拉力強度 的英文怎麼說

中文拼音 [lālìqiángdù]
拉力強度 英文
intensity of tension
  • 拉 : 拉構詞成分。
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 強 : 強形容詞（強硬不屈;固執） stubborn; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 拉力 : pulling; pulling force; thrust; traction; tension拉力表 draw bar [pull] dynamometer; 拉力測定儀 [...
  1. With the filling of diabase, the mechanical properties of the composite increased first and then decreased with a top tensile strength of 56. 5mpa and a top impact strength of 70. 1mpa. these illuminated that the diabase fiber reinforced pvc composites could be used as structure materials

    復合材料的力學性能隨著輝綠巖的增加先升后降，復合材料拉伸強度最高可達56 . 5mpa ，復合材料沖擊強度最高可達70 . 1mpa ，說明輝綠巖纖維增強pvc復合材料作結構材料使用。
  2. The results from x - ray diffraction demonstrated that pp / mmtome was a fully intercalated nanocomposite, pp / mmtom and pp / ommt were partly intercalated nanocomposites, but the intercalation effect of pp / mmtom nanocomposite was better ; the crystallization characteristics of pure pp and pp / mmt nanocomposites were investigated by dsc, waxd and pom. the result of these testing showed that mmt nano - layers acted as nucleating agents for the crystallization of pp, the addition of mmt had effect on the crystallization process, leading the increasing of crystallization temperature crystallization rate and crystallinity, but also the dimension of spherulite reduced. but the formation of pp crystal did n ' t change, the formation of pp crystal in three pp / mmt nanocomposites and pure pp were a - form on the whole ; influences of three sorts of mmt on mechanical properties of pp / mmt nanocomposites were studied, as a result, the addition of mmt comprehensively improved mechanical properties of pp : notched impact strength, tensile strength and flexural properties were all increasing, but the extent of increasing were n ' t large

    通過xrd分析比較這三種pp mmt納米復合材料微觀結構得到， pp mmt _ （ ome ）屬于完全插層， pp mmt _ （ om ）與pp ommt的插層程度相近，但是pp mmt _ （ om ）相對較好；通過對純pp和三種pp mmt納米復合材料的結晶性能研究發現，蒙脫土納米片層對pp結晶產生明顯的異相成核作用，結晶能力增強，使pp的結晶溫度和結晶速率提高，結晶度增加，球晶晶粒細化，但是沒有改變pp的結晶形態，三種pp mmt納米復合材料的結晶形態都屬于晶；通過對pp mmt納米復合材料的力學性能測試得知，蒙脫土的加入全面提高了pp的力學性能，缺口沖擊強度、拉伸強度和彎曲性能都有一定程度的提高，浙江{ _業大學碩十學位論文摘要但是提高幅度都不是很大，不過ommt 、 mmtom和mmtc ） me三種蒙脫土對pp力學性能有著不同的改性作用，其中pp / mmtom最好， pp月邊mto崛次之， pp / ommt最低，這種情況主要是由蒙脫土對pp結晶性能的影響和蒙脫土的納米改性作用造成的。
  3. Intensity resist crushability on unit area n grain

    橫向拉力強度kg
  4. This specially designed machine tests numerous materials, including varieties of shoe soles, tires, rubber hoses, rubber belts, pvc cloth, pvc boards, package films, acrylics, ftp, abs, and eva. products, semi - products or dumbbell specimens are tested for their tensile strength, elongation, tearing, and adhesive stress - strain, peeling, shearing, and adhesion to metal and rubber

    試驗各種材料及鞋、輪胎、橡膠管、三色膠帶、塑膠布、塑膠板、包裝用膜薄膜等成品、半成品啞鈴狀試片之拉力強度、伸長率、撕裂、膠著力、抗拉應力、剝離、剪力、橡膠與金屬之粘合力。
  5. The mechanical tests result showed that when the mmt content is 2 % and the compatilizer content is 15 %, the pmc has best mechanical property. the izod impact strength is 16. 45 kj / m2 and the tensile strength is 35. 77 mpa, increasing 280 % and 4. 3 %, compared with pure pp. the pom photo indicated that the o - mmt can reduce the scale of spherical crystal of pp

    以am為插層劑得到的聚丙烯蒙脫土納米復合材料中，蒙脫土保持剝離狀態，但力學性能不理想，當土含量為0 . 5時，材料的沖擊強度為9 . 58kj m ~ 2 ，拉伸強度為25 . 5mpa 。
  6. Nonpolar polypropylene has bad compatibility with mmt even after organic modification to mmt. so polypropylene ( pp ) grafting acrylic acid was produced by the suspension grafting method as compatilizer. as pp / mmt nanocomposites prepared from htab modified mmt as concerned, the interlayer spacing of mmt is 4. 61nm, 4. 2nm and 4. 09nm respectively when the mmt content is 1 %, 2 % and 3 %. so, the abtained nanocomposites has intercalated structure

    當土含量為2 ，相容劑用量為15時力學性能最好，缺口沖擊強度和拉伸強度分別達到16 . 45kj m ~ 2和35 . 77mpa ，分別比純pp增加了280和4 . 3 ，蒙脫土的加入起到了增韌和增強的雙重作用。
  7. To measure the tensile strength of hot rolled bars, steel wire and weld strength of steel

    測試熱軋鋼筋、鋼絲和扁鋼抗拉力強度和焊接強度
  8. Results of study show that inception voltage of electrical tree, breakdown voltage, environmental stress cracking, tensile strength and elongation at break of low density polyethylene are improved after grafting

    研究結果表明：接枝聚硅氧烷后，改性的低密度聚乙烯的樹枝引發示性電壓、擊穿場強、耐環境應力開裂性、拉伸強度及斷裂伸長率都得到提高。
  9. Abstract : this paper researches into the complex adhesive ， which was mainly made by the soy protein isolate ( spi ) and polyvinyl alcohol or polyvinyl acetate. different composition of protein and polymers can perform different characters, together with other ingredients. the factors, which are related to the first adhesive strength and adhesive strength, are mainly studied and discussed. the first adhesive strength of the complex adhesive is related to the content of spi, and the adhesive strength is related to the content of the complex adhesive. on the basis of the researching, we can make the plant fibre box for food in the future

    文摘:對大豆分離蛋白?聚乙烯醇、大豆分離蛋白?白乳膠復合膠粘劑進行了研究，採用不同混合比例及添加其他助劑，得到較好性能和可生物降解的復合膠粘劑，為製造一次性植物纖維快餐盒打下基礎.主要研究了影響這種復合膠粘劑粘接木塊的初粘力（剪切和拉伸強度）和粘接強度的因素，實驗表明： 9 . 2 %濃度的大豆分離蛋白的初粘力（剪切和拉伸強度）優於10 %濃度的聚乙烯醇膠和33 %濃度的白乳膠；大豆分離蛋白復合膠粘劑的初粘力主要與大豆分離蛋白含量有關，其最終粘接強度與膠液固含量正相關
  10. Diameter tolerance and tensile strength

    公差及拉力強度
  11. Transverse tensile strength kg

    橫向拉力強度kg
  12. Annealed tensile strength

    退火后的拉力強度
  13. Vertical tensile strength

    豎向拉力強度kg
  14. Splitting tensile strength

    張裂拉力強度
  15. Household sewing - machines ; testing of loss of tensile strength of needle thread by sewing

    家用縫紉機.第9部分:採用縫紉法對針線拉力強度損失的
  16. Unbound and hydraulically bound mixtures - test method for the determination of the indirect tensile strength of hydraulically bound mixtures

    鬆散的和液壓粘合的混合料.測定液壓粘合混合料非直接拉力強度的試驗方法
  17. Equally obvious is that the force applied to move the plates must be capable, at least occasionally, of exceeding the tensile strength of the plate material and of breaking a larger plate into two smaller ones

    同樣顯而易見的是，用於移動板塊的力必須能超過板塊物質的拉力強度，並且能將一個較大的板塊分成兩個小板塊，至少有時會是這樣的。
  18. In other words, the process of analyzing relaxation zone related to one safety factor can also be regarded as the process of searching potential slide surface related to the same safety factor. elastic wedge model is used for analysis of relaxation zone of cutting homogeneous slope. on the basis of elastic plane - strain theory, the relaxation zone can be calculated according to mohr - coulomb or drucker - prager law and single tension intensity principle which are both related to one safety factor after three - dimensional stress field of the cutting slope is got

    提出均質邊坡開挖鬆弛區可以用彈性理論中的楔形體理論分析，在平面應變問題的基礎上得到開挖坡體的三向應力場之後，可運用考慮安全儲備后的強度條件（主要為摩爾?庫侖或德魯克?布拉格強度準則和單軸抗拉強度準則）解析坡體分步開挖過程中的鬆弛區范圍，給出了具體的計算步驟，並通過算例較詳細地說明了操作過程。
  19. Condoms will age as time goes by, resulting in impairment of the tenacity. exposure to intense heat and light will also accelerate ageing of the rubber, thus weakening the pulling force and affecting its overall function. do not buy condoms displayed under decorative light and sunlight in the shop

    安全套在出廠之後，會隨著時間而出現老化現象，影響其韌力，高熱或強光也會令橡膠加速老化，拉力強度變弱，以致影響其功能，在選購時，如產品存放于射燈或陽光照射的地方，便不應購買，安全套應放置在陰涼的地方。
  20. At present, at present, we have all our production lines automatically, and the annual output up to 80, 000, 000 pcs ; among which the nylon zipper is very popular in the market because of the tensile strength however, the plastic zipper make itself become as the mainstream in market because of its various colors and safety coefficient

    目前擁有皆為全自動化的生產線；其中尼龍拉鏈的拉力強度高，廣受好評，而塑鋼拉鏈由於色澤變化多，安全系數更高，已成為市埸主流。
分享友人
分享到 Line

分享到臉書