振動模製 的英文怎麼說
中文拼音 [zhèndòngmózhì]
振動模製
英文
jolt molding-
3. as to vehicle - bridge system coupling vibration, this difficulty in engineering industry, it was abstractly summarized in this thesis, and introduce a method to establish and resolve equations about such coupling vibration, bring forward a flow chart to write correlative software ; with the help of ansys, make out some work about preparatory simulation, so as to research basic point of chicle - bridge system coupling vibration
3 、對車橋耦合振動這一業內的難點進行了理論上的分析，引入了一種建立和求解車橋耦合振動系統方程的較為典型的方法，提出了一份自行編製程序的流程簡圖；借用ansys軟體對該橋做了車橋耦合振動的初步模擬計算，探索車橋共振的基本特點。A new method for measuring the vibration of shadow mask without touch by detecting the light density with reflection type optical fiber sensor is presented. the measurement system based on the new method is designed to make the vibration measurement easier working, faster calculating, and get more precise results. it is an important measurement and analysis tool to improve the performance of shadow mask and display quality of cpt
本文提出了基於單光纖光強度反射法的非接觸式微振動測量系統的原理，並設計製造了該測試系統，探索出了簡單方便可靠的測量方法，能夠準確客觀地反映蔭罩振動的各項參數（各振動模的振動頻率、振幅、衰減時間） ，實現了測試裝置的簡便化和測試過程的自動化，為cpt張緊式蔭罩系統的性能改進與顯示質量的提高提供了有效的測試分析手段。In order to make the sensitivity of 2 - demension accelerometer along the two main arbors almost identical, symmetric four - beam structure that embeds a double - sides interdigitated differential capacitive with puckered beam in two directions was used as sensitive component. in addition, the differential capacitive accelerometer fabricated by bulky silicon micromechanical technique has high sensitivity, wide measurement scope, less nonlinear error, and simple converting circuit. then, the structure parameters of the sensitive component were calculated and stimulated, which results in a set of the optimized structure design parameters, main fabrication procedure and several key fabrication technology
為使二維振動傳感器在兩主軸方向的靈敏度大致相同，敏感元件採用高度對稱的四梁結構，其中每個軸向上均採用帶折疊梁的雙側叉指電容結構，採用體硅微機械工藝製作的高深寬比叉指電容式敏感元件，具有高靈敏度、寬量程、非線性誤差小、外圍電路簡單等優點;對設計的敏感元件結構參數進行了計算，並利用有限元法進行了模擬分析，根據模擬結果得出了優化參數;在確定敏感結構的基礎上，研究了敏感元件採用體硅微機械加工工藝製作的工藝流程和關鍵工藝技術;對敏感晶元內部的c - v介面電路進行了原理設計與分析，利用差動測量技術得到由振動引起的微小電容變化量，經c - v介面電路進行相位調制處理，然後通過解調輸出與加速度成正比的電壓信號。Efficient to lose fat, adopt micro - computer technology to make the vibration strongly effect on the abdomen, which part with most fat of the body. inner - desighed strong motor effect on the organism directly. unique auto change direction mode, makes the full dimension vibration of the organism
迴旋塑身腰帶運用微電腦技術，將強效振動裝置直接作用於脂肪最為集中的腹背部，內置的強有力的電動機直接作用於肌體，產品獨有的大幅度的水平移動自動變換方向運動模式，使肌體大范圍全方位共振，同時加快身體血液循環，微電腦控製程序可自動逐步增強產品運動力度，使用過程中自動轉換運動方向。At last, a set of online monitoring of hydropower unit vibration and analyzing system is developed, including ipc, a / d cards, vibration sensors and correlative modules
最後研製了一套由工控機、 a d卡、振動、擺度傳感器及相關模塊組成的振動在線監測與分析系統。Based on the advanced embedded computer and network technology along with the embedded operational system such as windowsce, the instruments can gather many functions such as transmitting and measurement, compensatory computation, signal analysis and processing into one instrument. in this paper a portable instrument for vibration measurement with embedded computer system was discussed. based on windowsce real - time operation system the software of this instrument was designed and developed with evc computer language
本文基於目前流行的便攜式儀器的核心技術? ? windowsce ，設計開發了應用於現場設備振動測量分析的的便攜式測振儀表，針對現場特點和實際要求，對于測振儀的硬體系統進行了規劃設計，並重點對于儀器軟體進行開發，在windowsce平臺下，利用evc語言開發研製了儀器的應用軟體，實現了包括信號採集、分析、顯示、數據存儲和通信功能的軟體系統；並對該軟體進行了計算機模擬調試。There is an important step which between the simulation in theory and the debugging in industry locale must to be done, the step is electric simulation ( it ’ s also mean half - real simulation )
同時，在理論模擬和實際現場調試之間，還有一個重要的環節就是電模擬模擬（即半實物模擬） 。設計、製作液壓振動系統的電模擬模型模擬系統也是工作的重要內容之一。6. a new method that adopt small exciter emulation to the dual - shaker vibration system and research the numerical electric current phase synchronous controller, thus
6 .提出採用小型激振器模擬並聯雙振動臺進行數字式電流相位同步控制器試驗研究的方法，從而降低同步控制器在研製階段的試驗成本，並且避免同步控制器的不確定性給振動臺造成損傷。Hydraulic pound, vibrate, noise and cavitation are the main difficult problems in water hydraulic valves, and finite element numerical analysis is proved to be an effective computational method, so numerical simulation and visualizing research on the flow field in water hydraulic valves by applying finite volume method is very important
水壓閥中的液壓沖擊、振動、噪聲以及水壓閥中的氣蝕是研製水壓閥存在的主要難題，而有限體積數值計算方法又被證實是一種可行而有效的流場計演算法，因此應用有限體積法對水壓閥閥道內流場進行數值模擬和可視化研究，是非常有意義，也是非常重要的。Primary experimental results indicate that the apparatus is capable of modeling the vortex - induced vibrations of pipeline and the sand scour around the pipeline in typical ocean environments
初步實驗結果表明文中研製的實驗模擬裝置能夠模擬典型海洋環境下海底管道的渦激振動和管道周圍海床沖刷等問題。The metal mold casting processes including assembly metallic die design and manufacture were studied by an example of concrete vibrator ' s wiring bale
以混凝土振動器接線包為例，對其金屬型鑄造工藝進行了研究，主要包括組合金屬型模具的設計與製造。Based on the results of previous researchers, the following instigations have been carried out in this paper : ( 1 ) employing a reasonable local resonance model which can accurately embody the heat - generation behavior due to resonance and vibration - heat mode in delaminated region, the dynamic response and temperature distribution in the small delamination region of a laminated beam are formulated. influence of the excitation frequency on the temperature gradient formation is analyzed numerically, and several meaningful conclusions are drawn. ( 2 ) for laminated plates with delaminations, due to complexity of the analytical solution, the finite element method is employed to analyze their temperature distributions and satisfactory results are also obtained
本文在前人研究的基礎上，對此方法進行了進一步的探討，主要做了以下的工作： （ 1 ）選取合理的、能夠準確反映由共振而產生熱量的行為的局部響應模型，以及合理的振動熱模式，推導了一維層合梁小脫層區域的振動響應及梁的溫度分佈，並編製程序計算了該層合梁在激勵一段時間后的溫度分佈趨勢，分析了激勵頻率對溫度梯度形成的影響，得到了一些有意義的結論； （ 2 ）對於二維層合板，由於解析解的形式異常復雜，本文採用有限元計算軟體對其溫度分佈進行了分析，也得到了較為滿意的結果。Extruded concrete curb technology was introduced in 20th congress icold held in beijing in year 2000, this method draw more attention for its improving the compaction of transition material, excellent performance of slope protection, and convenient construction. this extruded concrete curb technology was developed in ita dam construction in brazil, the ita method consists of building and extruded concrete curb by using an extruding machine before the construction of a layer of the transition material, then spread and level the transition material in layers inside the curb, and compact the layer by vib ' ratory roller horizontally
巴西工程界在埃塔（ ita ）面板堆石壩建設中，借鑒道路園林工程中道沿機的擠壓滑模原理，創造性使用邊墻施工法，在每填築一層墊層料之前，用擠壓式邊墻機製作出一個半透水混凝土小墻，然後在其內側按設計鋪填壩料，用振動碾平面碾壓，合格后重復以上工序。Standard practice for making roller - compacted concrete in cylinder molds using a vibrating table
使用振動臺在筒模中製作碾實混凝土的標準實施規范Matlab procedure is coded to compute the far - field sound pressure levels of the shell excited by radial point force. the influences of modal truncation, stringers, bulkheads and damping on the shell ' s far - field sound pressure are analyzed, laying down the basis for accurate analysis of the sound radiation from fluid - loaded reinforced double cylindrical shells
本文用matlab編製程序求解了單層殼在徑向激勵力作用下的遠場聲壓級，分析了模態截斷數、縱骨、艙壁板、結構阻尼等因素對殼體遠場輻射聲壓的影響，為準確計算加筋雙層殼在水下振動和聲輻射特性奠定了基礎。And a post - liquefaction test method has been put forward, in which the cyclic loading and the static loading courses are both controlled by stress mode. this method reflects the in - situ conditions well and truly, and a lot of tests have been done using this method. in these tests the effects of confining pressure, relative density, liquefaction severity etc. have been thoroughly investigated
主要工作內容如下：參與研製了振動扭剪全自動多功能三軸儀，並利用其獨特試驗功能設計了一套飽水砂土液化后特性的試驗方法，試驗過程中模擬地震作用的動加載過程及模擬大變形發生的靜加載過程均採用應力控制的方式進行，試驗方法跟現場條件更為接近並用該試驗方法對相對密實度、固結壓力、液化度等對液化后變形特性的影響進行了研究。In this paper, the modularized configuration of windows ce operating system and the procedure of driver development are disserted, real - time and embedded performance are analyzed, characteristics of application program development are summarized. what ' s more, wince operating system based on pcm - 3350 is configured, driver of data acquisition board and application software are programmed
本文論述了wince操作系統的模塊化體系結構和驅動程序開發的流程，分析了wince的實時性和嵌入性，總結了wince下應用程序開發的特點；並且實現了基於研華pcm - 3350操作系統的定製、振動信號採集卡驅動程序的開發和振動分析軟體的設計與編程實現。At the same tune, the paper analyses and discusses the control projects of the above parts. as for the hardware of the control system, on principle of reliability and considering the badly working condition of the vibratory roller, the paper chooses the special controller sp ecializing in the realm of construction machinery ' s control system in order to insure the reliability of the control system and simplify it. about the control quality of the system, the paper establishes the mathematical modes of the frequency modulation system and the amplitude modulation system, analyses the irrationality of the amplitude modulation project, puts forward to apply proportional - integral - differential controller ( pid controller ) to the traveling system and frequency modulation system
作為控制系統的方案設計的基礎，本文首先對影響壓實效果的振動參數進行了分析；然後針對智能振動壓路機的功能要求，將控制系統分為壓實參數的自動和手動控制、行走控制、轉向和蟹行控制以及智能灑水控制等幾個部分，對各部分的控制方案進行了分析對比和論證；在控制系統硬體設計方面，以可靠性為原則，考慮到振動壓路機的惡劣工況，選擇了專用於工程機械控制領域的專用控制器，使系統的硬體設計得以可靠性保障和簡化；針對控制系統控製品質問題，建立了調頻和調幅系統的控制模型，對調幅系統的控制不合理性進行了分析，提出採用pid控制器對行走和調頻系統進行校正；在軟體設計方面，對各個控制部分進行了軟體編程流程圖設計。Previously the vibration line marker adopts the equipment and materials imported from japan for application. now shenyang liyuan company has successfully developed the self - contained protruding vibration line marker. the product ' s quality has reached the international standard like the same rank of the product around the world through a large amount of application for vibration lines
振動標線過去全採用日本進口設備和材料進行施劃，現在沈陽立元公司成功研製出自走式凸起振動標線機，使用該機進行了大規模振動標線施工，產品質量穩定，達到國際同類產品的水平。Based on the theory analysis, computer simulations and experiment researches, the problem according to any angular vibration curve of crankshaft to diagnose the power of each cylinder of i. c. engine, are completely solved and the concerned equipment is developed in this paper
作者通過大量理論分析、模擬計算和實驗研究，首次全面系統地解決了根據內燃機曲軸某一測點的角振動曲線診斷內燃機各缸作功狀況的診斷方法和相關診斷測試設備研製等問題。分享友人