接觸滑塊 的英文怎麼說

中文拼音 [jiēchùgǔkuāi]
接觸滑塊 英文
contact sli er
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 滑 : Ⅰ形容詞1 （光滑; 滑溜） slippery; smooth 2 （油滑; 狡詐） cunning; crafty; slippery Ⅱ動詞（貼著物...
  • 塊 : 名詞（古時佩帶的玉器） penannular jade ring （worn as an ornament in ancient china）
  • 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
  1. Aim of this study was to meet the need for development of tribological parts in pumps. at room temperature tribological properties of different sliding pairs of silicon carbide and alumina - based ceramics were tested using a laboratory tribometer in the ring - on - plate geometry under reciprocating sliding linear contact in different media, such as distilled water, aggressive media and air

    本文針對目前泵用摩擦零部件材料發展的需要，在實驗室摩擦磨損試驗機上研究了按環/塊線接觸方式作往復運動條件下的碳化硅和氧化鋁基陶瓷材料摩擦副在水、化學腐蝕性介質作潤滑劑和無潤滑時室溫下的摩擦磨損特性。
  2. The 3d model of mold is analyzed in 3d fem by using ugh. base on the analyses result, some danger structure of the model have been found and some suggestions of the mold modification are given. since doing a lot of research about the 3d cadvcae technology, a 3dcad system of selecting mold for aluminum material have been developed and the method of analyzing the 3d model is provided in this paper

    然後，為了能真實地模擬實際生產過程，進行鋁與模具鋼在一定表面粗糙度、不同溫度條件、不同潤滑接觸狀態下的最大靜摩擦系數實驗，總結摩擦系數隨溫度變化的規律性和取值范圍；最後，應用ug 17 . 0三維有限元cae模塊進行模具三維力場分析，根據三維有限元的結果分析，對模具危險部分進行預變形的處理和優化，改善模具受力變形的狀況。
  3. After designing oil ditches on the surface of its arc - block, increase friction factor and make sure self - lock which solves above problem. do qualitative analysis to lower pair and one - way overrunning clutch and inner star - wheel - roller overrunning clutch by using self - made lever loader. the experiment shows : on the same condition, the deformation of new overrunning clutch ’ s surface contact with lower pair is smaller than the deformation of roller overrunning clutch ’ s line contact with higher pair and new overrunning clutch ’ s skid angle is smaller

    對低副單向超越離合器的部件進行了加工製造，在超越離合器弧塊表面創新設計加工排油溝，增大摩擦系數，保證實現自鎖，解決了很多離合器工作過程中容易出現無法自鎖的問題;對低副單向超越離合器和內星輪滾柱超越離合器用自製杠桿加載器做了定性分析，實驗表明:相同條件下，新型離合器低副面接觸比滾柱離合器高副線接觸變形小、溜滑角小。
  4. With different clearance value, displacement curves and velocity curves of generalized coordinates as well as slider displacement error curves in a motion period are obtained. these curves are discussed. results show that if manufacturing cost is kept invariableness, in order to improve precision of mould - cuting, fitting precision of joint connecting the crank and coupler has priority to be considered to increase

    採用四階rong - kuta法求解連續接觸模型的動力學方程，得到了一個運動周期內運動副間隙取不同值時，各廣義坐標的位移、速度曲線和滑塊位移誤差曲線，並通過曲線分析，得出了要提高模切機主切機構精度，在相同加工成本條件下，應優先考慮提高曲柄與連桿鉸接處的配合精度的結論。
  5. Considering joint clearances at both ends of the coupler, a continuous contact model is developed by modeling clearance as a massless rigid link. a set of strongly nonlinear equations is obtained by using angle displacement of clearances in kinematic pairs as generalized coordinates. four order rong - kutta method is adopted to solve the dynamical equations of continuous contact model

    考慮曲柄與連桿、連桿與滑塊之間運動副間隙，將運動副間隙看成是一無質量的理想桿，利用連續接觸模型進行建模，採用運動副間隙角作為廣義坐標，得出一組強非線性方程組。
分享友人
分享到 Line

分享到臉書