掃氣時間 的英文怎麼說

中文拼音 [sǎoqìshíjiān]
掃氣時間 英文
scavenging period
  • 掃 : 掃構詞成分。
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 時 : shí］Ⅰ名1 （比較長的一段時間）time; times; days:當時at that time; in those days; 古時 ancient tim...
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 時間 : time; hour; 北京時間十九點整19 hours beijing time; 上課時間school hours; 時間與空間 time and spac...
  1. In this thesis, the oxygen sensitive materials and glucose sensitive materials had been developed by thermo - polymerization method including carrier covalence method and carrier covalence - cross linking method, and the properties had been investigated using the detection experiment of oxygen and spectrophotometer, at the mean time, the applications of oxygen sensitive materials in fiber optical gaseous oxygen sensor and fiber optical dis solved oxygen sensor, and that of biology sensitive materials in fiber optical dextrose sensor had been studied in this paper. major content of this work includes five aspects as follows : ( 1 ). oxygen sensitive materials had been prepared by carrier covalence method, and the preparation mechanism of the materials had been investigated by fi - ir, sem, and the detection experiment of oxygen

    本論文主要包括以下五個方面的內容： （ 1 ）載體共價法制備氧敏感材料：通過紅外光譜、掃描電鏡圖譜和氧測試實驗探討該氧敏感材料的制備機理，通過氧測試實驗評價該氧敏感材料的氧敏感性和穩定性，同時研究了各種因素對該氧敏感材料性能的影響（ 2 ）載體共價?交聯法制備氧敏感材料：通過紅外光譜、掃描電鏡圖譜和氧測試實驗探討該氧敏感材料的制備機理，通過氧測試實驗和分光光度計評價該氧敏感材料的氧敏感性和穩定性，同時研究了各種因素對該氧敏感材料性能的影響（ 3 ）氧敏感材料在光纖氣態氧傳感器中的應用：該傳感器的響應時間為10s ，檢測下限為5ppm ，檢測精度為0 . 5 ，具有較好的重復性和穩定性，遲滯較小，使用壽命至少為1年，適合各種環境下氣態氧濃度的檢測。
  2. The primary theory of absorption and desorption was also explained. the effects of primary process parameters, such as hydrogen pressure, time and temperature on the magnetic properties of ndfeb have been researched. the structure and magnetic properties have been analyzed by means of optical metallographic microscopy, scanning electronic microscopy, x - ray diffraction analysis, infrared oxygen detector and magnetic properties measurement

    本文設計了燒結ndfeb的氫爆制粉設備，對設備調試以及使用過程中出現的主要問題進行了簡要的說明，提出了一系列解決方法；闡述了吸氫、脫氫的基本原理；研究了氫氣壓力、通氫時間、氫爆溫度等基本工藝參數對磁性能的影響；利用金相顯微鏡和掃描電子顯微鏡， x射線衍射分析，紅外線測氧分析及綜合磁性測量儀等手段分析了材料的組織結構和磁性能。
  3. After ca. 20 minutes ( regeneration time of the drier ) and when the operating temperature is attained on the residual ozone eliminator, the ozat ? cfs begins to flush

    大概20分鐘（乾燥器的再生時間）后並且尾氣破壞器的溫度達到時，打開增壓泵開始運行，打開臭氧發生器電源對臭氧發生器進行吹掃。
  4. The relationship between sputtering conditions and the depositional speed shows : with working pressure 1. 2 pa, sputtering power 180w, the depositional speed of tio2 thin film is 40nm / h, and increases with the increasing of sputtering power. it can be also founded that the depositional speed is nearly proportional to the working pressure : within the range of 0. 3pa to 1. 6pa, the depositional speed increases linearly with the increase of ar pressure. with the enhancement of the substrate ' s temperature of sputtering or annealing, the resulted thin films show a tendency of decreasing in thickness, and increasing in refractivity

    本實驗是採用磁控濺射方法，在不同的溫度下制備了tio _ 2薄膜，並對薄膜進行了不同溫度和時間的退火處理，通過原子力顯微鏡（ afm ） 、 x射線衍射（ xrd ） 、掃描電鏡（ sem ）等檢測手段對薄膜的表面形貌和組成結構進行了分析，結果如下： （ 1 ）濺射工藝條件與薄膜沉積速度的關系表明：採用1 . 2pa工作氣壓， 180w的射頻功率tio _ 2薄膜的沉積速率為40nm h ，並隨射頻功率的增加而提高，呈近似的線性關系，在0 . 3pa 1 . 6pa氣壓范圍中，氬氣壓強升高沉積速率迅速增加，濺射溫度提高和退火處理能使薄膜的厚度減小和折射率提高。
分享友人
分享到 Line

分享到臉書