弧焊電源 的英文怎麼說

中文拼音 [húhàndiànyuán]
弧焊電源 英文
arc welding electrical supply
  • 弧 : 名詞1. [數學] （圓周的任意一段） arc2. （古代指弓） bow
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 源 : 名詞1. （水流起頭的地方） source （of a river）; fountainhead 2. （來源） source; cause 3. （姓氏） a surname
  • 電源 : source; current source; electric source; power pack; power supply; power source; source of power ...
  1. Arc welding equipment - part 1 : welding power sources

    弧焊設備第1部分：焊接電源
  2. The sources of these internal transients are everyday items, such as air compressors, arc welders, pumps, elevators, switching power supplies and other inductive loads

    這些內部電涌的根源是每天都會使用的設備，如空氣壓縮機，電弧焊接機，泵，電梯，開關電源和其他的感應負載。
  3. Mjc : the sources of these internal transients are everyday items, such as air compressors, arc welders, pumps, elevators, switching power supplies and other inductive loads

    這些內部電涌的根源是每天都會使用的設備，如空氣壓縮機，電弧焊接機，泵，電梯，開關電源和其他的感應負載。
  4. In this paper, it has been studied by the slope - controlled scr rectifier that external characteristic of welder relate to arc digging action and the strong arc force of arc welding power source in manual arc welding formed

    利用一種特製的變結構可控硅整流焊機，研究不同焊機外特性對電弧穿透力的影響；探討了手工電弧焊強電弧力形成機理；並且指出正確設計電源外特性，是獲得較強電弧穿透力的途徑。
  5. Switching welding power source controlled by microcomputer

    微機控制開關式弧焊電源
  6. Arc welding equipment - welding power sources

    電弧焊設備.焊接電源
  7. Standard for arc welding equipment, part 1 : welding power sources

    電弧焊接設備標準.第1部分:焊接電源
  8. In this thesis, a high - frequency variable polarity arc welding power supply was investigated, which consisted of two independent power sources, the variable polarity power supply and the high - frequency pulse one, having advantages both of them

    本文針對鋁合金焊接研製了一種新型電源，所研究的高頻變極性弧焊電源採用雙電源結構，由變極性電源和高頻脈沖電源組成，綜合了兩者的優點。
  9. Arc welding power sources, equipment and accessories - specification for welding cables

    電弧焊電源設備和附件.第4部分:焊接電纜規范
  10. Arc welding equipment - part 6 : limited duty manual metal arc welding power sources

    電弧焊接設備.第6部分:有限工作時間手動金屬弧焊電源
  11. Study on the control circuits of external characteristic and dynamic characteristic of igbt manual metal arc welding inverter

    逆變式手弧焊電源外特性與動特性控制電路研究
  12. Arc welding equipment - limited duty manual metal arc welding power sources

    電弧焊設備.有限任務手動金屬電弧焊電源
  13. Arc welding equipment - part 6 : limited duty manual metal arc welding power sources iec 60974 - 6 : 2003 ; german version en 60974 - 6 : 2003

    電弧焊設備.第6部分:有限工作時間手動金屬弧焊電源
  14. Double forward converter ( dfc ) has many advantages, such as inherent anti - break - though capability, auto clamping the switch voltage etc. regarding the excellent reliability, dfc is one the most widely used topology in the industrial applications, especially for low output voltage area, such as telecommunication energy systems and welding power supply

    雙管正激變換器具有內在抗橋臂直通的優點，能使開關管上的電壓自動箝位在輸入電源電壓。由於其可靠性高，電路設計簡單，因而成為目前在工業中應用最普遍的變換器結構之? ，特別是適合於輸出電壓較低應用場合，比如通信系統中的一次電源和弧焊電源。
  15. Arc welding electric power supply

    電弧焊電源
  16. Arc welding equipment - part 1 : arc welding power sources

    弧焊設備.第1部分:弧焊電源
  17. Development of inverter ac pmig arc welding power source

    逆變弧焊電源的研製
  18. An intelligent co2 arc welding power

    2弧焊電源的研究
  19. Arc welding power

    弧焊電源
  20. Because arc welding inverter is working in the large signal perturbation state, a large - signal simulation model is created

    根據弧焊電源系統工作在大信號擾動狀態下的特點，建立了電源系統的大信號模擬模型。
分享友人
分享到 Line

分享到臉書