工作軋輥 的英文怎麼說

中文拼音 [gōngzuòyàgǔn]
工作軋輥 英文
work roll
  • 工 : Ⅰ名詞1 （工人和工人階級） worker; workman; the working class 2 （工作; 生產勞動） work; labour 3 ...
  • 軋 : 軋動詞[方言]1 （擠） press hard against each other; push against2 （結交） associate with; make f...
  • 輥 : 名詞[機械工程] （能滾動的圓柱形機件） roller
  1. The composite roll of high speed steel has the synthetical life of over ten times more than traditional high cr cast iron roll. now the research and production of the high speed steel for roll are very drastic. in this thesis, the microstructure, heat treatment and performance of high speed steel fe - 2 % c - 4 % v - 4 % mo - 5 % cr - x % w ( wt ) are studied systematically by using metallograph, method of lattice, xrd, sem, eds and hardness

    本文利用金相法（包括黑白金相和彩色金相） 、 x射線衍射（ xrd ） 、掃描電子顯微鏡（ sem ） 、能譜（ eds ）及洛氏硬度分析儀等手段，對復合軋輥用高速鋼fe - 2 c - 4 v - 4 mo - 5 cr - x w （其它部分如未作特殊註明均為質量分數）合金系的顯微組織、熱處理工藝及性能進行了系統地分析。
  2. Drawing module, which is graphic system of 1c ad, consists of geometric and three - dimensional parameterization model design of work roll, backup roll, mill framework and finishing mill

    繪圖模塊由智能cad的圖形處理部分組成，包括工作輥、支撐輥、機架和精軋機的幾何建模和三維參數化設計。
  3. Parametric design makes interface between visual basic 6. 0 and solidworks 2000 on the basis of program driving, and outputs three - dimensional parameterization model of work roll, backup roll, mill framework and finishing mill

    參數化設計以程序驅動為基礎，設計了visualbasic6 . 0和solidworks2000之間的介面，完成工作輥、支撐輥、機架和精軋機三維模型的輸出。
  4. Data processing is performed by pc ， which includes detecting rough error by quartile method base on first order differential, adopting three points algorithm to eliminate deviations of rack displacement and installation, applying minimum containing area method to evaluate the sectional plane radius of roller and realizing it by genetic algorithm, adopting akima method to fit curve of roll profile

    主要的數據處理工作在上位機進行，採用基於差分法的分位數演算法剔除粗大誤差；採用三點式測量原理消除探頭的安裝及運動所產生的誤差；採用最小包容區域法評定軋輥半徑，並應用遺傳演算法實現最小包容區域法的尋優計算；採用阿克瑪插值方法進行輥型的曲線擬合。
  5. Through the simulation of the forming process, we can get the deformations, stress, strain, plastic flowing in sheets and the interface state under impact load and rolling load, the deformation of the sawtooth form and comparing to the initial state, the results above are expressed in computer animated way. and the effect of geometrical ( mainly different form, including 90 degree, isoceles triangle ， 75 degree, and 1. 5 high and wide ), material and technical parameters on the bond strength are analyzed, also including the comparison of different sawtooth form. the optimum parameters are got

    對雙金屬復合板成型過程進行模擬，從而得到在沖擊載荷和軋輥壓力作用下基板和覆板的應力、應變分佈和塑性流動變形規律，復合后的齒形的變形情況與初始齒形形成對比，以動畫的方式模擬成型過程，並分析了不同幾何參數（主要是不同的齒型，其中包括直角齒型、等腰齒型、 75度齒型、 1 . 5高寬齒型） 、材料參數、工藝參數對復合強度的影響，以及不同齒型的變形對比以及齒型對復合情況的影響，提出最優齒型、最優工藝參數，有效地指導了實驗。
  6. The failure study of the wormwheel working surface

    冷軋工作輥輥面剝落的失效分析
  7. The rolls wear characteristics and work roll wear pattern were analyzed theoretically and the quantitative analysis were made in shape control and effect factor in accordance with the rolling conditions

    從理論上分析了輥系在軋制中的磨損特性，工作輥磨損輥型的計算方法，根據實際軋制工況對其板形的調控、影響因素進行了定量分析。
  8. Works on the bending roll system of four - roll rolling mill, the workroll shape variation caused by the force of bending roll and the contact stress between rolls was researched with the fem software ansys, the maximum deformation of the work roll was calculated, and the curve of the gap adopting the least - squares method was fitted, which set the base of the further calculation of load - gap shape

    摘要以四輥軋機的彎輥系統為研究對象，利用有限元分析軟體ansys研究彎輥力和輥間接觸應力引起工作輥形狀的變化，計算工作輥彎曲的最大變形量，並用最小二乘法對輥縫曲線進行擬合，為進一步計算有載輥縫形狀提供可靠的理論依據。
  9. Large area of spalling accured on the work layer of high - crcentrifugal cast iron roll after heat treatment

    高鉻離心復合鑄鐵軋輥輥身工作層在熱處理后發生大面積剝落。
  10. The results indicated that discontinuity of micro structure of work layer caused by in. homogeneous distribution of chemical composition, different pattern of carbide, mhomogeneity of hardness lead to large area of spalling and frther scrapping of roll

    結果表明，化學成分的不均勻分佈，造成軋輥輥身工作層組織不連續、碳化拘形態各異使輥身工作層硬度不均勻，產生大面積剝落，最終導致軋輥報廢。
  11. It ' s the advantage of jmfc to apply the centrifugal casting technology to the small size of compound rolls, which characteristics are as follows : combining high hardness, anti - wear, impact and breakage resistance : spun cast the shell by proper charging of alloys and use high strength and impact ductility material as core

    將離心澆鑄工藝用於小型復合軋輥的製造，是金環廠的優勢，採用該工藝的軋輥具有以下特點：兼得高硬度耐磨損與抗沖擊抗斷裂性能：按耐磨性和硬度要求，將合金科學配比，溶解澆鑄成輥身的工作層，再採用高強度抗沖擊的材料澆鑄輥頸和輥芯，冶金結合，兩者兼得。
  12. The configuration of conventional backup and work rolls for revamped 1700 tandem cold rolling mill at wisco was proved unreasonable by systematical test as the cause of work roll edges contact during thin strip rolling and unsatisfactory flatness of product

    摘要通過現場跟蹤測試和生產實踐發現武鋼1700冷連軋機組「酸軋聯機」改造工程中存在常規凸度輥形配置方案不合理，由此引起了薄規格軋制的工作輥「壓肩」現象和軋制過程欠穩定導致成品板形質量欠佳等問題。
  13. Considering different microstructures and properties of metal of hardened layer and the core of back - up roller, the distributions of shear stress below surface and the contact stress between work roller and back - up roller of a four - high - mill were simulated with nonlinear fem

    摘要考慮軋輥表面淬硬層與其心部金屬材料組織性能的差別，採用非線性有限元方法對四輥軋機的工作輥與支撐輥間接觸應力及輥內剪應力分佈進行模擬，並將模擬結果與傳統強度校核方法進行了對比分析，研究了軋輥淬硬層厚度對輥間接觸應力的影響規律。
  14. Abstract : the present paper introduces the history of development, operating principle and characteristics of the rolling mill with axial shifting roll as well as its application in the country, analyzes the feature of the shape control for the currently most broadly applied hc rolling mill and discusses in detail the setting up of the roll system

    文摘:介紹了軋輥軸向移動軋機的發展過程、工作原理、形式特點以及在國內的應用情況，分析了目前應用最普遍的hc系列軋機的板形控制特性，並對輥系配置進行了深入的探討。
  15. The work principle and identity of the press with cone - shaped roll have been introduced with expounding use of plc to control the production of such machine of which the technology and control have been based as design of the hardware and software of control system

    摘要介紹了軸向軋制的雙錐輥輾壓機的工作原理和特性，闡述應用可編程式控制制器控制雙錐輥軸向軋機的生產，並且針對其工藝和控制要求，從硬體和軟體進行了控制系統的設計。
  16. Crush fast, seal entire journey, improve the working environment, adopt the stainless steel roller, use the special tooth shape and special processing craft, enhance the smashing quality

    粉碎速度快，全程封閉，改善工作環境，採用不銹鋼制軋輥，採用特殊齒形和特殊加工工藝，提高粉碎質量。
  17. Compares with the same centripetal ball bearing, has the big radial direction load bearing capacity, mainly is suitable for the cold hot - rolling mill, working roll support rolls and so on cogging mill

    與相同的向心球軸承相比，有較大的徑向負荷承載能力，主要適用於冷熱軋機，開坯機等工作輥支承輥。
  18. General specifications of forged steel working rolls for cold rolling

    鍛鋼冷軋工作輥通用技術條件
  19. Double - freguency quenching unit and heat treatment process for cold - rolling work rolls

    共昌冷軋工作輥雙頻淬火設備及工藝技術探討
  20. When work rolls become worn the roughness is diminishing creating slippage in the roll bite at higher speeds

    工作輥磨損后，粗糙度遞減導致在較高軋制速度下進料（咬入帶卷）時產生滑移。
分享友人
分享到 Line

分享到臉書