接觸弧線 的英文怎麼說

中文拼音 [jiēchùhúxiàn]
接觸弧線 英文
contact bow
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 弧 : 名詞1. [數學] （圓周的任意一段） arc2. （古代指弓） bow
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
  • 弧線 : arc弧線運動 movement in a curve
  1. Based on researching the function of every kind of eliminating arc loop, new concept was brought up in this paper, and the protective device for eliminating arc and overvoltage was researched and manufactured. when the arc light connecting the ground emerges, the chip synthesizing controller control the vacuum contacter which can be operated with dividing phase and make its fault phase earthed so that the arc light can be dissolved thoroughly

    本文在研究各種消弧線圈的基礎上，提出全新的概念，研製出了消弧及過電壓保護裝置，該裝置在出現弧光接地時，通過單片機綜合控制器控制一組可以分相操作的真空接觸器，使故障相接地，達到徹底消除弧光的目的。
  2. Firstly, the performance of several kinds of gears that is commonly used in present is analyzed. the sliding coefficients of the involute gear and the cycloidal gear are compared

    論文首先對目前常用的幾種齒輪性能進行了分析，比較了漸開線與擺線齒輪的滑動系數，漸開線與圓弧齒輪的彎曲應力和接觸應力。
  3. After designing oil ditches on the surface of its arc - block, increase friction factor and make sure self - lock which solves above problem. do qualitative analysis to lower pair and one - way overrunning clutch and inner star - wheel - roller overrunning clutch by using self - made lever loader. the experiment shows : on the same condition, the deformation of new overrunning clutch ’ s surface contact with lower pair is smaller than the deformation of roller overrunning clutch ’ s line contact with higher pair and new overrunning clutch ’ s skid angle is smaller

    對低副單向超越離合器的部件進行了加工製造，在超越離合器弧塊表面創新設計加工排油溝，增大摩擦系數，保證實現自鎖，解決了很多離合器工作過程中容易出現無法自鎖的問題;對低副單向超越離合器和內星輪滾柱超越離合器用自製杠桿加載器做了定性分析，實驗表明:相同條件下，新型離合器低副面接觸比滾柱離合器高副線接觸變形小、溜滑角小。
  4. The noise of the high contact ratio gears with the medial sloping contact path is reduced lower than 1 - 2 db, and the noise of the gears with the large sloping contact path is lower ed more

    接觸跡線中度傾斜的高重合度弧齒錐齒輪平均降低噪聲1 2分貝，接觸跡線大傾斜的高重合度弧齒錐齒輪平均降低噪聲2 3分貝。
  5. It consists of two part, the one is hardware : integrating the system of the arc welding robot ' s hardwares and its working principles, separating and extracting the original system ' s control signals, designing the control system openly and its working principles, constructing the structure and principle of the motion card based on dsp, designing the telecontroling teaching box or control panel of touching screen based on usb interface, applying for some software and hardware measures on control system ' s anti - jamming ; the other is software : putting forward the three levels opening software structure model of arc welding, comparing the opening of software structure model between osaca and ours, putting forward the solutions of the pri and communication among the threads of software system ' s modules, using the dll ' s techniques to solve software ' s module design and putting forward the frame codes, bringing forward the path planning software ' s realization by cp + ptp mode, discussing the real time of windows2000 operating system and advancing its solution

    具體包括，硬體部分：弧焊機器人硬體整體系統集成及其工作原理，原系統控制信號的分離和提取，控制系統的開放式設計及組成原理，基於dsp的運動控制卡結構和原理，基於usb介面的觸摸屏式遙控示教盒控制面板的設計，系統抗干擾的軟、硬體措施；軟體部分：提出了弧焊機器人的三層開放式軟體結構模型，軟體結構模型與osaca的模型進行開放性比較，給出軟體系統各模塊線程間優先級和通訊的解決方案，使用動態鏈接庫技術實現軟體模塊化設計並給出了框架代碼，給出了cp + ptp方式的軌跡規劃軟體實現過程， windows2000操作系統實時性問題的討論及解決方案。
  6. The curvature interference of the gear and the influence of radius of the mill - cutter, axial misalignment, and center distance on meshing are analyzed. based on these analyses, propose two methods to achieve point - contact : to change the radius of the mill - cutter and increase the center distance

    在分析了弧齒線圓柱齒輪的嚙合傳動不產生曲率干涉的條件和刀盤展成半徑、軸線平行度誤差、中心距對嚙合影響的基礎上，提出了點接觸弧齒線圓柱齒輪實現的兩種方案:調整刀盤展成半徑和增大中心距。
  7. The calculation of tooth contact stress and the bending stress is discussed. the equation of the bending stress of the gear is developed and the arcuate domino effect is analyzed, comparing with ordinary involute gears

    本文研究了弧齒線圓柱齒輪的齒面接觸應力和彎曲應力的計算方法，提出了計算彎曲應力的公式，對輪齒彎曲效應的影響進行了分析，並與直齒圓柱齒輪進行了比較。
分享友人
分享到 Line

分享到臉書