彎主支架 的英文怎麼說

中文拼音 [wānzhǔzhījià]
彎主支架 英文
knee mounting with a bent column
  • 彎 : Ⅰ形容詞（彎曲） curved; bent; crooked; flexuous; tortuous Ⅱ動詞1 （使彎曲） curved; bend; flex 2 ...
  • 支 : Ⅰ名詞1 （分支; 支派） branch; offshoot 2 （地支） the twelve earthly branches3 （姓氏） a surname...
  • 架 : Ⅰ名詞1 （用來放置東西或支撐物體等的東西; 架子） frame; rack; shelf; stand 2 （毆打; 爭吵） fight;...
  • 支架 : support; stand; trestle; holder; rack; tressel; spur; sting; husk （hoose）; buck; undercarriage
  1. Some research results are achieved as follows : ( 1 ) layout of lpg supply system and modification of body construction are carried out, and structural analyses of fuel supply bracket are performed. then fuel bottle with single - welding line and valve type specially used for lpg motorcycle is designed and fabricated, and boil - off pressure adjuster and mixing unit of lpg fuel supply are successfully developed

    主要工作和結論如下： （ 1 ）完成了lpg摩托車燃料供給系的總體布置與整車改裝，及其燃料供給系支架與座墊支承的結構分析和抗彎加固；設計和製造加工出組合閥式、單焊縫結構的lpg摩托車專用鋼瓶；實現汽化調壓器與混合器的良好匹配及長縫式等比例式空氣與燃氣混合器的成功開發。
  2. Finally, the thesis primarily sets up the internal force model of the supporting structure system in the bi - arch tunnel, namely, the distribution model of the surrounding rock ' s pressure, the internal force model of the steel framework and the axial force model of the anchor bolt, and these results can have the guiding significance to the design and construction of the similar tunnel engineering

    最後，結合有限元的理論計算及現場實測數據的分析，初步建立了雙連拱隧道支護結構體系的內力模型，即：圍巖土壓力模型、初期支護鋼拱架內力（主要為軸力和彎矩）模型以及錨桿軸力模型。充分理解和闡述了構件的工作狀態，對今後類似隧道工程的設計和施工具有一定的指導意義。
  3. Cross - check the main roof truss roof installation quality of the surface is not perpendicular to the vertical center two blocks ; roof surface pressure chord of the roof truss vertical bending side, we must ensure that such errors do not exceed the allowable deviation to ensure roof stability and comply with the design requirements of the state by force

    屋架安裝質量主要檢查屋架跨中對兩支座中心豎向面的不垂直度;屋架受壓弦桿對屋架豎向面的側面彎曲，必須保證上述偏差不超過允許偏差，以保證屋架符合設計受力狀態及整體穩定要求
  4. Topics covered include : static equilibrium, force resultants, support conditions, analysis of determinate planar structures ( beams, trusses, frames ), stresses and strains in structural elements, states of stress ( shear, bending, torsion ), statically indeterminate systems, displacements and deformations, introduction to matrix methods, elastic stability, and approximate methods

    主題包含了：靜力平衡、合力、支承條件、靜定平面結構（梁、桁架、構架）分析，結構構件之應力與應變，應力狀態（剪力、彎矩、扭力） ，靜不定系統，變位與變形，矩陣方法介紹，彈性穩定及近似值解法。
分享友人
分享到 Line

分享到臉書