接模圈 的英文怎麼說
中文拼音 [jiēmójuān]
接模圈
英文
adaptor ring-
In this paper, thermal evolution history of organic matter of the source rocks and hydrocarbon generation history have been researched by tti method, hydrocarbon migration direction and migration times were probed combining with the area structure development feature ; distribution pattern of the main reservoir intervals on lateral and longitudinal have been predicted by researching on development feature and control factors of the reservoir intervals, the actions of reservoir conditions in hydrocarbon accumulation and bearing also were probed combining with pore evolution feature ; the micro - pore feature of regional cap and direct seal in carboniferous - lower triassic in this area have been determined with micro - capillary pressure curve and intrusive mercury curve ; the prospecting districts have been pointed out combining with the hydro - geologic feature, the potential reservoirs were classified according to trap types in this area, the author attempt to evaluate on the hydrocarbon - bearing condition in the str ata of carboniferous ~ lower triassic from hydrocarbon generation and migration reservoir condition, reserved condition etc, and predict the reservoir types and hydrocarbon - bearing patterns combining with the structure evolution. based on above, the author point out that the central block of chenghu - tuditang synclinorium and the southern block of dangyang synclinorium are the advantageous regions for exploration
本文用tti方法研究了烴源巖有機質的熱演化史和油氣生成史，並結合區內構造發育特徵，探討油氣在區域上的運移方向和在時間上的運移期次；通過對儲集層段的發育特徵和控制因素的研究，預測了本區主要的儲集層段在橫向上和縱向上的分佈規律，並結合孔隙演化特徵，探討儲集條件在油氣聚集成藏中的作用；利用微毛細管壓力曲線法和壓汞法，對石炭系?下三疊統的區域蓋層和直接蓋層的微孔隙特徵進行了定量評價，並結合水文地質分佈特徵，指出有利於油氣保存的地區；根據區內存在的各種圈閉類型，對可能存在的油氣藏進行了分類，並試圖從油氣的生成與運移、儲集條件、保存條件等方面，動態地綜合評價石炭系?下三疊統油氣成藏條件，並結合構造演化特徵，預測其油氣藏類型和成藏模式。This article points out that zhengzhou cantonal space structure should change from single - central, circling expanding to multi - central, separated conglomeration, forming tufty space structure pattern linked by information network, communication network and green belt
認為鄭州市區空間結構應改變以往單中心圈層擴展的發展模式，向多中心、分散組團式轉變，形成以信息網、交通網和綠化帶相互連接的簇團式空間結構模式。The problem about neutral - point - grounding mode is an all - around technical problem which associated with not only power system reliability ， insulation coordination ， electromagnetic interference ， but assault safety 。 in china ， the neutral grounding modes of the 10kv net involved of none grounding, grounding by arc suppressing coils, resistance grounding or reactance grounding in the past 。 with the development of civic power network ， low resistance grounding mode was used to restrain the over voltage, particularly in guangzhou, shanghai ， beijing ， and zhuhai etc. it was reported that the over - voltage level of low resistance grounding mode is lower than that of arc suppressing coil mode, but the operation carried out the other way 。 at substations in guangzhou and shanghai it was found that the low resistance grounding mode is successful 。 but in some areas ， such as zhuhai ， substations grounding with low resistance revealed some problems ， including power supply reliability rapidly dropping ， transmitting line often tripping ； and person safety being threatened 。 so interiorly the grounding mode selection of the 10kv network was disputed, which mainly focused on the fault form of 10kv net grounding, the apply area of suppressing arcing coil grounding mode, power supply reliability level of the two modes, person safety, communication interfere and the workload of maintenance
爭議點主要是在10kv電網接地故障的形式、消弧線圈接地的應用范圍、兩種運行方式供電可靠性的高低、人身安全、通訊干擾和運行維護工作量等諸多方面。 11 17本論文就是針對以電纜為主的城區10kv電網中性點接地方式的選擇問題進行研究。論文首先對10kv電網的中性點運行各種方式進行分析，比較各方式的特點，然後以重慶儲奇門變電站10kv電網的實際參數來建立數值計算模型，在考慮了電網接地電容電流變化、中性點電阻取值大小、接地點接地電阻值變化等多種影響因素的情況下，對中性點經消弧線圈接地和經小電阻接地方式下電網的過電壓水平和接地點短路電流大小進行了數值計算，其計算結果與電科院所作現場試驗進行了比較。The subject of this thesis is to study ironless moving coil linear permanent magnet synchronous motor and the major works in this thesis are summarized as follows : 1 ) two analytical formulas are derived by concentrated current method and distributed current method to determine the magnetic field due to pm, based on the current model of pm. besides, two method ( magnetic charge method and solution by laplace equation method ) are also introduced with comparing their advantages and disadvantages. then the effects of the motor parameters on the flux distribution are discussed
本文對空芯動圈式直線同步電動機進行了深入細致的研究，內容包括： （ 1 ）採用電流模型推導出兩種計算永磁磁極二維氣隙磁場的解析公式（集中電流法、分佈電流法） ，同時介紹了兩種永磁電機氣隙磁場計算方法（磁荷法，直接求解拉氏方程法） ，分析各種方法的優缺點，討論電機參數對氣隙磁密的影響； （ 2 ）介紹了單層同心繞組的布置方式，根據安培定律推導出空芯動圈式直線永磁同步電動機的靜推力計算公式，分析靜態力?位移特性； （ 3 ）建立空芯動圈式直線永磁同步電動機動態模擬模型，模擬不同驅動方式下電動機起動、穩態運行時電磁力、速度、位移的變化情況。However, df pre - processing is not required in a interferometer direction finder. it only makes use of the phase relations or differences of sensors disposed at different position. azimuth and elevation are caculated from the phase differences or displayed directly on a crt drived by the voltage or current from the phase differences
干涉儀測向不必進行測向信號預處理而是直接或間接求取在空間上分開的傳感器上感應電勢之間的相位關系，即干涉相位差，方位角或仰角是直接由干涉相位差計算得到，或將兩基線正交的天線陣的干涉相位差轉化為驅動電壓（電流）分別加到crt陰極顯示器的垂直偏轉線圈和水平偏轉線圈，模擬顯示出來波方位，干涉儀測向為典型的相位測向方法。We got the spatial distribution map of population density by spatial interpolation, in which the population data are distributed on the grids. the results of the distribution of interpolated based on gis is closed to a real population distribution. the combination of the spatial interactive models and a shortest path algorithm for public transit network is analyzed by supermarket ' s accessibility based on pedestrianism and public transit. this methods may be used to investigate potential supermarket ' s locations. the quantitative analysis about the supermarket ' s market area is realized based on trade mode of lashmanan and hansen, which mainly includes spatial distribution of population, traffic accessibility and free competition between different firms
文中應用空間內插技術實現了人口數據空間分佈化，將人口數據通過空間插值分佈於研究區域內，使人口空間分佈更接近實際；應用公交最短路徑演算法及空間相互作用模型實現了基於步行和公交出行的超市可達性，將交通對超市選址的影響定量化，方便了方案的比選；在綜合考慮人口空間分佈、超市交通可達性、現有零售商業競爭態勢的基礎上，基於拉、漢購物模式實現了超市商圈定量分析。Secondly, grounded on the study of the distribution of the high external waterpressure and high geostress and the characteristic of the rock in engineering area, the paper built the elastoplastic fem numerical simulation model, and think over the procedure in tunnels excavation and the history of work of water load, and then get the relations between the different tunnels diameter, different permeability coefficient and depth of the grouting rock and the deformation, stress distribution and plastic range of the surrounding rock and support structure. finally, according to the modern design theory of tunnels construction, the particular design of country rock reinforcement and support structure are researched and presented for diversion tunnels
接著，本文在深入研究工程區高外水壓力及高地應力分佈規律及巖體特性的基礎上，建立起高地應力、高外水壓力作用下隧洞圍巖結構非線性有限元模擬計算模型，然後考慮隧洞的開挖過程、水荷載的作用歷史，通過計算分析得出了不同洞徑、不同的灌漿圈滲透系數和不同的灌漿圈深度以及不同開挖過程與圍巖及支護結構的應力、位移和塑性區的關系。On the basis of analysis of design criterion of shaft washer and housing washer of tandem composite type cylindrical roller thrust bearing, we present a mathematic model for optimal design in accordance with line contact requirement for cylindrical roller and race, design the washers thickness and thickness variation angle by the search algorithm of constrained stochastic direction
摘要在分析串聯組合型推力圓柱滾子軸承軸圈和座圈設計準則的基礎上，按滾子與滾道線接觸要求建立其最優化設計數學模型，採用機械優化設計中的約束隨機方向搜索法計算軸圈和座圈的厚度、厚度變化角。On - line monitoring of hvcb is the precondition of predicting maintenance, is the key element of reliable run, and is the important supplement to the traditional off - line preventive maintenance in fact, the faults are made by hvcb, no matter in number or in times, is over 60 % of total faults so it has determinative importance for improving the reliability of power supply and this can greatly decrease the capital waste used by - dating overhaul in this paper, the inspecting way of hvcb mechanism characteristic is discussed the concept of sub - circuit protector is presented, the scheme that we offered has been combined with sub - circuit integrality monitoring theory, to ensure that it has the two functions as a whole according the shut - off times at rated short circuit given by hvcb manufacturer, the electricity longevity loss can be calculated in each operation, and the remained longevity can be forecast too an indirect way for calculating main touch ' s temperature by using breaker shell temperature, air circumference temperature and breaker ' s heat resistance is improved in this paper, and main touch resistance can be calculated if providing the load current msp430, a new single chip microcomputer made by ti company, is engaged to develop the hardware system of the on - line monitoring device, and special problem brought by the lower supply voltage range of this chip is considered fully
高壓斷路器所造成的事故無論是在次數，還是在事故所造成的停電時間上都占據總量60以上。因此，及時了解斷路器的工作狀態對提高供電可靠性有決定性意義；並可以大大減少盲目定期檢修帶來的資金浪費。本文論述了斷路器機械特性參數監測方法；提出了二次迴路保護器的概念，並將跳、合閘線圈完整性監視和二次迴路保護結合起來，給出具有完整性監視功能的二次迴路保護器實現方案；根據斷路器生產廠家提供的斷路器額定短路電流分斷次數，計算每次分閘對應的觸頭電壽命損耗，預測觸頭電壽命；提出根據斷路器殼體溫度和斷路器周圍空氣溫度結合斷路器熱阻來計算斷路器主觸頭穩態溫升的方法，並根據此時的負荷電流間接計算主觸頭迴路的電阻；在硬體電路設計上，採用美國ti公司最新推出的一種功能強大的單片機msp430 ，並充分考慮該晶元的適用電壓范圍給設計帶來的特殊問題；在通信模塊的設計中，解決了不同工作電壓晶元之間的介面問題，並給出了直接聯接的接線方案。Plastics piping systems - injection - moulded thermoplastics fittings for elastic sealing ring type joints for pressure piping - test method for resistance to a short - term internal pressure without end thrust
塑料管道系統.壓力管道的彈性密封圈式連接件用注模製熱塑塑料性配件.耐無部端推力的快速內壓的試驗方法Pump body : there is a steel flange ring respectively at the connection on both left and right, which are made of die stamped plastic alloy
泵體：左右兩邊連接部分內埋鋼質法蘭圈各一隻模壓塑料合金製成。Through simulating model tests of shield tunnel passing through the yellew river in the diversion project from south to north china, a systematic analysis on the primary factors affecting joint stiffness, including arrangement of joint bolt, thickness of annular packing of bolt, behavior and thickness of cushion material between two tube plates, magnitude of prestressing force of joint bolt and different stressed states at tube plate joint etc., are performed. the study results may provide reference for tube plate design of shield tunnel
通過南水北調穿黃盾構隧道模擬模型試驗，對影響接頭剛度的主要因素即連接螺栓的布置、螺栓墊圈的厚度、管片與管片之間墊層材料的性能和厚度、連接螺栓的預緊力的大小及管片接頭不同的受力狀態進行了系統的分析，為盾構隧道管片設計提供了參考。Abstract : through simulating model tests of shield tunnel passing through the yellew river in the diversion project from south to north china, a systematic analysis on the primary factors affecting joint stiffness, including arrangement of joint bolt, thickness of annular packing of bolt, behavior and thickness of cushion material between two tube plates, magnitude of prestressing force of joint bolt and different stressed states at tube plate joint etc., are performed. the study results may provide reference for tube plate design of shield tunnel
文摘:通過南水北調穿黃盾構隧道模擬模型試驗，對影響接頭剛度的主要因素即連接螺栓的布置、螺栓墊圈的厚度、管片與管片之間墊層材料的性能和厚度、連接螺栓的預緊力的大小及管片接頭不同的受力狀態進行了系統的分析，為盾構隧道管片設計提供了參考。Secondly, methods of improving on probe are investigated in detail : using the electromagnetic shielding effect to decay the direct - coupled magnetic field and using the dual probe to control the energy flow, so as to make the probe to be shorter ; designing 3 - d pick - up coil array to increase detection sensitivity. at last, experiment system is set up to verify the simulation result and the comparing result shows simulation result agrees with experiment result
其次，對改進傳感器性能的幾種方法進行了詳細研究:利用電磁屏蔽效應以衰減在直接路徑上的磁場傳播、採用復式探頭激勵方式以實現能流控制，從而減小傳感器體積，模擬證實這兩種改進方案有效;設計三維周向檢測線圈陣列以提高缺陷檢測靈敏度，模擬結果證實三維探頭的周向靈敏性。And then make out the nonlinear equations from the mathematics models, the results includes : the contact angler, contact distortion and axial distortion of each rolling element in the bearing
求解兩種數學模型的非線性方程組，計算出軸承各滾動體在不同工況下內、外圈接觸角，接觸變形和軸承軸向、徑向位移等。Aerospace series - collars, flanged swage locking, sheartype, in titanium ti - p99002, metric series
航天航空系列. ti - p99002型鈦合金米制系列法蘭連接模壓鎖緊切變型墊圈In recent years, with the large - scale reconstruction of city power system, the scale of power system is continuously expanding, and the power supply network is becoming larger and larger. in addition, the enormous use of cables in city power system increases the current through the grounded capacitor. these lead to more and more instantaneously grounding faults unable to eliminate naturally
近年來，國家對城市電網的大規模改造，使得電網的規模不斷發展，配電網路越來越大，加上城網中大量使用電纜，使接地電容電流大大增加，越來越多的瞬間單相接地故障不能自動消除，為了解決這一問題，我國普遍採用中性點經消弧線圈接地的補償方式。Plastics piping systems. injection - moulded thermoplastics fittings for elastic sealing ring type joints for pressure piping. test method for resistance to a short - term internal pressure without end thrust
塑料管道系統.壓力管道用彈性密封圈型接頭的注模熱塑配件.耐無端推力短暫內壓力性能的試驗方法Differential in series, electronic differentials, complex spring and coil - over, traction control systems, abs systems, 6 wheels cars : this is just a small list of what ' s in the software but you still can ' t see cause the cars we developed for this first incarnation don ' t feature those elements
微分串聯，電子差速器，復雜的春季和線圈接管，牽引力控制系統， abs的系統， 6輪子車：這只是一個小規模的名單什麼的，在軟體，但你還是不能見導致我們的汽車開發這首先體現，並沒有出現這些內容。And this paper structures the emulation model of 10kv transformer substation by utilizing matlab toolbox, emulations the fault course when single - phase ground fault occurs in the small current earth system. and validates the validity of the " gradual identifying law "
並利用matlab工具箱構建10kv變電站模擬模型，對中性點不接地和經消弧線圈接地系統在不同故障情況下的故障過程進行了模擬，進而驗證了「遞進信息法」的正確性。分享友人