排汽閥 的英文怎麼說

中文拼音 [bèiqìfá]
排汽閥 英文
blowdown valve
  • 排 : 排構詞成分。
  • 汽 : 名詞1. （由液體或某些固體變成的氣體） vapour2. （水蒸氣） steam
  • 閥 : 名詞1 （指在某方面有支配勢力的人物或家族） established house or power group; a powerful person or...
  1. The company takes advantage of advanced dcs control system, high efficient float valve tray technology, high efficient energy - saving exchange techniques, fcc catalytic cracking double riser, two - generator regeneration process, polypropylene with loop reactor process and refining and blending process of high - number gasoline, etc. to ensure providing the users with high - tech qualified products

    公司採用先進的dcs控制系統，高效的浮閥塔盤技術，高效節能交換技術， fcc催化裂化雙提升管、兩器再生工藝，環管聚丙烯工藝，高排號汽油精製調和工藝等，確保高科技合格產品送至用戶手中。
  2. The rundown of stripper bottom product is by level control acting on the fractionator furnace pass control valves

    汽提塔底產品的排出由液位控制，該液位控制調控分餾塔加熱爐通道控制閥。
  3. The factory is specialized in the manufacture of the whole set of testing equipment fo gas - vase ( do not sew, fuse, liquefied petroleum gas, natural gas etc. spirit bottle ), various air infuses set, remitting to flow row and to infuse tongs ; the stainless steel is four fluorine soft tubes, the industrial air ( the pack ) gathers to pack, modernizing industrial factory premises concentration to provide spirit system and assisting a piece : decompression machine, safe valve, allotment box ; and standard air, hybrid air, special kind air, high install craft device purely and gaseously ; the automation cuts over, going together with to compare to equip automatically ; various air valve door and accessories, spirit bottle enclosure ; the low temperature equipments liquid pump ; vaporize a machine ; the low temperature closes valve ; the ripples takes care of to wait a series product

    本廠專業設計生產製造各種氣瓶檢驗成套設備（無縫，溶解，乙炔，液化石油氣，天然氣等氣瓶） ，各種氣體充灌臺，匯流排及充灌夾具;不銹鋼四氟軟管，工業氣體（充裝）集裝箱，現代化工業廠房集中供氣系統及輔件:減壓器，安全閥，分配箱;以及標準氣體，混合氣體，特種氣體，高純氣體的配置工藝裝置;自動化切換，自動配比裝置;各種氣體閥門及配件，氣瓶附件;低溫設備液體泵;汽化器;低溫截止閥;波紋管等系列產品
  4. Cylinder cock valve

    汽缸排水操縱閥
  5. Cylinder drain valve

    汽缸自動排水閥
  6. Methods for determination of discharge capacity of automatic steam traps

    自動凝汽閥排放量的測定方法
  7. Paved secondary containment, waste water collection and biological treatment systems for pollution prevention. pressurised fire water system including dual diesel driven high capacity pumps with automatic tart on demand, and monitors in all operating areas

    時，閥門打開向火炬泄放氣體，火炬處設有水封、阻火器和電點火系統，蒸汽在此系統完全燃燒后達到環保要求的排放標準。
  8. Iso 7842 - 88 automatic steam traps ; determination of discharge capacity ; test methods iso 7842 : 1988 ; german version en 27842 : 1991

    自動凝汽閥.排流量的測定.試驗方法
  9. The lid of this sterilizer is installed with safety valve, exhausting valve, exhausting valve which can keep safety

    滅菌器蓋上裝有安全閥、放汽閥和壓力表，能有效釋放過高壓力，確保安全可靠。放氣閥尾部備有金屬軟管，使排放冷空氣合理方便。
  10. The titanium alloy valve is more superior than ordinary steel valve in lighter, smaller expansion coefficient, improves the tightness in inletting and exhausting, helps in complete combustion, and at the same time reduces noise, friction, oil consumption, vibration, and gas waste

    鈦合金汽門比一般鋼閥材質的產品更輕化、膨脹系數小，于進、排氣時可提升它的氣密動作，幫助完全燃燒，同時減少噪音、摩擦、油耗、震動及廢氣。
  11. Standard specification for steam traps and drains

    蒸汽疏水閥和排水管
  12. When the system pressure drops to the return pressure, the security valve will be closed and stop discharging, in the way of which the pipelines and equipments of the steam system will be protected

    當系統運行壓力降低至安全閥的回座壓力時，主蒸汽安全閥自行關閉，停止排放，從而對主蒸汽系統的管道和設備起安全保護作用。
  13. According to bernoulli theorem, kinetic energy and potential energy change due to the thermokinetic differences of steam and conden sation water, and action valve plate starts and stops to choke air and drain water

    圓盤式疏水閥是根據伯努力熱動力原理，利用蒸汽和凝結水通過閥孔時流速和何種產生變化的不同熱力學性質，驅動閥片開關閥門，從而達到阻汽排水。
  14. When the system pressure goes up to the value that will open the security valve, the main steam security valve will be released all by itself, discharge the excessive steam in the system and lower down the system pressure

    當系統運行壓力上升至安全閥的開啟壓力時，主蒸汽安全閥自行打開，排放主蒸汽系統中的蒸汽，使系統壓力降低。
  15. Theory and experiment study of variable displacement control valve in automotive air conditioning compressors

    汽車空調壓縮機變排量控制閥理論與實驗研究
  16. When the condensation of water increases, the bucket loses buoyancy and makes the machinery reversely seal to generate differential pressure, the main valve opens and obtains large displacement, steam equipment prompt starts to maximize the thermal efficiency of steam equipment

    當凝結水量增大時，吊桶失去浮力使得機構反向密封而產生壓差，主閥開啟而獲得大排量，用汽設備迅速啟動，最大限度地發揮出用汽設備的熱效率。
  17. The condensation heat - exchange characteristic of a separate - type heat - pipe was studied on a 1 : 1 model. the heat pipe is heated by electricity, and working fluid is distilled water, and it is cooled by air. the experimental results show that, ( 1 ) when charging liquid ratio is 45 %, condensation heat - exchange coefficient reaches to maxium ; ( 2 ) when there is not non - condensing gas, the coeffcient decreases a little with the increase of vapour pressure, and it decreases by 9. 5 % when the pressure increases from 0. 16mpa to 0. 36mpa ; ( 3 ) when there is non - condensing gas, the coefficient decreases a little, but when the gas is discharged by an exhaust value, it can be improved, when the volume content of the gas is 2. 5 %, it can increased by 22 % ; ( 4 ) the effect of the non - condensing gas on the coefficient decreases with the increase of the pressure, and when the volume content of the gas is 5 % and the pressure increases from 0. 16mpa to 0. 36mpa, the coefficient increases by 6 %. the relative curves are given between condensation heat - exchange coefficient and air flowrate, charging liquid ratio and vapour pressure

    建立了空氣冷卻實驗臺，熱管的加熱方式為電加熱，工質為蒸餾水.在1 1模型上對分離式熱管管內凝結換熱特性、不凝性氣體對凝結換熱的影響及不凝性氣體的擴散規律進行了試驗，得出分離式熱管有一最佳充液率，其值為45 %左右；凝結換熱系數隨著蒸汽壓力的增加略有降低，在實驗的壓力范圍內，降低了9 . 5 % ；不凝性氣體對分離式熱管的凝結換熱僅影響冷凝段下部較小部分，通過排氣閥排出不凝性氣體可有效地改善冷凝段下部的凝結換熱；隨著壓力的增加，不凝性氣體對分離式熱管冷凝段的影響減少.這些結論可用於分離式熱管換熱器的工程設計和控制
  18. Abstract : the condensation heat - exchange characteristic of a separate - type heat - pipe was studied on a 1 : 1 model. the heat pipe is heated by electricity, and working fluid is distilled water, and it is cooled by air. the experimental results show that, ( 1 ) when charging liquid ratio is 45 %, condensation heat - exchange coefficient reaches to maxium ; ( 2 ) when there is not non - condensing gas, the coeffcient decreases a little with the increase of vapour pressure, and it decreases by 9. 5 % when the pressure increases from 0. 16mpa to 0. 36mpa ; ( 3 ) when there is non - condensing gas, the coefficient decreases a little, but when the gas is discharged by an exhaust value, it can be improved, when the volume content of the gas is 2. 5 %, it can increased by 22 % ; ( 4 ) the effect of the non - condensing gas on the coefficient decreases with the increase of the pressure, and when the volume content of the gas is 5 % and the pressure increases from 0. 16mpa to 0. 36mpa, the coefficient increases by 6 %. the relative curves are given between condensation heat - exchange coefficient and air flowrate, charging liquid ratio and vapour pressure

    文摘:建立了空氣冷卻實驗臺，熱管的加熱方式為電加熱，工質為蒸餾水.在1 1模型上對分離式熱管管內凝結換熱特性、不凝性氣體對凝結換熱的影響及不凝性氣體的擴散規律進行了試驗，得出分離式熱管有一最佳充液率，其值為45 %左右；凝結換熱系數隨著蒸汽壓力的增加略有降低，在實驗的壓力范圍內，降低了9 . 5 % ；不凝性氣體對分離式熱管的凝結換熱僅影響冷凝段下部較小部分，通過排氣閥排出不凝性氣體可有效地改善冷凝段下部的凝結換熱；隨著壓力的增加，不凝性氣體對分離式熱管冷凝段的影響減少.這些結論可用於分離式熱管換熱器的工程設計和控制
分享友人
分享到 Line

分享到臉書