控制量輸出 的英文怎麼說

中文拼音 [kòngzhìliángshūchū]
控制量輸出 英文
control variable output
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 輸 : Ⅰ動詞1 （運輸; 運送） transport; convey 2 [書面語] （捐獻） contribute money; donate 3 （失敗） l...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  • 輸出 : 1 （從內部送到外部） export 2 [電學] output; outcome; outlet; out fan; fanout; 輸出變壓器 output ...
  1. Pre - data gathering module achieves the collection and communication of sixteen - route temperature signal. speed measuring and controlling module realizes the control of refolw soldering transfer speed by manipulating transducer. on - off outputting module fulfills calefaction control of calefaction tube by solid state relay. above position operator software programs by delphi, and realizes pid parameter automatic timing and no - oversnooting temperature control. software has friendly interface, convenient operation, complete functions

    前置數據採集模塊完成16路溫度信號的採集和通訊；速度測量模塊與速度控制模塊通過控制變頻器來調節迴流焊的傳輸速度；開關量輸出模塊通過固態繼電器對加熱管進行控制；上位機軟體採用delphi編程，實現了pid參數自整定以及無超調的溫度控制。
  2. And the interfaces have analog input, analog output and digital input / output. we have used differently cards, such as pc - 6330d a / d card, pcl - 728 d / a card based isa bus, ipc - 5375 i / o card and so on. in addition, we select micro - stir switches and pressure sensors as sensor elements to inspect the system and choose relays and induction valves to control the bicycle pump and the motor

    總線採用isa內部總線；介面主要有模擬量輸入介面、模擬量輸出介面、開關量輸入輸出介面等，課題分別選用pc - 6330d型a d板卡、基於isa總線的型號為pcl - 728的d a板卡、型號為ipc - 5375的i o板卡；另外，課題選用了微動式行程開關、壓力變送器作為傳感元件檢測系統，選用繼電器、電磁控制換向閥實現對氣缸、電機的控制；採用vc + + 6 . 0編制控制軟體，實現了纖維鋪放技術的計算機控制。
  3. In the proposed method, the controller takes the buffer length as congestion indication, takes sources quality and bandwidth utility as object function so as to learn on line. as the controller outputs, the coding rate for input traffic sources and the corresponding user percentage are used to adjust the cells " arrival rate to the multiplexer buffer. compared with the previous method where cells " arrival rate is tuned only by the encoding rate and the encoding rates for all input traffic sources are regulated in a body, the proposed method guarantee that the quality of cells are optimal while cell loss rate is minimized, which means quality of service is guaranteed

    在該方法中，擁塞控制器以緩沖區大小信元作為擁塞指示，以信源質量和帶寬利用率作為目標函數進行在線學習，控制器輸出包括信源編碼率及其對應的用戶數在全部用戶中所佔的百分比，即根據信源編碼率及對應的用戶百分數調整信源輸入流，從而克服了以往擁塞控制方法中僅僅調整編碼率帶來的對所有信源進行整體調整的缺陷，使控制系統在信元損失率最小情況下確保信源輸入流質量最高，從而有效地利用了網路帶寬。
  4. The hardware in this system includes a digital signal processor, an analogy input channel, a lcd, an analogy output path, a keyboard input part, a guard circuit and a logic control circuit

    該系統硬體包括數字信號處理器晶元、前向輸入通道、液晶顯示器、模擬量輸出部分、鍵盤輸入部分、保護電路部分和邏輯控制部分。
  5. In this dissertation, two kinds of optimization, methods are proposed. firstly, only these linking weights corresponding to the control rules that affect the control performance significantly are updated in order to reduce the compute works and speed up the training progress. secondly, the updating step is adjusted adaptively in accordance with the error and the change of error of the system based on the t - s model to get better performance

    針對模糊神經網路控制器一般存在著在線權值調整計算量大、訓練時間長、過度修正權值可能導致系統劇烈振蕩等缺點，提出了兩種模糊神經網路控制器的優化方法：在線自學習過程中僅對控制性能影響大的控制規則相關的權值進行修正，以減小計算量，加快訓練速度；基於t - s模糊模型，根據偏差及偏差變化率大小動態自適應調節權值修正步長，抑制控制器輸出的劇烈變化，避免系統發生劇烈振蕩。
  6. The second is data layer, including data acquisition and controlled quantity output

    第二層為數據層，包含數據的採集與控制量的輸出。
  7. This paper ' s software mainly includes data collection, data manager, interface design and output of control variables

    軟體設計主要包括數據採集、數據管理、界面設計和控制量輸出等。
  8. In automation control system, the actuator receives signals from controller or the manual operation, transfers them to the servomechanism ' s output. in that way, actuator adjusts the manipulated variable

    在自動控制系統中，執行器接收來自控制器的自動調節信號或手動操作信號，將其轉換成調節機構動作的輸出，從而改變控制量的大小。
  9. Firstly, apply protel99 software to design the sch chart of the high - speed intelligent control card and analog output card, secondly, design pcb charts and send them to the factory. 2

    首先應用protel99軟體設計高速智能控制卡和模擬量輸出介面卡的硬體原理圖，再設計印刷電路板圖並送廠制板； 2
  10. This control system adopts creditable plc for real control ; it sends many simulating signals collected by old sand temperature of inlet, suction opening temperature of double disk, inner sand temperature of double disk, current of mainframe and current of fan ; meanwhile, the operation signal and switching value signal outputted by material movement transducer is inputted to switching value module of plc ; it gets evidence of water feeding after cpu account ; the operation result of cpu is outputted by switching value of plc to control unlock combination of coarse, middle and thin water feeding electromagnetically operated valve and then gets different water feeding quantity

    該控制系統採用高可靠性的plc可編程序控制器進行實時控制，傳感器所採集的入口舊砂溫度雙盤抽風口溫度雙盤內砂溫主電機電流及鼓風機電流等模擬量信號直接輸入plc的模擬量採集模塊，同時加砂設備運轉信號及加砂設備物料移動檢測傳感器發出的開關量信號輸入plc的開關量模塊，由cpu獲取經運算而得到加水計算依據， cpu運算結果直接由plc的開關量輸出控制粗中細加水電磁閥的開啟組合，而得到不同的加水量。
  11. There is a lack of analysis apparatus of magnet, the new system is only a opened loop control system, if we add the analysis part of the ion eletrostatic accelerator someday, all that we need to do is adding analog module hi plc and sampling control arithmetic hi the computer program. we will get a perfect closed loop control system

    在目前缺乏磁分析儀的情況下，該系統雖然還只是開環控制系統，但是一旦加速器中束線分析部分到位，它只需增加模擬量輸出模塊和采樣控制演算法，就能形成完善的閉環控制系統。
  12. . pcl - 711b card offers many functions such as a / d conversion, d / a conversion, digital input and output and so on. in order to saving time, lightening the diffculty of programming, i take the programming method of driver level to control pcl - 711b card using visual basic6. 0 language

    Pcl ? 711b卡提供了a d轉換、 d a轉換、數字量輸入和數字量輸出等i o功能，為了縮短開發時間，減輕開發的難度，本文採用了visualbasic6 . 0對pcl ? 711b卡進行驅動程序級編程來控制該卡。
  13. With the computer controlling the output of the digital signals and the analog signals, controls and adjusts startup, stop, turn and rotational rapidity of the transducer - electromotor and the strength of brake actuator ; installs the torque sensor on dynamical axis, and installs the encoder on non - dynamical axis of the dimensional globoidal indexing cam mechanism ; utilizes the virtual instrument language labview development the test and control system, with the computer real - time monitoring, late displays and storages the data of the test, and processes the data and analyses it

    利用計算機控制數字量輸出和模擬量輸出來達到控制和調節變頻電機啟停、轉向、轉速;控制制動器的啟停和加載力;在弧面分度凸輪的加載軸和空軸上安裝扭矩傳感器和編碼器;應用虛擬儀器語言labview開發試驗臺的測控軟體系統，用計算機進行實時監測與事後顯示與存儲，並進行信號處理與分析。
  14. This dissertation defines two parameters based on the diversity measure as the input of the flc which is used to control the ga ' s crossover probability and mutation probability

    本文從群體多樣性的角度出發，定義了兩個參數作為模糊邏輯控制器的輸入變量，輸出為遺傳演算法的交叉概率和變異概率。
  15. In addition, the paper also designed the driving circuit for communication, the signal tuning and a / d convertion circuit for signal collection, and d / a convertion and the v / i transform circuit for output

    此外，本文還設計了用於通訊介面的隔離驅動電路、用於數據採集的信號調理電路和a / d轉換電路以及用於控制量輸出的d / a轉換電路和v / i變換電路等硬體電路。
  16. The engine controller is in fact a multi - dimensional, complicated non - linear mapping device of the inputs and outputs. therefore with the ability of mapping non - linear and complex functions, the multi - layer forward neural network can be used to establish these relationships based on the experimental data

    發動機控制器實際上就是一個多維的、復雜的傳感器輸入與控制量輸出的非線性映射裝置，因此，可以利用多層前向網路所具有的映射復雜非線性函數的性能，在大量數據的基礎上建立起該映射關系。
  17. Redundancy design and module circuit design have been used, and completely think over the adaptability to environment, self - protection and heat release. the control software is compiled with asm language, the software includes the air - fuel ratio control program under different situations, monitor program and signal processing program

    根據發動機的工作特性用匯編語言設計相應的綜合控制軟體，它包括發動機起動、怠速、加速、減速、恆速和變速變負荷等工況的空燃比控製程序、串列和并行通訊程序、信號採集及數據處理程序和控制量輸出程序。
  18. At the same time, this paper summarized the experience on solving the problem of amplitude limitation of the controller output and proposed a method to predict system output by use of the model prediction with feedback correction. the on - line intelligence switch of controller output between the limited amplitude and imc controller output is determined according to the state whether the system output and the predictive output are within the given error range

    同時，本文在總結前人對輸入受限問題的處理經驗的前提下，提出用帶反饋校正的模型預測作系統輸出預測，根據系統響應和系統預測值是否在給定誤差范圍內來共同決定控制量在限幅值與內模控制器輸出值之間進行在線智能切換。
  19. So can completely satisfy measurement request of various natural gas from all parts of oil and gas field and transmission pipeline in our country. there are switch function of multi - kind signal input, only need to simple setup by instruments menu, namely can realize lightly switching between multi - kind input signal, and has jumproved universality and reliability of instrument

    Do為無源開關量信號，操作器在手動控制時輸出開關量閉合信號給前級的dcs系統或調節器， dcs系統或調節器收到do狀態信號后即停止pid運算，並使操作信號輸出跟蹤閥位反饋信號。
  20. Tension control is a very important part of process control in many industrial applications, and plays an important role in improving product quality ^ enhancing system control security and etc. in this paper, electro - hydraulic proportional control methods are applied to control the export tension of the hydraulic motor and also the related winding machine by modulating the pressure difference between the inlet and outlet of the hydraulic motor, and the control methods are proven feasible

    張力控制是許多工業生產過程式控制制中的一個重要的組成環節。它對提高產品質量、增強系統控制安全等方面起著至關重要的作用。論文採用電液比例控制技術通過調節液壓馬達進出口壓差，控制其輸出扭矩，在完成卷繞機構收放過程中，對纜或織物的張力控制的方法是可行有效的。
分享友人
分享到 Line

分享到臉書