的數量、位置和規模）給出了對應于不同企業規模（不同數量）的物流設施的數學模型（在簡化假設條件情況下） ，並在此基礎上對企業物流網路結構的規劃具體過程中所需數據、信息、分析工具、實用設計方法進行詳細的分析，給出完整的企業物流網路結構設計的過程。
  18. The method which is common used of designing the isolation structure is based on the concept of " level - conversion intensity "

    在隔震結構的設計過程中，對上部結構的設計現有的實用設計方法是採用「水平換算烈度」的方法。
  19. Based on the experimental investigation and numerical analysis, the slab ' s shear and bending resistant expression is proposed and a representative wall ' s reliability index under small earthquake is figured out. sensitivity of every factors affecting shear strength is evaluated. the elastic stiffness and deformation of mrs and shear wall structure is compared

    （ 4 ） .密肋復合墻體承載力實用設計表達式的提出根據試驗結果和數值分析，建立了的密肋復合墻體抗剪和抗彎承載力表達式，並對其在地震作用下的可靠性進行了分析，得出了墻體的承載力可靠指標。
  20. Nowdays, external prestressing technique is used worldwidely and is developed continually. it is urgently necessary to probe into theoretics and practice actively, to deduce applicable design methods, accordingly to promote the application and development of external prestressing structures

    在體外預應力結構在世界各國廣泛運用和不斷發展的今天，迫切需要在理論和實踐方面的積極探索，簡化出方便工程應用的實用設計方法，從而推動體外預應力結構的應用和發展。
分享友人
分享到 Line

分享到臉書