振幅校正 的英文怎麼說

中文拼音 [zhènfújiàozhēng]
振幅校正 英文
amplitude correction
  • 振 : 動詞1. （搖動; 揮動） shake; flap; wield 2. （奮起） brace up; rise with force and spirit
  • 幅 : Ⅰ名詞1. （布帛、呢絨等的寬度） width of cloth 2. （泛指寬度） width; size 3. （姓氏） a surname Ⅱ量詞（用於布帛、呢絨、圖畫等）
  • 校 : 校名詞1. （學校） school 2. （校官） field officer3. （姓氏） a surname
  • 正 : 正名詞（正月） the first month of the lunar year; the first moon
  • 校正 : check; correction; adjust; revise; proofread and correct; rectify; calibrate; make true; master c...
  1. The clues and techniques to improve the resolution of data processing are 1 ) removing the affection of near surface factors on data acquisition, including static correction and noise eliminating technique etc, 2 ) broadening the frequency band of pre - stack seismic data, including amplitude compensation and pre - stack deconvolution etc, 3 ) improving s / n ratio of high frequency and weak reflection signals through multiple coverage with high precision velocity analysis, residual static correction and high - order nmo, raising " dead line of high frequency reflection ", and 4 ) identifying post stack effective reflection frequency band, enhancing dominant frequency and so on

    主要包括：消除近地表因素對資料採集的影響，包括靜校正和噪音壓制技術等；疊前拓寬地震資料領帶，包括振幅補償和疊前反褶積技術等；藉助高精度速度分析、剩餘靜校正和高次項nmo技術，通過多次覆蓋疊加，消除資料中隨機噪聲干擾、提高資料信噪比，尤其是高頻端反射信息的信噪比，改善高頻反射和弱反射信號信噪比，提高「高頻反射死亡線」 ；疊後有限反射頗帶識別、抬高優勢頻率等。
  2. At the same tune, the paper analyses and discusses the control projects of the above parts. as for the hardware of the control system, on principle of reliability and considering the badly working condition of the vibratory roller, the paper chooses the special controller sp ecializing in the realm of construction machinery ' s control system in order to insure the reliability of the control system and simplify it. about the control quality of the system, the paper establishes the mathematical modes of the frequency modulation system and the amplitude modulation system, analyses the irrationality of the amplitude modulation project, puts forward to apply proportional - integral - differential controller ( pid controller ) to the traveling system and frequency modulation system

    作為控制系統的方案設計的基礎，本文首先對影響壓實效果的振動參數進行了分析；然後針對智能振動壓路機的功能要求，將控制系統分為壓實參數的自動和手動控制、行走控制、轉向和蟹行控制以及智能灑水控制等幾個部分，對各部分的控制方案進行了分析對比和論證；在控制系統硬體設計方面，以可靠性為原則，考慮到振動壓路機的惡劣工況，選擇了專用於工程機械控制領域的專用控制器，使系統的硬體設計得以可靠性保障和簡化；針對控制系統控製品質問題，建立了調頻和調幅系統的控制模型，對調幅系統的控制不合理性進行了分析，提出採用pid控制器對行走和調頻系統進行校正；在軟體設計方面，對各個控制部分進行了軟體編程流程圖設計。
  3. For the amplitude - frequency response at the self - oscillation frequency is one, a method to calculate the dynamic accuracy and the index of the servo system is provided, by comparing them, the scheme to design the verifying unit is presented

    利用伺服系統在自振蕩頻率點的幅頻特性為1這一特點，將輸入信號頻率、幅值、系統的自振蕩狀態和系統的參數聯系起來，構建了伺服系統動態精度的計算公式和指標估算經驗公式，並根據兩者的關系提出動態精度校正方案。
  4. On the basis of the analysis of the hypothesis in surface - consistent model, the conjugate gradient method is applied to decompose the seismic record in time domain in terms of the surface - consistent precondition and model

    摘要通過對地表一致性數學物理模型的前提條件進行剖析，合理地確定了反射振幅一致性校正模型，並依據該模型及其實現條件提出使用共軛梯度方法在時間域對地震記錄進行譜分解處理。
分享友人
分享到 Line

分享到臉書