屈曲部 的英文怎麼說

中文拼音 [qūqūbù]
屈曲部 英文
winding portion
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 部 : Ⅰ名詞1 （部分; 部位） part; section; division; region 2 （部門; 機關或組織單位的名稱） unit; mini...
  1. The numerical results show that the elephant foot bulging is in fact buckling failure which is caused by the overcritical compressive stress rather than intensity failure

    分析表明：立式儲液罐罐壁「象足」變形主要是由罐壁縱向壓應力超過臨界應力而產生的局部屈曲破壞，並非強度破壞。
  2. The ship ' s hull is a thin - walled box girder structure composed of stiffened panels. the overall failure of a ship hull girder is normally governed by buckling and plastic collapse of the deck, bottom, or sometimes the side shell stiffened panels. therefore, the analysis of buckling and ultimate strength of ship panels in deck, boltom, and side shells is very important and necessary for the safety assessment of ship structure. in stiffened panels, local buckling and collapse of plating between stiffeners is a basic failure mode, and thus it would also very important to evaluate the buckling and ultimate strength interaction of plate elements under combined loads

    船體梁的總體失效通常取決于甲板、船底板，有時候是舷側加筋板的屈曲和塑性破壞。因此，對于衡量船體結構的安全性而言，對甲板、底板、舷側板進行屈曲和極限強度分析是十分重要且必須的。對于加筋板而言，加強筋間的板格之局部屈曲和失效是最基本的失效模式。
  3. In the hogging condition, double bottom and the side shell remain the ultimate bucking strength, deck and upperwing tank remain the yield stress, and the other parts keep elasticity. then the key to calculate the ultimate strength of ship hull girders is to ascertain the ultimate bucking strength of the stiffened panels. in this regard, the developed formulation is designed to be more sophisticated than previous simplified theoretical method for calculating the ultimate strength of stiffened panels under combined in - plane bending and lateral pressure. fabricatio n - related initial imperfections ( initial deflections and residual stresses ) are included in the panel ultimate strength calculation as parameters of influence. all possible collapse modes involed in collapse of stiffened panels, including overall buckling collapse, column or beam - column type collapse, tripping of stiffeners and local bukling of stiffened web are considered

    確定了船體梁整體破壞時的剖面應力分佈之後，關鍵在於確定板架的極限屈曲強度。本文充分考慮了在縱向彎曲、橫向壓力作用下加筋板可能發生的幾種破壞模式，即板架的整體屈曲破壞、樑柱形式的破壞、筋的側傾、腹板的屈曲並同時考慮了初始焊接殘余應力、初撓度的影響，使其更精確的計算加筋板的屈曲強度。對于加筋板中加強筋腹板的局部屈曲，採用解析法推導出筋的腹板的撓度方程及其邊界條件，求解相應的方程，從而計算出腹板的局部屈曲應力。
  4. While exercising, be sure not to overexert yourself. for example, don t turn your head and neck too hard or too fast, and avoid deep knee bends

    運動時切勿用力過度或者過大動作，例如避免頭部及頸部轉動時動作過大或動作過快，以及避免雙膝過份屈曲的動作。
  5. The kink might result from over - bending of the softening tube in the oral cavity due to oral temperature and neck flexion

    造成氣管內管彎折的可能原因是因為頸部屈曲及口腔溫度較氣管內管高以致管子變軟所導致的過度彎曲。
  6. This manipulation is operated by the tip of the middle finger or the joint of the index and middle finger, pounding at the certain points or part regularly

    用中指指端或食指、中指屈曲后的近側指間關節突起部為著力點，在一定的穴位或部位上做有節律地點擊，稱為「搗法」 。
  7. Bracing members in concentrically braced structures may be subjected to large cyclic deformations due to local buckling during a severe earthquake causing possible early fractures

    摘要在罕遇地震下，框架中心支撐結構中的鋼支撐常因局部屈曲位置的低周疲勞開裂而過早退出工作。
  8. In the analysis of the elastic local buckling strength of the stiffener ' s web, the elastic critical stress is analytically derived by solving the characteristic value problem involving the governing differential equation under the corresponding loading and boundary conditions

    對于加筋板中加強筋腹板的局部屈曲，則用解析法推導出筋的腹板的撓度方程及其邊界條件，求解相應的方程，從而計算出腹板的局部屈曲應力。
  9. In this paper we study the transverse stiffeners of the thinned - web beam bearing several concentrated longitudinal strain actions. thinking of using post - buckling strength of web plate, we study some facts about tran sverse stiffeners including strain ability, condition of breaking, calculation of strength and stabilization of the stiffener bearing regional load action

    本文對受多個集中荷載作用的薄腹板梁的橫向加勁肋進行了研究，分析了利用腹板屈曲后強度時，橫向加勁肋的受力狀態、破壞機理，以及加勁肋局部承壓的強度計算公式和穩定計算方法。
  10. The buckling of a plate mostly occurs in elastic regime with high strength steel adopted widely, and the plate reaches ultimate strength due to losing capacity when equivalent stress where maximal in - plane compressive stress appears arrives at yield in post - buckling phase

    隨著高強度鋼的廣泛應用，板格屈曲大部分發生在彈性范圍內，在後屈曲階段當板格最大面內壓縮應力處的等效應力達到屈服極限時，板格迅速卸載，此時板格達到極限強度。
  11. Local buckling is an important buckling mode of thin - walled and cold - formed steel columns, and the interactive behavior of component plate elements cannot be ignored

    局部屈曲是冷彎薄壁型鋼構件主要的屈曲模式，屈曲時板件之間的相關作用也是不容忽視的。
  12. Gabled frames are widely used in industry and civil engineering, it ' s web plates " local buckling calculated formula in the technical specification for steel - structure of one - storey light - weight buildings with gabled frames ( cecs102 : 98 ) are based on the rectangular plates " and did n ' t consider the interaction of the fringe plate. so, there are some different between the actual members and the prescript of the specification, and the post - buckling strength ' s calculated formula is based on the local buckling ' s, it must have some unreasonable

    楔形門式剛架廣泛地應用於工業與民用建築中， 《門式剛架輕型房屋鋼結構技術規程》 （ cecs102 ： 98 ）中楔形腹板局部屈曲的計算公式來自矩形板，並且沒有考慮翼緣的相關作用，因此，規程中的規定與構件的實際工作狀況有一定的差異，且屈曲后強度的計算公式也是以局部屈曲系數為基礎的，勢必有其不合理性。
  13. Emphasis is also laid on the importance of properly positioning of the head and neck prior to any operation especially in craniotomy

    我們更強調在任何手術開始前就要注意頭頸部的位置是否過度伸展或屈曲。
  14. This thesis used along caldwell ' s direct calculation method of the ultimate strength of ship hull girders, considered the double bottom and upperwing tank to ship ultimate strength contribution, first defined the stress distribution of the whole section of the ship girders. that is : in the sagging condition, deck and side shell of nearby deck remain the ultimate bucking strength, double bottom remain the yield stress. and the other parts keep elasticity

    本文沿用caldwell等人直接計算船體極限強度的思想，考慮雙層底和頂邊水艙對船體極限強度的貢獻，首先將船體梁整體破壞時剖面應力分佈確定為：在中垂狀態下，甲板及甲板附近的舷側均屈曲，雙層底區域則均屈服，其他部分保持彈性狀態；在中拱狀態下，雙層底及之間的底舷側均屈曲，甲板及頂邊水艙區域均屈服，其他部分則保持彈性狀態。
  15. Local buckling is the dominant failure mode for composite steel column

    摘要局部屈曲是組合鋼柱常見的失效模式之一。
  16. According to three dimension braided composites for braided technology - four - step and technology - two - step procedure, and with reference to theories of braided fabric geometry and force models, a geometric model is built. in this model, the cross - section of thread is described as a circle and thread path as a cubic b - spline. braided - fabric structures in three dimensions are displayed by using solid - modeling techniques

    本文三維編織物根據四步法和二步法編織工藝，從紗線的力學模型出發，建立了以圓形近似描述紗線的截面形態，以三次b樣條曲線近似描述紗線的屈曲形態的織物空間幾何模型，利用計算機三維實體造型技術，分別建立各自的編織物實體模型，用來模擬織物內部各紗線的空間位置，完成織物結構模擬。
  17. Prevention of functional disability of knee joint bend of postoperative fracture of femoral condyle and rehabilitation

    股骨髁部骨折術后膝關節屈曲障礙的預防及康復
  18. Local buckling capacity of steel composite beam subjected to combined bending, shear and patch loading is one of key problem in steel structures design. the computational formula for local stability of web was based on the assumption of infinite - elastic perfect plates in the steel structures design code ( gbj17 - 88 ). but in the revised code ( gb50017 - 2003 ), this formula was made big change with reference to british code ( bs5950, partl ) and australian code ( as4100 ), the related research result of our country was included as well. in the modified formula, influence of early geometric imperfection and elastic - plastic buckling stage were considered, which is compatible with both actual circumstance of engineering and the strength formula of beams under bending stresses ( considering partial plasticity of the section ). in this paper, the preceding problem is deeply analyzed and studied, considering the effects of various geometric parameters and stress combinations on buckling critical stress of web, the revised local buckling correlative formula for transverse and longituded stiffened web panels under combined stresses is analyzed and verified by finite element method

    組合鋼梁腹板在彎、剪及局壓復合應力作用下的局部屈曲承載能力是鋼結構設計中需考慮的問題，新的《鋼結構設計規范》 （ gb50017 ? 2003 ）對此部分內容作了較大改動，原規范中關于腹板局部穩定的計算公式是基於無限彈性的完善板假定；新的規范則參考了英國規范（ bs5950 part1 ）及澳大利亞規范（ as4100 ）並結合我國相關研究成果，考慮了屈曲進入彈塑性階段以及初始幾何缺陷的影響。這不僅與工程實際情況相符，而且也與鋼梁在彎曲應力作用下允許截面部分進入塑性的計算公式相協調。
  19. In this thesis theoretical solution of inhomogeneous polar orthotropic plate was deduced and plate with clamped edges was taken as example. the displacement in radius direction, inner - force in radius direction, inner - force in annulus direction and buckling load with different core - radius ratio were worked out. the effect of core - radius ratio to the result was discussed in the conclusion

    本文從理論上推導出了非均勻極正交各向異性圓板的精確解，並且以夾支圓板作為算例，計算了在不同核徑比的情況下，圓板受外部縱向均布載荷作用后的徑向位移、徑向內力、環向內力，以及屈曲載荷，討論了核徑比對計算結果的影響。
  20. ( 4 ) introducing how to evaluate load capacity pn of wall stud considering post buckling strength of plate element. local buckling effects are determined according to the effective width method used in specifications gb50018 _ 2002 and aisi96

    （ 4 ）參照gb50018 、 aisi96二本現行規范，採用有效寬度法考慮局部屈曲后強度並對非彈性屈曲應力進行修正，給出了考慮局部屈曲影響和進行非彈性修正後立柱的穩定承載能力p _ n 。
分享友人
分享到 Line

分享到臉書