拉出強度 的英文怎麼說

中文拼音 [lāchūqiángdù]
拉出強度 英文
pull off strength
  • 拉 : 拉構詞成分。
  • 強 : 強形容詞（強硬不屈;固執） stubborn; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 拉出 : pull-out; exhaustion; unreeve; haul out; drag out拉出輥 pull-out rolls; 拉出器 puller
  1. The fatigue behavior of strength, stiffness, and deformation of concrete is analysed systematically. the fatigue equation is established. the empirical expressions of the total longitudinal strain and the elastic modulus are given, and the relationships between the increasing rate of the total second - stage strain and the decreasing rate of the elastic modulus with the cyclic number are obtained

    系統地分析了砼抗拉、拉-壓疲勞強度、剛度、變形規律；建立了相應的s - n關系，提出了縱向總應變、彈性模量的經驗公式，及其第二階段總應變增長率、彈性模量衰減率分別與疲勞壽命的關系式。
  2. The whole tension strength of steel fiber reinforced self - stressing concrete is a combination of tension strength of matrix and the self - stress value ; the strain of knee point is defined to 500 10 ^ ( - 6 ), and a formula for stress of knee point is suggested

    鋼纖維自應力混凝土抗拉強度為混凝土基體的抗拉強度與自應力值之和；曲線下降段拐點的應變定義為500 10 ^ （ - 6 ） ，並提出拐點應力計算公式。
  3. In this research, the lime - fly - ash bound macadam was joined with steel fibers, glass fibers and polypropylene fibers with the contents of the lime, the fly ash and the macadam fixed in lab tests. the study focuses mainly on the split strength, compression strength, and modulus of compressive resilience and shrinkage property of the lime - fly - ash bound macadam enhanced by different kinds of fibers. based on the test, a detail theoretical analysis was made on the relation of mechanical property, dry shr inkage with the variety and the quantity of fibers, applying the theories of strength, dry shrinkage and the methods of statistics, curve mimesis and variance analysis

    本論文主要是研究在同一種二灰碎石混合料（石灰、粉煤灰、集料的含量及比例相同）中分別摻入不同數量的鋼纖維、玻璃纖維、聚丙烯纖維，通過室內試驗對其抗拉強度、抗壓強度、抗壓回彈模量和乾燥收縮性能與纖維摻量和纖維品種之間的關系加以分析和研究，並在此基礎上根據二灰碎石強度形成機理、乾燥收縮機理和數理統計、曲線擬合、方差分析的方法分析纖維品種和纖維數量對二灰碎石的力學性能和乾燥收縮性能的影響，最後得出纖維對二灰碎石的強度、抗壓回彈模量、乾燥收縮有很顯著的影響，並提出了相應的建議。
  4. Lastly, with the fatigue equation, the paper establishes the fatigue stress coefficient which is used in the load stress calculation for lean concrete as undersurface of cement concrete pavement, and the structure coefficient of flexural tensile strength which is used in the flexural stress check for lean concrete as base of asphalt pavement

    利用得出的疲勞方程，建立貧混凝土作為水泥混凝土路面下面層荷載應力計算的疲勞應力系數，以及作為瀝青路面基層時，進行層底彎拉應力驗算的彎拉強度結構系數。
  5. ( 2 ) another interesting phenomenon is founded that the center of south asia high in the upper level of troposphere is stabile and nearly motionless during the processes of the westward extension of western pacific subtropical high, but its eastern ridge strengthens and extends eastward remarkably because of the anticyclone moves westward over the southeast japan, which may lead to the westward extension of subtropical high in the middle level of troposphere. ( 3 ) in the low level of troposphere, the north australia cold air activity plays an important role on the westward extension of subtropical high

    （ 2 ）本文在研究副高西伸過程中指出，高層200hpa上日本東南部的高壓併入南亞高壓，導致南亞高壓脊的增強發展，對低層500hpa上副高的加強、西伸可能起到引導的作用；同時，對流層低層850hpa上孟加拉灣槽在副高西伸過程中加深，並在西伸脊點到達最西點的前4天強度達到最強，這為預報西太平洋副高的活動提供了參考。
  6. 4. the choice reference of medium belt material is came up with : with higher compress intensity, pull intensity and bend fatigue intensity, with middle or low elastic modulus, besides fine heat - resistant, wearable, oil - fast, water - fast anti - impactive capabilities

    4 、提出並分析了介質帶材料的合理選擇原則：壓縮強度、拉伸強度和彎曲疲勞強度高和韌性好的中低彈性模量復合材料，此外還需具有良好的耐熱、耐油耐水性、耐磨性、抗沖擊性、耐候性等。
  7. When fillings is other materials ( unprocessed montmorillonite, powder coal ash, co - composite of powder coal ash and organo - montmorillonite, co - composite ofcarbonizing calcium and organo - montmorillonite ) in the binder and content of organo - montmorillonite in the binder is five percent decided by tensile - shear experiment, tensile - shear strength of binder is up to tiptop ; at the same time, this paper carries out abrasion experiment, and, by comparison, concludes abrasion property of coating is optimum when content of organo - montmorillonite in the binder coating is five percent, and observes abrasion sample under set

    當膠粘劑中填料為其它物質（未處理蒙脫土、粉煤灰、粉煤灰和有機化蒙脫土共復合、碳化鈣和有機化蒙脫土共復合）時，通過拉伸剪切試驗確定膠粘劑中有機化蒙脫土含量為5時，膠粘劑的拉伸剪切強度最高；同時進行了沖蝕磨損試驗，通過比較得出，當膠粘劑塗層中有機化蒙脫土含量達到5時，塗層的耐沖蝕磨損性能最佳，並對沖蝕磨損試樣在掃描電子顯微鏡（ set ）上進行觀察。
  8. This subject is to combine the steel fiber reinforced concrete with the lightweight aggregate concrete to form a steel fiber reinforced lightweight aggregate ( haydite ) concrete, which owns the advantages of high toughness of steel fiber reinforced concrete and the light weight of lightweight aggregate concrete. in order to get the main character and mechanical property parameter of strength and deformation of steel fiber reinforced lightweight aggregate concrete, we do the experiments of cubic compressive strength, splitting - tensile strength, bending strength, elastic modulus and axial compressive strength and summarize the influence laws to the relation of mechanical performance of steel fiber reinforced lightweight aggregate and the quantity of steel fiber

    鋼纖維輕骨料混凝土兼有鋼纖維混凝土的韌性高和輕骨料混凝土質量輕的優點，為了掌握這種新型材料的主要特徵和強度、變形等力學性能，本文進行了鋼纖維輕骨料混凝土的立方體抗壓強度、軸心抗壓強度、劈裂抗拉強度、抗折強度和彈性模量等試驗研究，總結出鋼纖維摻量對鋼纖維輕骨料混凝土的力學性能的影響規律。
  9. The relations, such as the tensile strength of extrusion products to extrusion ratio and contents of powder strengthen materials, the practical load of powder extrusion to contents of powder strengthen materials, extrusion ratio and extrusion velocity, were given by this dissertation

    論文給出了實驗過程中擠壓製品的抗拉強度與擠壓比、顆粒增強材料含量之間的關系，粉末擠壓所需的實際擠壓力與顆粒增強材料含量、擠壓比、擠壓速度之間的關系等。
  10. Test results show that the steel fiber in concrete have more effectiveness on improving the splitting tensile strength and the flexural strength in the early age than after its hardening ; the flexural modulus of elasticity of sfrc are higher than the plain concrete at different ages while their compressive modulus of elasticity are almost the same. it ' s also shown that, similar to the plain concrete, the early - age loading decreases the strengths of sfrc, but, with the increase of the contents of the steel fiber things are getting better, especially for the splitting tensile strength and the flexural strength

    試驗結果表明：與性能穩定之後相比，在混凝土中摻入鋼纖維對它的早期劈裂抗拉強度和抗折強度有尤為顯著的提高作用；對各齡期的受壓彈性模量影響不大，而對提高抗折彈性模量有一定的效果；與素混凝土試件相同，在早期（強度達到28天強度的85前）對鋼纖維混凝土試件施加荷載會對它的各種強度產生一定的不利影響，但是摻入鋼纖維可以減輕這種不利影響，尤其對劈裂抗拉強度和抗折強度作用突出，並且含纖率越高，效果越明顯。
  11. Citing five - meter - high nanfei river rubber dam in hefei, one of the highest double - anchor water rubber dam in china as an example, while deeply analyzing some representative rubber dam projects in china, the article theoretically exploits the relationships among some technical parameters such as anti - pull intensity, internal pressure ratio, circum - oriented relative extending rate, etc. also has the author brought up his own opinion on rubber dam design & calculation theory, which is of high theoretical and applicative value for parameter optimization and combination of water rubber dam with a height of above 3. 5 meters. it also helps when building over - five - meter - high rubber dam using seamless rubber dam and rubber dam with steel wire as its frame. this article also exploits safety measures for designing & building rubber dam in navigation areas

    本文以充水式雙錨固橡膠壩目前國內最高（壩高5m ）之一的合肥市南淝河橡膠壩工程為例，並在對全國目前已建橡膠壩代表工程進行深入分析的基礎上，對壩袋的抗拉強度、內壓比、環向相對伸長率等技術參數之間的關系進行了理論探討和研究，並對橡膠壩設計計算理論提出了自己的見解和看法，對指導設計壩高3 . 5m以上的充水式橡膠壩技術參數的優化組合具有重要的理論和應用價值，特別對應用無搭接縫橡膠壩、鋼絲網骨架橡膠壩建造壩高大於5m的橡膠壩具有指導意義。
  12. Firstly, for the system of moulding board and support frame in construction the side pressure and screws are analyzed. the material and structure form of support frame are discussed. the design of support frame uses the method of limited state, and also it analyses the integer stability, part stability, and single stability, and then proposes the load analysis of multi - level support frame

    首先，針對轉換層梁模體系及支撐架施工，重點分析了轉換層結構現澆混凝土對模板側壓力值及模板對拉螺桿的計算；討論了轉換層支撐體系的形式及構造，詳細論述了基於極限狀態設計的支撐架計算方法，包括縱橫向水平桿的強度驗算、立桿的整體穩定性、局部穩定性、單肢桿件穩定性等驗算，並提出了多層支撐架的施工荷載計算方法。
  13. It puts forward an effective deep drawing technology about the alloy board with low - alloy and high - strength so that the properties of motor combustion chamber case satisfy with the needs of system

    從而提出了一套行之有效的低合金高強度合金板的拉深工藝，確保發動機燃燒室殼體的質量滿足系統性能要求。
  14. In other words, the process of analyzing relaxation zone related to one safety factor can also be regarded as the process of searching potential slide surface related to the same safety factor. elastic wedge model is used for analysis of relaxation zone of cutting homogeneous slope. on the basis of elastic plane - strain theory, the relaxation zone can be calculated according to mohr - coulomb or drucker - prager law and single tension intensity principle which are both related to one safety factor after three - dimensional stress field of the cutting slope is got

    提出均質邊坡開挖鬆弛區可以用彈性理論中的楔形體理論分析，在平面應變問題的基礎上得到開挖坡體的三向應力場之後，可運用考慮安全儲備后的強度條件（主要為摩爾?庫侖或德魯克?布拉格強度準則和單軸抗拉強度準則）解析坡體分步開挖過程中的鬆弛區范圍，給出了具體的計算步驟，並通過算例較詳細地說明了操作過程。
  15. Second, many mechanical properties are tested, for example, tensile strength and tensile modulus, flexural strength and flextural modulus and impact strength. by the analysis of the tensile stress - strain curves and the flexural stress - strain curves, the results are as follows : 1 ) the voluminal content of fibre of composite making by vacuum assistant resin injection is more than other composites. 2 ) the mechanical properties of the needlepunching nonwoven fabric reinforced polymer composite are superior to these of the calendering nonwoven fabric reinforced polymer composite

    首先，採用不同的增強材料（針刺非織造布和熱軋非織造布） 、不同的基體材料（ 961樹脂和306樹脂）和不同的成型工藝方法（手糊法、真空袋法和真空輔助成型法）製造出了一系列非織造布增強復合材料，然後對它們的拉伸強度、拉仲彈性模量、彎曲強度、彎曲彈性模量和沖擊強度等力學性能進行了測試，並分析了它們的拉伸載荷? ?位移曲線和彎曲載荷? ?位移曲線，結果表明真空輔助成型工藝能大大提高纖維的體積含量；針刺非織造布增強復合材料各項力學性能優于熱軋非織造布增強復合材料。
  16. Condoms will age as time goes by, resulting in impairment of the tenacity. exposure to intense heat and light will also accelerate ageing of the rubber, thus weakening the pulling force and affecting its overall function. do not buy condoms displayed under decorative light and sunlight in the shop

    安全套在出廠之後，會隨著時間而出現老化現象，影響其韌力，高熱或強光也會令橡膠加速老化，拉力強度變弱，以致影響其功能，在選購時，如產品存放于射燈或陽光照射的地方，便不應購買，安全套應放置在陰涼的地方。
  17. The paper focuses on the processing technique of wood flour - recycle polystyrene composite, and assesses the effects of wood flour contents, coupling agent contents and the rotate speeds of extruder on water uptake, tension strength, bending strength and dynamic mechanical properties. the results can be shown as follows : with the increasing of wood flour, composites gain higher water uptake but lower dynamic mechanical properties, the storage moduli ( e " ) and glass transition temperature ( tg ) decrease

    較系統地研究了木粉含量、偶聯劑添加量和雙螺桿擠出機的螺桿轉速等主要擠出工藝參數對復合材料的吸水性能、拉伸強度、彎曲強度、動態機械性質（存儲模量e和損耗正切角tan ）的影響規律，初步確定了適宜工藝條件，主要結論是： 1 ）木粉含量的增加使得復合材料的吸水性能增加，動態機械性質下降。
  18. Cnx coating provided a comparable to or better surface than dlc for the normal cellular attachment, growth and morp hology. compared with dlc, cnx coating also exhibited higher hardness, lower coefficient of friction, lower roughness, and lower corrosion, which obviously contributed to more sp3c structure and indicated a longer wear and corrosion life for cnx coating

    本試驗中所制備的碳氮薄膜和類金剛石薄膜都具有很好的光潔度，但cn膜表面的針狀突起少於dlc膜表面，整體更加勻實光滑，三種薄膜的硬度和拉伸強度都很高，顯示出良好的機械性能和很低的摩擦系數。
  19. The results of the experiment are as follows : the bend strength, bend modulus, stiffness and toughness of the mortar layer will be improved when add 30 % fsmf to resin. the axis tensile strength, stiffness, hardness and weariessness of winding layer will be improved when add 25 % ~ 30 % fsmf to resin

    提出了應用設想並進行了實驗研究，結果表明:在樹脂中加入30 %的fsmf ，可提高夾砂層的彎曲強度、彎曲模量、剛度和韌性;在樹脂中加入25吠屍30 %的fsmf ，可提高纏繞層的軸向拉伸強度、剛度、硬度和耐磨性，降低成本。
  20. With 20 % coupling agent, composites with 40 % and 50 % wood - flour content gain better storage moduli ( e " ) than these without coupling agent, and composites with 40 % and 50 % wood powder content attain the increments in tension and bending strength of 10 % and 40 % respectively, the rotate speeds of extruder affect the mixing of wood powder, coupling agent and polystyrene

    3 ）雙螺桿擠出機的轉速影響著木粉偶聯劑和聚苯乙烯的均勻混合程度。研究發現，雙螺桿轉速為40rpm時，復合材料性質好於其它轉速。 4 ）木粉含量為40 ，偶聯劑含量為20的復合材料其力學強度（拉伸強度為40 . 22mpa ，彎曲強度為76 . 192mpa ）和存儲模量明顯高於其他工藝條件的復合材料。
分享友人
分享到 Line

分享到臉書