工作壓力角 的英文怎麼說
中文拼音 [gōngzuòyālìjiǎo]
工作壓力角
英文
operating pressure angle-
The paper studies the surface geometry of globoidal indexing cam by applying the theory of conjugate surfaces and the method of coordinate transformation, presents the equations related to the main inducement curvature of the cam profiles, analysis and deduces the equations of two circumscription curves, which judge if the conjugate surface could mesh properly. some calculate examples and conclusion are given. the surface equation of the globoidal cam and conjugate equation are established
論文首先在分析空間嚙合原理基礎上，採用坐標變換法推導出弧面分度凸輪的工作廓面方程、嚙合方程和壓力角計算公式，對弧面分度凸輪的嚙合特性進行了深入的分析和研究，對判斷曲面能否正確嚙合的依據如兩類界限線方程以及誘導主曲率等進行推導，並給出算例。Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle
流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。Abstract : in the research of internal combustion engine, recordingin - cylinder pressure and temperature is an essential technique to study the thermal cycle of internal combustion engine. the combustion analyzer developed in this study will give both the measurements at sampling points per crank angle or sampling cycle, calculate and show the real time parameters which decide the working process of internal combustion engine, such as pressure accelerating rate, indicateed mean effective pressure, cycle - to - cycle variation, heat release rate, etc. compared with the imported congeneric products, the analyzer has many advantages such as chinese interface, low price, easy operateing, convenience in maintainance and easy upgrading
文摘:為了測錄內燃機缸內的壓力及溫度，開發了一種內燃機燃燒分析儀.該分析儀由國產高速數據採集卡及自行開發的控制軟體組成.它不僅能精確設置每度曲軸轉角內采樣點的個數和採集循環數，而且在採集過程中能實時計算和表徵內燃機工作過程的壓力升高率、平均指示壓力、循環變動率、放熱率等參數.經實際使用以及與國外產品相比表明，此分析儀具有全中文界面、價格低、操作簡單、使用維護方便、功能便於擴充等優點The aircraft used throughout the hydraulic system, two aircraft integration design pressure and pressure and pressure and can independently accomplish suing time control moves make big vehicles with tight solid, more eggective your savings artificial, time, electricity and lower costs, improve efficiency, it can help make up the hydraulic pessure at the end of the department to achieve shoes second fill pressure of functions to enhance the quality of diesel
本機採用油壓系統，兩機一體設計，壓邊及壓前後均能獨立完成，採用時間控制動作，出力大，貼合緊牢固，更為你有效的節省人工、時間、電力及降低成本，提高工作效率，可以彌補全油壓壓底機死角之處，達到鞋子二次補壓之功能，提升壓著品質。The study, conducted by dr siu oi - ling, an associate professor at lingnan universitys department of politics and sociology, and fourteen overseas scholars, reveals that greater china managers mean stress level induced by work - family conflicts, at 33. 6, is higher than the 25. 7 and 32. 2, suffered by the english - speaking and latin american managers, respectively the full score is 54
有報告顯示大中華地區的管理人員因工作崗位與家庭角式引起沖突，而導致有工作壓力的平均水平為33 . 6 ，高於分別只有25 . 7的英語國家管理人員及32 . 2的拉丁美洲管理人員滿分為54 。The paper also does some deep research on the mesh characteristic of the mechanism, analyses the cause o f the cam profile error and index error during working, using object - oriented method, vc + + and pro / toolkit, performs second development to pro / engineer, completes entity proplasm of the cam mechanism using only few parameters, the press angle calculate module, error analysis module and curvature calculate module are built on the basis of it
然後通過對弧面分度凸輪加工中產生廓面誤差及工作時產生分度誤差原因的分析，建立了計算加工和分度誤差的數學模型。應用vc + +和pro toolkit對pro engineer進行二次開發，建立了弧面分度凸輪機構的參數化設計和三維造型及壓力角、誘導主曲率等運動特性和誤差分析軟體系統。The shear mechanism, failure mode, deformation capacity, bearing capacity and the reliability of the anchored angle steels of the wrapped steel concrete cast - in - site frame typical story exterior joints under the middle and high axial compression ratio ( n = 0. 3, 0. 5, 0. 6 ), the working performance, failure mode, and the shear capacity of top story joints under the crack moment, the hysteresis characteristic and the dissipation energy capacity of the test joints are all analysed based on the 1 / 4 model pseudo - static tests of five specimens of wrapped steel concrete cast - in - site frame exterior joints, which varied in axial compression ratio, distribution of the beam angle steels and the stirrup ratio
基於上述分析，本次試驗通過五個外包鋼混凝土邊節點1 4比例模型的偽靜力試驗，以柱的軸壓比、梁角鋼布置形式、配箍率等為主要參數，分析外包鋼混凝土現澆框架一般層邊節點在中高軸壓比（ n = 0 . 3 、 0 . 5 、 0 . 6 ）條件下，節點的抗剪機理、破壞模式、變形能力、承載能力和角鋼錨固的可靠性；分析了頂層邊節點在張開彎矩作用下的工作性能、破壞模式和抗剪承載力；分析了試驗節點的滯回性能和耗能能力。The research, entitled a cross - national comparative study of work - family stressors, working hours and well - being : china and latin america versus the anglo world, indicates that in general managers feel stronger that work - family conflicts are a source of stress the longer hours they work. the strength of this relationship is the highest among english - speaking countries managers
這項名為工作與家庭角式沖突及工作壓力跨國比較研究：大中華，拉丁美洲及英語國家，顯示管理人員的工作時數愈長，他們愈感受到壓力源頭來自工作崗位與家庭角色之間的沖突，而此關系在英語國家的管理人員中最為強烈。A new calculation method for optimizing diesel engine performance, called nonlinear regression - mess method, is put forward. in this paper, 25 groups of simulated values are calculated from the diesel engine working model, specific fuel consumption, peak pressure, rate of pressure rise, nox and peak temperature are fitted into explicit function about compression ratio and fuel injection advance angle
本文利用柴油機工作過程模型，得出25組模擬計算數據，利用非線性回歸將油耗、最大爆發壓力、壓力升高率、 no _ x濃度及最高燃燒溫度擬合成壓縮比和噴油提前角的顯函數，並用網格法進行優化，用c語言編制了優化計算程序，得出最佳的壓縮比和噴油提前角，使其優化匹配。Work - family conflict ( wfc ) is a particular type of interrole conflict in which the role pressures from the work and family domains are murually incompatible in some respects
工作家庭沖突（ wfc ）是來自工作和家庭生活領域的角色間沖突的一種特殊形式。在這種雙向性沖突中，某些角色壓力是不相容的。( 4 ) female cadres " competence of job adaptation, planning, positive response when emergency, self - control, coordination, pressure and support from leaders, support for innovations, opportunity for individual development and adaptation influence their performance significantly. but role cognition and rules to goal influence it little. ( 5 ) what makes the male and female ' s competence different is not social or organizational environment or performance, but their background factors
（ 4 ）女幹部的職業適應能力、自我能力、計劃工作能力、應急監控能力、授權指揮能力、溝通上下與部門的關系能力以及領導壓力因素、領導支持因素、創新支持因素、發展空間因素、組織適應因素對她的績效影響較大；而角色認知能力與目標規則因素與她的績效相關度較小。The following conclusions are gained : ( 1 ) the located shear band prongs the ligament near the top crack tip and the structure may occur shear - mode fracture at the angle of 155 ? to crack when load is 87. 92mpa ; the mode of fracture of the flange joint structure is not possible to be void - mode ; ( 2 ) it is proved that loading and then unloading repeatedly can not increase the possibility of invalidation of the structure when the times of loading and unloading are not too more when load is operating pressure ; the structure is safe when the vessel is operating ; ( 3 ) in the fe model of the thesis, not considering the influence of water pressure test which is in the process of fabrication of vessel in fe results in larger deviation in analysi
得出了以下結論：在8792mpa的載荷下筒體一封頭連接結構處的集中剪切帶貫穿韌帶，可能發生沿與原裂紋線成155 「角方向剪切型斷裂；筒體一封頭連接結構不可能發生韌窩型斷裂； （ 2 ）在工作壓力下進行次數不多的反復加、卸載，結構不會破壞，也不會喪失安定性：結構在工作狀態下是安全的； m在本文的彈塑性有限元模擬計算中，對于裂紋尖端進行力學分析時，不考慮壓力容器製造過程中水壓試驗的影響，將導致計算結果出現較大的偏差； （ 4 ）筒體完全屈服時的載荷為92石3mpa ，封頭完全屈服時載荷為86To improve the transmitting characteristic and decrease the output work has a direct effect on the enhancement of the operating property and life - span of the operating mechanism of vacuum circuit breakes. based on the characteristics of polynomial rule of the cam movement, considering the pressure angle of cam device, an optimization model is established, with the coefficients of polynomial rule of cam movement as the optimizing variable, and the minimum output work of the mechanism as the object function. with the optimization tool box of matlab, the optimization process is conveniently completed and the perfect result of optimization design is obtained
改善真空斷路器操動機構的傳動運動特性，減小真空斷路器的操作輸出功，對提高真空斷路器的操作使用性能及壽命都具有直接的影響.利用凸輪機構的多項式運動規律的特點，以凸輪多項式運動規律的多項式系數為優化變量，以斷路器操動機構最小的輸出功為目標函數，考慮操動機構合分閘時凸輪機構傳動壓力角的情況，建立了彈簧操動機構中凸輪機構的優化數學模型，並利用matlab語言的優化工具箱方便地實現了優化過程，得到了較理想的優化設計結果Analyzing the finished sprinkler products in our country and overseas, testing all sorts of sprinkler parameters ( elevation of sprinkler, diameter of the nozzle, working pressure, the range of water, uniformity of spray irrigation, intensity of spray irriga tion, the degree of atomization ) so as to compare with the new style sprinkler install with pressure adjuster
對國內和國外的一些中壓噴頭成品進行分析、研究、測試取得實際的各項參數（噴射仰角、噴嘴直徑，工作壓力、射程、噴灌均勻度、噴灌強度、霧化程度）以便和安裝「壓力調節器」后的噴頭進行比較23. testing all the hydraulic parameters of the sprinkler installed with adjuster such as working pressure, water flux, the range of the sprinkler, intensity of water drop impact, characteristic of water distribution, etc. according to the testing data, we can learn the quantitative relations among the structure of the adjuster, working pressure, diameter of the nozzle, elevation of sprinkler, wind power, velocity of rotation and the range of water
測試安裝「壓力調節器」后的噴頭的水力性能參數，即工作壓力、流量、射程、水滴的打擊強度、噴灑水分佈特性等。依據所測得的噴頭水力性能參數和射程數據，我們可較清楚的了解「壓力調節器」的結構形式、工作壓力、噴嘴直徑、噴射仰角、風力、旋轉速度和噴頭射程之間的定量關系。Abstract : this paper explores the interelations between the work efficiency and the pressure angle of a cam machine, and expounds the theory of selecting and confirming for the optimal permissive pressure angle of cam, and introduces the design means that can be used in engineering practice
文摘:探討了凸輪機構工作效率與機構壓力角之間的相互關系，闡述了選擇和確定凸輪機構最佳許用壓力角的理論，介紹了可用於工程實際的設計方法According to dr siu, work - family role conflicts are a substantive source of stress, since work can affect family life for example, working overtime will reduce time spent with family and family life can affect work too for example, family obligations will limit time spent on work
蕭博士分析工作與家庭角色沖突是潛在的工作壓力源頭，角色沖突可由工作影響家庭例如：工作超時防礙了陪家人的時間，或由家庭影工作例如：要花時間照顧家人，而沒有足夠的時間應付工作。Dfmc transmission ltd. co. regard product ma nagement as strategy, and quickli develop a71, a87, a93, a100, a121d, a121j, a121q, a130, a148, a164 etc. series gearbox. for exsample, " slow an half pulse " development a148 gearbox, aim the shortcoming of competitors, use bigger press angle, all splay tooth, improve gearing intension and drive smooth ; use inertia tooth link synchronizers which have rapid synchronization with reduced effort, improved engagement conditions, increased performance and service life etc. advantages. combine promotion, political power, public relations and the same price to expand place, to increased the market
變速箱公司把產品開發工作提高到戰略高度來考慮，及時開發出a71 、 a87 、 a93 、 a100 、 a121d 、 a121j 、 a121q 、 a130 、 a148 、 a164等系列中心距變速箱，如「晚半拍」開發的a148變速箱，針對競爭對手產品的薄弱環節和質量缺陷，採用大壓力角、全斜齒，提高了齒輪強度和傳動平穩性；採用慣性齒環式同步器，結構更緊湊、可靠等，技術優勢明顯；並充分利用促銷手段、政治力量和公共關系，採用跟價策略，廣開配套渠道，已形成市場。As early as 1999, we have initiated a staff training programme, combining western iq training and chinese traditional values, to provide our staff with eq training, emotional control and negotiation skill exercises. adopting simple approach and detailed explanations, the occupational therapists trained our staff to alleviate their work pressure, to influence the emotions of debtors, and to use negotiation techniques to arrive at a mutually agreeable repayment arrangement with debtors
職業治療師用深入淺出的方法，指導員工如何為自己減低工作壓力，控制自己和債務人的情緒，從而避開無意義的爭執，並運用談判技巧與債務人達致雙方同意的還款安排，充分發揮中介者與談判專家的角色，以達到三贏的局面。Operating pressure angle
工作壓力角分享友人