接觸半徑 的英文怎麼說

中文拼音 [jiēchùbànjìng]
接觸半徑 英文
contact radius
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 半 : Ⅰ數詞1 （二分之一） half 2 （在 中間的） in the middle; halfway 3 （比喻很少） very little; the l...
  • 徑 : Ⅰ名詞1 （狹窄的道路; 小路） footpath; path; track 2 （達到目的的方法） way; means 3 （直徑的簡稱...
  • 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
  1. In the system, the collimation semiconductor laser - scanned beam scanning two perpendiculars direct of one plane of the measured workpiece at the same time is made. the beams with the dimension information of two perpendiculars direct are processed by the scanning receive system, the high - speed photoelectric transition and electronic data process. two measured results of the diametric directs and ellipse tolerance, etc, parameter, of the turning workpiece on the same plane are obtained by non - contact automatic measurement

    在單向激光掃描檢測技術的基礎之上，提出了一種雙向激光掃描檢測系統，其採用激光掃描檢測技術與特殊光學系統相結合，用準直半導體激光掃描光束對被測工件徑向某一截面的兩個相互垂直方向同時掃描，經掃描接收光學系統、高速光電變換、電子學系統和微機數據處理系統，對將攜帶有垂直方向被測量信息的光束進行處理，實現了回轉體工件同一截面兩個垂直方向的徑向尺寸和橢圓度等參數的非接觸自動測量，解決了同時非接觸測量回轉體零件同一截面兩個徑向尺寸的難題，它具有高速，高精度和非接觸自動測量等特點。
  2. The model describes the force - displacement relationship and the relationship between the contact radius and the displacement

    模型描述了彈塑性點正碰撞的接觸力和變形量、變形量和接觸半徑的關系。
  3. In this paper, wheel - rail rolling contact creepages and creeps of independently rotating wheel are analyzed, the effects of lateral and yaw motions of independently rotating wheel, and the curve radius to creepages of wheel - rail rolling contact are emphasisatically researched. 4

    論文對獨立旋轉車輪的輪軌滾動接觸蠕滑率/力進行了分析，研究了輪對橫移和搖頭運動以及曲線半徑對獨立旋轉車輪輪軌蠕滑率的影響情況。
  4. Among railway line ' s plane design parameter, the minimum radius of curve, transition curve ' s type and length, straight line between two curves, centre - to - centre distance of track are key factors which confine railway to bringing up speed, moreover these factors among maglev railway request even more strict

    由於高速磁懸浮鐵路採用了非接觸式的行車技術，舒適性將得到很好的改善。鐵路線路平面設計參數中，最小曲線半徑、緩和曲線長度、夾直線長度、線間距離是限制列車速度的關鍵因素，高速磁浮鐵路同樣如此。
  5. The optimize design of roller radius is discussed based on the touch intensit y and the thickness of lube film in this paper

    從接觸應力和潤滑油膜厚度兩方面入手，進行滾子半徑的綜合設計。
  6. Roller radius sizes of slave mechanism of cam machin e affect the touch - stress of touch region and the thickness of lube film directl y

    凸輪機構從動件滾子半徑的大小直接影響凸輪副接觸處的接觸應力和潤滑油膜厚度並影響凸輪機構的壽命和運動精度。
  7. Abstract : roller radius sizes of slave mechanism of cam machin e affect the touch - stress of touch region and the thickness of lube film directl y

    文摘:凸輪機構從動件滾子半徑的大小直接影響凸輪副接觸處的接觸應力和潤滑油膜厚度並影響凸輪機構的壽命和運動精度。
  8. Based on the analysis of the stress distribution law in different districts around the self - closed and full - connected arch walling support roadway, the relationship among the limit equilibrium radius and the in - situ rock stress, the physico - mechanical properties and support parameters is obtained. the calculation formula of arch walling width design is put forward so as to provide a theoretical basis for the practical design of support

    在分析自封閉全接觸碹體支護巷硐周圍不同區域應力分佈規律的基礎上，得出了圍巖極限平衡區半徑同巷硐所處的原巖應力，圍巖本身的物理力學性質及碹體支護參數間的相互關系，提出了設計碹體厚度的計算公式，為實際進行支護設計提供了理論依據。
  9. The curvature interference of the gear and the influence of radius of the mill - cutter, axial misalignment, and center distance on meshing are analyzed. based on these analyses, propose two methods to achieve point - contact : to change the radius of the mill - cutter and increase the center distance

    在分析了弧齒線圓柱齒輪的嚙合傳動不產生曲率干涉的條件和刀盤展成半徑、軸線平行度誤差、中心距對嚙合影響的基礎上，提出了點接觸弧齒線圓柱齒輪實現的兩種方案:調整刀盤展成半徑和增大中心距。
  10. The curvature radius was derivated and the contact stress of the three - arc - sect isometric type surface was calculated through the elastic dynamics theory

    應用彈性力學理論，推導出接觸點的曲率半徑，對三弧段等距型面聯接進行接觸應力計算。
分享友人
分享到 Line

分享到臉書