按序編製程序 的英文怎麼說

中文拼音 [ànxùbiānzhìchéngxù]
按序編製程序 英文
sequential programming
  • 按 : Ⅰ動詞1 （用手或手指壓） press; push down 2 （壓住; 擱下） leave aside; shelve 3 （抑制） restrain...
  • 編 : Ⅰ動詞1 （編織） weave; plait; braid 2 （組織; 排列） make a list; arrange in a list; organize; gr...
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 程序 : 1 （進行次序） order; procedure; course; sequence; schedule; ground rule; routing process 2 [自動...
  1. Licensee shall not decompile, reverse engineer, disassemble or otherwise reduce the software to a human perceivable form, or to modify, network, rent, lease, loan, distribute, or create derivative works based upon the software or the documentation in whole or in part

    許可證持有人亦不得逆轉編譯、設計、匯編等程序，又或令軟體的程式轉換成可理解的信息，又或修改、聯接、出借、出租、暫借、分發或按此軟體及其附帶文件的全部或部分內容衍生製造其他程式。
  2. And several conceptions, such as stability of waves and absorptivity, are given, which made it possible to evaluate the effectiveness of the wave - maker quantificationally the result of a series of experiments which using the new method certify that the methods are effective to resolve the problem of multi - reflection in wave flume

    使用這些概念和方法可以定量分析造波機的吸收效果。按照本文提出的方法編寫了造波機控製程序，並進行了吸收式造波實驗，結果證明這種方法能夠有效地解決波浪實驗過程中的多次反射的問題。
  3. After being got by calculating, the position of welding seam will be real - time transmited to controller of abb robot through serial port communicatioa the controller of abb robot with multi - cpu is equipped with multi - task operate system. a movement - controlling program is made by rpid language that is abb robot programming language. the program will real - time read the data from serial port and adjust the welding torch according to data read from serial port

    得到了焊縫的中心位置后，就要通過串口通信（ rs232 ）實時傳送到abb的機器人的控制器， abb機器人控制器功能強大帶有多個cpu ，其中裝有多任務的操作系統，用rapid語言編一個運動控製程序，實時讀串口數據，然後按照讀出的數據調整焊槍的位置。
  4. In addition, with the development of the hydraulic technology, the experiment table may be in step with the developing need of the hydraulic teaching by applying the enlarged module of the plc and ameliorating the pc control program

    不僅如此，而且隨著液壓技術的發展，該實驗臺可以通過增加可編程式控制制器的開關量和模擬量擴展模塊，並且完善相應的上位機數據採集控製程序，增加相應的控制柜上所需按鈕，滿足不斷發展的液壓教學需要。
  5. With the siemens plc s7 - 300 and the corresponding programming software step7, that helps in control software programming, the proportioning system meets the requirements of automatic proportioning, weighing, loading and weight compensating. the design work uses wincc, that is also a product from siemens, to configure the supervisory software, realizing the real - time data - logging, supervising and controlling, as well as various visual hmi with windows features such as real - time weighing, record checking, alarming, dynamic simulation

    該項目採用的是德國siemens公司的s7 - 300系列plc ，運用與之相配的step7編程軟體，通過stl和lad兩種編程語言編制了下位機的控製程序，從而使該槽下配料系統可以按要求自動完成配料、稱量、裝料全過程，並自動實現稱量補償。
  6. Third, evaluate mmds ( multipoint microwave distribute system ) project of youli company in material operable procedure and method. finally, three case of technology innovation investments is reconstruct, and the methods used in the cases is appraised

    第三，按照copeland和antikarov的方法和步驟，利用二項網格法，通過編製程序對優立公司的mmds項目進行了定價。
  7. The communication between the can - bus node and the control computer was established using lab view and c language. the gui ( graphics user interface ) was designed with labview and the kernel driver, which is written in c language. experiments show that the testing node can communicate with the control computer properly

    2 、在can總線規范的基礎上，按照整體結構進行了can總線測試節點硬體和軟體設計，實測表明can總線測試節點軟硬體聯合工作穩定， 3 、運用labview編程語言，結合c內核程序設計了上位機數據管理與控製程序，實現了上位機與下位機的通信。
  8. To a construction being built with determinate groundsill, the paper first assumes it with enough height, then devides its back exterior into several shelter bars. there will be borderlines on the shelter bars corresponding to every window being measured. in the paper it takes the number of the window whose borderline is kept by the shelter bar as the gene of the chromosome

    對一地基確定的待建建築物，開始時假定其足夠高，將其後表面分割成若干遮擋條，每個待測窗體在各遮擋條上都有對應的臨界線，將每個遮擋條所取的臨界線對應的窗體號作為染色體的基因進行編碼，按照繪制的遺傳演算法流程圖，通過vc語言編製成相應程序，求解出每個遮擋條應保留的高度，從而得到整幢建築物的高度和其最大容積。
分享友人
分享到 Line

分享到臉書