導出包絡 的英文怎麼說

中文拼音 [dǎochūbāolào]
導出包絡 英文
derived envelope
  • 導 : 動詞1. （引導） lead; guide 2. （傳導） transmit; conduct 3. （開導） instruct; teach; give guidance to
  • 絡 : 絡構詞成分。
  • 導出 : leading-out; derive; derivation
  1. Proceed from the angle of enhancing the backing off grinding accuracy of the special shaped convex curved rake surface, and in accordance with the enveloping theory of differential geometry and the designing model of new configured carbide gear shaper cutters, the mathematical model for backing - off and grinding the special shaped convex curved rake surface of the new configured gear shaper cutters was derived

    從提高新構形硬質合金插齒刀異形凸曲前刀面鏟磨精度的角度出發，根據微分幾何的包絡理論及新構形硬質合金插齒刀設計模型，推導出鏟磨新構形插齒刀異形凸曲前刀面的數學模型。
  2. The thesis is based on income question, forest coverage rate and grop production. to beging with, date envelopment analysis is proved that it can be applicated into grain for green in shan - bei district, and then in view of the fact, seven esential factors which have influence on the project are found out : expense of dam, expense of crop, expense of cash tree, expense of defense tree, other economic crop, expense of grass and graziery ; and the output factors include : income of gdp, pure income per captia, the area of decreasing land loss, graziery income, crop production, income of tree, the totle income of economic crop. after the date of each facts are puted into dea model, unefficiencial decision making units ( dmu ) found. the data that are got through adjusting unefficiencial dmus dy dea can offer guide in shanbei district upgrading of an industrial structure. at the same time, taking into account some possible problems in or after grain for green in shan - bei district, the thesis bring out some propesal to improve the circ umstance, enhance the life level and put the relation of population, resource and circumstance into a healthy orbit

    因此，加快退耕還林還草，調整土地利用結構和產業結構，已成為實現山川秀美工程和可持續發展戰略的必經之路。論文以解決陜北地區的收入問題，植被問題以及糧食產量問題為出發點，首先從理論上分析了包絡分析方法在陜北地區退耕還林（草）中運用的可行性，然後結合陜北地區目前的實際情況，綜合分析出影響陜北地區退耕還林（草）的關鍵的七個因素作為輸入指標：水利水保設施投入，農作物投入，經濟林種支出，防護林支出，其它經濟作物，草類支出，畜牧業投入；以退耕還林所要解決的最終問題作為輸出指標： gdp收入、農民人均純收入、水土流失減少量、牧業總產值、糧食產量、林業總產值、其他經濟作物總產值。將各指標所對應的數據代入模型后，通過分析求解得出非有效的決策單元，再運用包絡分析方法的一些基本原理對非有效的決策單元進行調整，由此所得的數據對陜北地區的實際投入具有很好的指導意義。
  3. Two detection methods of chirp signals are presented in the dissertation : the cyclic autocorrelation detection method and the correlation detection method of cyclic autocorrelation function. it is shown that the two methods both have an excellent performance of blind detection. the performance analyses of the two detection methods are both carried out for additive noise or multiplicative noise, and the output signal - to - noise ratio ( snr ) expressions of the two methods are also derived

    通過研究提出了兩種線性調頻信號的檢測方法?基於循環自相關函數包絡的檢測方法和基於循環自相關函數的相關函數包絡的檢測方法，兩種方法均可實現信號的盲檢測，有良好的檢測性能，文中還分析了加性噪聲及存在乘性和加性噪聲情況下兩種檢測方法的性能，推導出了輸出信噪比公式。
  4. On the base of above it, this paper discuss the synthesis of optimum distributed arrays by nonuniform spacing in the sense of dolph - chebyshev. having derived the equations of optimum element distribution, we analyze the exponentially spaced array, which are optimum when the elements are isotropic and equally weighted, and the array by general raised cosine function. the formulate for estimating the sidelobe envelope, beamwidth of the array pattern and clean region width are obtained

    推導了最佳陣元分佈方程，分別對陣元無方向性和等加權時的最佳分散式陣列? ?指數間隔陣列和採用廣義升餘弦加權的最佳分散式陣列進行了分析，推導了天線方向圖旁瓣包絡、波束寬度，干凈掃描區寬度的估計公式，給出了近軸旁瓣電平與陣列參數的關系。
  5. With the new - simple method, the equation of circle - arc - enveloping curve are deduced. also the relationship between the arc radius, the radius of center distribution and the distance of centers is given to avoid undercutting

    文中採用新方法推導出了圓弧包絡線轉子型線方程，還給出了避免出現根切現象的圓弧半徑、圓弧圓心分佈圓半徑以及中心距三者之間的關系。
  6. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  7. The paper includes four sections followed here : the first section studies the modeling of signals of pulse doppler radar seeker, and establishes a radar signal simulation model, including radar emitting signal model, receiving signal model, receiving echo signal model, clutter model, noise model, sum channel directional pattern of antenna model, difference channel directional pattern of antenna model, sheltering model, rcs model, glint noise model, etc. the second section studies signal processing of pulse doppler radar seeker, and establishes radar signal processing mathematical model and data processing mathematical model for simulation, including windowing, doppler filtering, envelope demodulation, pdi, cfar, centering, velocity tracking, angle tracking, a - b filtering, etc. the third section studies the modeling of modified proportion guiding, and establishes guiding model, then dynamic simulation results is provided

    論文的主要工作包括四部分：第一部分研究了脈沖多普勒雷達導引頭的信號建模問題，建立了雷達信號模型，主要包括：發射信號模型、接收信號模型、目標回波信號模型、雜波模型、噪聲模型、和差通道天線方向圖模型、遮擋因子模型、接收機噪聲模型、目標雷達截面積統計性模型、目標角閃爍模型等。第二部分研究了脈沖多普勒雷達導引頭的信號處理模式，建立了信號和數據處理模型，主要包括：加窗和多普勒濾波、包絡檢波、檢波后積累、頻域cfar處理、速度定心、速度跟蹤、角跟蹤、 ?濾波等，然後給出了信號處理流程。
  8. Abstract : in order to solve the double parameters enveloped in the geartooth flank generating, the complicated double parameter envelope is simplified to the generating process between work - piece and imaginary crown generating gear by means of mathematical transformation. the equation of the imaginary crown generating surface and the partial derivatives are deduced, so the differential geometric parameters of the generating surface can be obtained. by analyzing the generating motion between the imaginary crown generating gear and the work - piece, all the first to third order geometric parameters of the generated tooth flank at any given point can be calculated

    文摘:為了解決直接求解展成法加工中存在的復雜雙參數包絡問題時的困難，提出通過數學變換，將此包絡問題轉化為假想平面產形輪與工件之間的展成問題來進行研究.推導了假想產形面的方程和各階偏導矢，於是可獲得產形面的微分幾何參數.通過分析假想平面產形輪與工件之間的展成運動，即可得到被展成齒面上任意指定點的全部一至三階微分幾何參數
  9. ( 3 ) analysis the influences to the technological innovation patterns of dg tncs by four industrial types ( resource industry, compare advantage industry, marginal industry i and marginal industry ii ). and make the empiricism research of chinese home appliance market. ( 4 ) have put forward the technological innovation models of " technological & marketing coupling model ", " backward integrated model ", " systems integration & networking model " of dg tncs. ( 5 ) distinguish the specific learning way of dg tncs technological innovation management, and analyze the innovation learning effect of developing country, developed countries and china tncs with dea. ( 6 ) point out the problems of chinese transnational corporation technological innovation pattern, and give out the countermeasure and suggestions

    論文的主要創新點包括： （ 1 ）根據影響發展中國家跨國公司技術創新模式的主導因素，從國家、產業、企業層面分析發展中國家跨國公司技術創新模式； （ 2 ）提出影響發展中國家跨國公司技術創新模式的in ? ir框架，總結了工n一1r框架下發展中國家跨國公司技術創新的部分特徵; （ 3 ）分析資源產業、比較優勢產業、邊際產業i和邊際產業h四類產業影響下的發展中國家跨國公司技術創新模式，並結合中國家電業的現實作實證分析; （ 4 ）提出了「基於技術、市場作用」的發展中國家跨國公司技術創新模型、發展中國家跨國公司「倒一體化」創新模式和發展中國家跨國公司的系統集成網路創新模式; （ 5 ）區分發展中國家跨國公司技術創新管理的各種「學習」方式，運用數據包絡分析等方法比較分析發達國家、發展中國家和中國的跨國公司技術創新學習的效果和特點; （ 6 ）指出我國跨國公司建立技術創新模式過程中出現的問題，並提出對策和建議。
分享友人
分享到 Line

分享到臉書