屈壓載荷 的英文怎麼說

中文拼音 [qūyāzǎihé]
屈壓載荷 英文
collapsing load
  • 壓 : 壓構詞成分。
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 荷 : 荷名詞（蓮） lotus
  • 載荷 : load; loading載荷變化 load fluctuation; variation in load; 載荷裝置 load device
  1. Here we obtain the strain compatibility method ande equilibrium of forces and concepts of fracture mechanincs, they can be used to predict the ultimats strength in flexure that can be achieved by such elements, given the cfrp cross - sectional area, or conversely, the required cfrp cross - sectional area to achieve a targeted resisting moment of rehabilitated flexureal elements

    Cfrp加固梁在承受彎曲荷載時的破壞是鋼筋屈服后碳纖維斷裂和鋼筋屈服后混凝土壓碎。本文通過應變相容方法和對破壞機理的定義，由給定的cfrp橫截面積預測加固梁的極限彎曲強度；或者相反，在已知加固梁的極限彎曲強度時可以求出所需的cfrp橫截面積。
  2. First, the dynamic stability of braid composite cylindrical shells with the influences of some main factors is introduced. the general governing equations for the nonlinear dynamic stability is obtained. by the hamilton principle. the creep buckling analysis of braid composite cylindrical shells under axial compression and the dynamic stability under nonconservation force are discussed as emphases. in creep buckling question, by means of theoretical analysis, the instaneous critical load and durable critical load of viscoelastic braid composite cylindrical shell under axial compression are obtained and the numerical example is given

    首先介紹了編織復合材料圓柱殼在幾種主要因素影響下的動力穩定性問題，用hamilton原理建立非線性動力穩定性問題的一般性基本方程。然後重點討論了編織復合材料圓柱殼軸壓下的蠕變屈曲問題及非保守力作用下的屈曲問題。對蠕變屈曲問題，通過理論分析來得到了編織復合材料圓柱殼的瞬時彈性臨界載荷和持久臨界載荷，給出了具體的算例。
  3. The following conclusions are gained : ( 1 ) the located shear band prongs the ligament near the top crack tip and the structure may occur shear - mode fracture at the angle of 155 ? to crack when load is 87. 92mpa ; the mode of fracture of the flange joint structure is not possible to be void - mode ; ( 2 ) it is proved that loading and then unloading repeatedly can not increase the possibility of invalidation of the structure when the times of loading and unloading are not too more when load is operating pressure ; the structure is safe when the vessel is operating ; ( 3 ) in the fe model of the thesis, not considering the influence of water pressure test which is in the process of fabrication of vessel in fe results in larger deviation in analysi

    得出了以下結論：在8792mpa的載荷下筒體一封頭連接結構處的集中剪切帶貫穿韌帶，可能發生沿與原裂紋線成155 「角方向剪切型斷裂；筒體一封頭連接結構不可能發生韌窩型斷裂； （ 2 ）在工作壓力下進行次數不多的反復加、卸載，結構不會破壞，也不會喪失安定性：結構在工作狀態下是安全的； m在本文的彈塑性有限元模擬計算中，對于裂紋尖端進行力學分析時，不考慮壓力容器製造過程中水壓試驗的影響，將導致計算結果出現較大的偏差； （ 4 ）筒體完全屈服時的載荷為92石3mpa ，封頭完全屈服時載荷為86
  4. A fem of elasto - plastic flexural - torsional buckling of steel members under cyclic loading

    循環荷載下壓彎鋼構件彈塑性彎扭屈曲的有限單元法
  5. Inelastic yield load of concrete filled steel tubular middle long columns under axial compression

    鋼管混凝土軸壓中長柱的非彈性屈曲荷載
  6. In accordance with the occurrence behavior of roof strata and the fracture characteristics of key stratum in shallow seam longwall mining, studied post - buckling behavior of roof key stratum in the process of mining by using initial post - buckling theory, which derived a critical load and a breaking span of the main roof during the first weighting, determined the final subsidence and the maximum rotation angle for broken key stratum, and presented an application with the example of daliuta 1203 face

    摘要根據淺埋煤層頂板巖層的賦存特點和長壁開采時關鍵層的變形破斷特徵，應用初始后屈曲理論探討了開采過程中頂板關鍵層的后屈曲性態，得出了老頂初次來壓時頂板的臨界載荷和破斷步距，確定了頂板破斷后的極限下沉量和回轉角，並以神東礦區大柳塔1203工作面為例給出了工程實例。
  7. In the formula, our experience in structural strength design and the experimental results are considered. and such factors are also considered as differences in materials of the skin and the reinforcer, effects of bending, torsion, stretching and offcenter of the reinforcer. furthermore, through post - buckling stress analysis of the skin, it is shown that even low stress level will result in buckling of the skin, but the skin still has loading capacity

    在總結過去結構強度設計和試驗分析的基礎上，應用扁殼理論，在廣義力與廣義應變關系中考慮了蒙皮與加筋不同材料以及加筋的彎曲、扭轉、伸縮和偏心等的影響，推導出適合於工程應用的加筋殼結構軸壓屈曲臨界載荷的計算方法;並通過對薄壁結構蒙皮后屈曲應力分析，說明蒙皮在很低的應力水平時就出現失穩現象，但失穩后的蒙皮仍具有一定的承載能力。
  8. In this paper we study the transverse stiffeners of the thinned - web beam bearing several concentrated longitudinal strain actions. thinking of using post - buckling strength of web plate, we study some facts about tran sverse stiffeners including strain ability, condition of breaking, calculation of strength and stabilization of the stiffener bearing regional load action

    本文對受多個集中荷載作用的薄腹板梁的橫向加勁肋進行了研究，分析了利用腹板屈曲后強度時，橫向加勁肋的受力狀態、破壞機理，以及加勁肋局部承壓的強度計算公式和穩定計算方法。
  9. With the different loading ratio of parallel to axis and normal to axis direction, damage defects will occur bulking problem. by varying the degree of material anisotropy relative to the loading axis such as poisson ' s ratio and shear modulus, crack growth bulking strain value parallel to or normal to the loading axis is different. the parameters controlling the growth or arrest of the delamination damage are identified as the geometry and the depth of defects and radius of cylindrical etc. at last, it was investigated that the delamination damage is often induced by the tip of matrix damage under higher stress

    研究結果表明:殼體筒段受軸向拉伸和內壓載荷作用時，軸向和環向載荷的比率不同，母層和子層可能發生拉伸屈曲，也可能發生收縮屈曲，或者同時發生拉伸和壓縮屈曲;母層與子層各向異性存在差異，即泊松比與剪切模量不匹配時，將使子層板的邊界上承受壓縮和剪切作用，當分層達到臨界狀態則發生屈曲，當母層與子層的各向異性差異越大，則發生分層屈曲的可能性越大;分層損傷的屈曲應變值與子層自身的彈性模量、分層子層的形狀、厚度以及圓柱半徑等因素有關。
  10. In the small deflection theory, by buckling analysis, the classical buckling critical load of integrative braid composite cylindrical shells under axial compression is get. according to the experience and the results of fem, a revised formula for calculating buckling critical load is presented

    在小撓度理論中，通過前屈曲分析得到了完善的編織復合材料圓柱殼在軸壓情況下的經典屈曲臨界載荷，根據經驗及有限元計算結果，提出了計算屈曲臨界荷載的修正公式。
  11. At first, the experiment carried out by tianjin university has been analysed according to the " nonlinear balance trying calculation " method, and the values of yield load and ultimate load agree with the test result better, and the curve of bending moment - curvature, bending moment - deflection can agree with the results. the second, the simplified formula for evaluation the ultimate flexural capacity of cfrp strengthened rc members is presented according to the three probable failure modes ( compression failure ; cfrp rupture ; crushing of the concrete in compression before yielding of the reinforcing steel ). it is applicable to both singly and doubly reinforced rectangular sections, as well as flanged sections

    首先利用鋼筋混凝土非線性平衡試演算法對天津大學試驗進行了理論分析，所得分析值與試驗結果相比，加固梁的屈服荷載、極限荷載能夠很好地吻合，彎矩曲率關系曲線及彎矩撓度關系曲線較為吻合；其次，為了滿足實際工程的需要，根據碳纖維布加固構件可能發生的三種破壞形態（壓區混凝土壓碎破壞、碳纖維布拉斷破壞以及受拉鋼筋尚未屈服時壓區混凝土已壓碎破壞） ，區別三種鋼筋混凝土構件截面形式（單筋矩形截面、雙筋矩形截面、 t形截面） ，分別給出了碳纖維布加固混凝土構件抗彎承載力的簡化計算公式和適用條件，並進一步探討了這三種截面形式下進行加固設計和復核的步驟。
  12. Because of its simplicity of the critical moment and the good precision, the solutions based on gjelsvik theory are used in the elastic - plastic phase. the ultimate load carrying capacity of box section beams are calculated considering the effect of plasticity and residual stresses

    其次，運用基於gielsvik約束扭轉理論推導了箱形偏壓桿的彈性彎扭屈曲荷載，同時給出了壓彎桿在彈性彎扭屈曲的軸力和彎矩相關關系。
  13. Cfrp strengthening of concrete beams can fail when steel yield - concrete crushing and steel yield - cfrp tenside rupture

    Cfrp加固梁在承受彎曲荷載時的破壞是混凝土壓碎、鋼筋屈服、碳纖維未拉斷。
  14. This paper is the research on the local interactive buckling behavior of cold - formed rectangular tube under uniform compression. the paper includes the following main contents : ( 1 ) an elastic interactive buckling model is presented on the basis of the theory of elastic plates. under the equilibrium condition and deformation compatibility condition, analytical expressions are derived to predict the interactive bucking load pcr

    本文主要研究冷彎薄壁矩形鋼管均勻受壓下板組的相關關系，包括以下主要內容： （ 1 ）建立了彈性相關屈曲解析法分析模型，考慮平衡條件及變形協調條件，建立板組的屈曲微分方程，得出了板組相關屈曲的臨界荷載p _ （ cr ）的計算行列式。
  15. ( 2 ) the finite element program ansys is used to analyze the elastic buckling of rectangular tube, consequently the buckling load pcr and the simulating formula for the restraint coefficient &, is obtained. the results derived from the program are compared with the british standard and china standard

    （ 2 ）採用有限元程序ansys對矩形鋼管板組進行了彈性屈曲分析，得出其臨界荷載p _ （ cr ） ，彈性屈曲模態與解析法所作假設相符，並擬合出均勻受壓下的矩形鋼管約束系數k _ 1的公式，並與英國規范和我國規范進行比較。
  16. Focuses are then put on the flexural torsional buckling analysis of mono - symmetry i - section arches. closed form solutions are obtained for arches subjected to uniformly distributed radial load and to equal and opposite end moments. effects of different laying positions and of asymmetry of cross - section on buckling loads are included

    在這個基礎上，對單軸對稱工字形截面拱在均勻受壓和均勻彎曲條件下的屈曲問題進行研究，給出臨界荷載的理論解答；分析了工字形截面不同放置形式和截面不對稱性對拱臨界荷載的影響，並與已有的理論進行比較。
  17. Thne results show that not only the nonlinear elastic critical pressure is much less than linear one, but also the inner pressure can significantly enhance the critical buckling axial load, so it provides a elastically theoretical basis for internal high - pressure forming technology

    計算結果表明不僅非線性彈性臨界載荷遠低於線性彈性臨界載荷，而且更重要的是內壓很大程度上有助於提高柱殼軸向彈性臨界屈曲載荷，這樣為內高壓成形工藝提供了彈性失穩理論依據。
分享友人
分享到 Line

分享到臉書