扭緊螺栓 的英文怎麼說
中文拼音 [niǔjǐnluóshuān]
扭緊螺栓
英文
wring bolt- 扭 : 動詞1 (掉轉; 轉動) turn round 2 (擰; 旋轉) twist; wrench 3 (擰傷) sprain; wrench 4 (走路時...
- 緊 : Ⅰ形容詞1 (物體受到幾方面的拉力或壓力以後呈現的緊張狀態) taut; tight 2 (物體受外力作用變得固定...
- 螺 : 1. [動物學] (軟體動物) spiral shell; snail; conch 2. (螺旋形的指紋) whorl (in fingerprint)
- 栓 : 名詞1. (可開關的機件) bolt; plug 2. (塞子) stopper; cork
- 螺栓 : bolt; screw bolt; threaded bolt
-
Combines with a concrete subject, this paper, composed of seven chapers, makes a deep analysis on theory and experiment of key bolt fastening of engine. the first chapter presents the theory of tightening technology of the available bolt the second chapter gives a narrating about tighten technology availably in survey. pointing that the nature of torque control is axis preload
本文結合一具體課題,第一章敘述了可控螺栓擰緊技術的理論,第二章綜述了可控擰緊技術,提出了扭矩控制研究的實質是控制螺栓的軸向預緊力。Metal construction. jointing by means of bolts with controlled tightening. calibration of torque wrenches
金屬結構.可控拉緊螺栓連接.扭力扳手校準After proper operation has been verified, tighten all bolts using the crossover method. recommended tightening torques pattern is listed below
在檢驗操作能夠正常進行后,在採用交叉法緊固所有螺栓。推薦的緊固扭矩模式如下所示。Chapter three makes clear the importance of preload, and deals with the theories on the relationship between preload and torque, angle and extension of the bolt from various aspects
第三章由扭矩控制的實質? ?預緊力,點明了預緊力的重要性,預緊力與擰緊力矩、螺母轉角、螺栓伸長的關系,對其進行了理論方面的研究和探討。Mechanical properties of fasteners - torsional test and minimum torques for bolts and screws with nominal diameters 1mm to 10mm
緊固件機械性能螺栓與螺釘的扭矩試驗和破壞扭矩公稱直徑1 10mmMechanical properties of fasteners - torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm
緊固件機械性能.標稱直徑為1mm到10mm的螺栓和螺釘的扭轉試驗和最小扭矩Mechanical properties of fasteners. part 7 : torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm
緊固件機械性能.第7部分:公稱直徑1 - 10mm的螺栓和螺釘的扭力試驗和最小扭矩Mechanical properties of fasteners part 7 : torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm
緊固件的機械特性.第7部分:扭力試驗和標稱直徑為1mm - 10mm的螺栓和螺釘的最小扭矩Replace body bolts and torque evenly to 70 ft. / lbs
重新放置閥體螺栓,並且用70英尺/磅的扭矩均勻的旋緊。分享友人