控制閥特性 的英文怎麼說

中文拼音 [kòngzhìfátèxìng]
控制閥特性 英文
valve characteristics
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 閥 : 名詞1 （指在某方面有支配勢力的人物或家族） established house or power group; a powerful person or...
  • 特 : Ⅰ形容詞（特殊; 超出一般） particular; special; exceptional; unusual Ⅱ副詞1 （特別） especially; v...
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  • 特性 : characteristic（s）; character; performance; features; properties; behaviour; response; character...
  1. Suction gas pressure goes up as the compressor run at the lower speed in the lower burthen, and this is beneficial to lower systems energy - consume. when the system is controlled by wvf, the discharge change of the evaporator is not linear ; the electronic expansion valve is adopted to regulate the system superheat degree, and the controlled object is parameter time varying, accordingly, the time varying controller should be adopted

    在負荷較小時，壓縮機採用低速運轉，吸氣壓力升高，這對系統降低能耗是有利的；變頻控制時，蒸發器製冷劑流量的變化並非線性；系統中採用電子膨脹閥進行過熱度控制，被控對象具有參數時變的特性，相應地宜採用變結構的控制器。
  2. By using the larger magnetic permeability, magnetic fluid was used to improve the magnetic circuit efficiency in torque motor, enlarge the output torque and displacement of torque motor, and the output flow of servo valve. correspondingly, the ability of noise - overcoming and system damping was enhanced due to the property of magnetic fluid. as a result, the stability of servo valve and servo - control system can be improved

    由於磁流體具有較大的導磁率，可提高力矩馬達磁路效率、增大力矩馬達的輸出力矩和位移，從而增加伺服閥的輸出流量;同時，利用磁流體的粘度特性，可增強力矩馬達阻尼及抗干擾能力，從而增強伺服閥及伺服控制系統的穩定性。
  3. The experiments include also two part, one is experiment of electromagnetic valve ' s flux character, the other is experiment of exhaust character

    通過測定電磁閥流量特性來控制二甲醚摻燒比例，通過測量柴油機的排放特性來確定二甲醚摻燒比例。
  4. Comparing and analyzing the synchronous control strategy, which brings up the new method to control the double un - symmetry jars proceed synchronously with the combination of proportional valve and servo valve, which forms closed loop control ; basing on the above methods, models are made to get mathematics models of position control system and to analyze system model theoretically by using pid controller, we can realize regulating parameters, minimizing synchronous errors and enhancing the dynamic performances ; the simulink tool box in matlab software is used to imitate the system according to the model, which not only makes the result visual and easy to adjust the parameters in interactive way but also lets us understand the effects of different parameters and optimizes the dynamic properties. the theory of plc control in dshp is discussed after advanced understanding of the system movements. hardware design and general regulation are given on the base of siemens company products s7 - 200 plc

    本文根據大量的國內外文獻，對研配液壓機的工作原理及設計結構進行了簡介；對位置同步的控制方法進行了比較分析，提出比例閥和伺服閥復合控制的閉環結構來對非對稱雙缸進行同步控制電液比例同步控制方案；在此基礎上著重對比例閥控非對稱缸建模，最後得到位置控制系統的總體數學模型，從理論上對同步系統動態特性進行了分析，並用pid控制器進行參數整定，減小雙缸同步誤差、提高系統的動態響應性能；其中控制性能的分析藉助于matlab軟體中的simulink工具箱，由已建立的數學模型形成模擬模型，得到可視化的模擬結果，從而利於交互方式下調整參數，了解不同的參數對系統的影響，優化同步系統的動態性能；在深入了解系統的動作特性后，對plc控制研配液壓機的原理進行了探討，針對siemens公司s7 ? 200型plc給出了硬體設計的總體規劃，編制出研配液壓機動作控製程序，在編程中著重研究位移傳感器與plc的通訊、雙缸同步運行的pid控制在plc上的實現及bcd碼撥盤輸入程序的植入問題。
  5. Abstract : the structure and the working principle of electronic - hydraulicvalve are analysed and the p - i ( pressure - control current ) characteristic equation of electronic - hydraulic valve is derived

    文摘:通過對電液閥結構與工作原理的分析，導出了電液閥的p ? i （壓力?控制電流）特性方程式。
  6. The meijiayi mjy channels therapeutic apparatus developed by our company, combines the advanced microcomputer technics with the profound traditional chinese medicine methods as well s the human channelss science, magically takes advantages of modern electronic technics and the outer treatment of chinese medicine, realistically simulated the effects like acupuncture, aprapathy, essage, eating, kin scraping and cupping, etc. which improve the comprehensive effects, especially for the common ailments and geriatric diseases in digest digestive system, respiratory system and nervous system

    旋翼式多流束濕式基表，雙脈沖采樣方式進行數據採集，採用計算機技術進行數據處理顯示控制閥門動作。它採用獨特的卡口安全及保護措施動態安全可靠的ic卡加密機制先進的硬體及軟體的容錯處理性能安全可靠，具有精度高自身功耗低體積小壽命長便於安裝等特點。能準確實現用水計量及實現預付費功能。
  7. Based on advanced technology, this thesis bring forward the optimal scheme and set down general system - drawings and flow charts. using step7 - micro software, we achieve the auto - control aim in drinking water treatment. in practice, the complexity and non - linaerity exit in the system of water treatment, so we apply fuzzy control in water treatment and design a kind of controller which structure can be altered according to the using - rate of ozone and the variety of water quality

    實際飲用水處理系統由於存在復雜性、非線性、時變性，本文根據臭氧生物活性炭水處理工藝存在復雜性、非線性、時變性等特點，將模糊控制應用在水處理這一不確定的非線性時變系統，針對不同水溫下臭氧利用率及水質的變化，設計一種基於系統過程狀態的變結構的模糊控制器，以單片機作為主要控制硬體，按查表方式設計軟體，對進水閥門開度進行在線控制，調節臭氧氣體與進水的比例（臭氧流量及濃度不變） ，達到氣水比最優化。
  8. This mode of valve is a kind of brand - new patent electromagnetic valve developed by this co., with an electromagnetic block as the auxiliary valve and not directly acting on the switch valve while only through adjusting the force difference between the media to get the switch valve, having lower energy consumption, longer duration, more stable performance etc. notable feratures, compared with the traditional electric valves, and extensively used for various water etc. liquids control system

    A型閥是我公司開發的一種新型專利電磁閥。電磁塊作為輔閥，不直接作用於開關閥，僅調節介質壓力差獲得開關閥，與傳統電動閥相比具有耗能低壽命長性能穩定等顯著特點。廣泛應用於各種控水油等流質的控制系統。
  9. Industrial - process control valves ; part 2 : flow capacity ; section four : inherent flow characteristics and rangeability

    工業過程式控制制閥.第2部分:流通能力.第4節:天然流動特性和量程范圍
  10. User can chang it freely. the signals sampled on hardware interrupt assure the real - time property and control reliability. chapter 4 first analyzes the basic characteristics of electropneumtic proportional / servo cushioning controlled system, especial study the influence of the valve dead zone, system friction and saturation phenomenon

    第四章首先將電-氣比例伺服控制引入到緩沖控制中，分析了系統被控對象的基本特性，著重分析了氣源壓力變化、閥口死區、系統摩擦力特性和氣路飽和現象對控制系統的影響。
  11. The nonlinear problem is ubiquitous and is difficult to solve in electro - hydraulic servo system. it is caused by the throttling property, because of the existing of the servo valve, proportion valve and throttling valve, by the dead band, the back lash and so on

    非線性是電液伺服系統中普遍存在且至今沒有很好解決的問題，這些非線性主要由電液轉換和控制元件（伺服閥、比例閥或節流閥）的節流特性和液壓動力機構的滯環及死區等因素引起。
  12. Using the precious metal resistant to compression characteristic, forms the precise linear delivery valve, besides may not have the section adjustment pressure value, also is in the present market condition adjusts one of scope biggest controllers, material quality use wrought aluminum alloy manufacture

    利用貴金屬抗壓特性，形成精確線性壓力閥，除了可以無段調整壓力值外，也是目前市面上調整范圍最大的控制器之一，材質使用鍛造鋁合金製造。
  13. Based on state space method of modern control theory, the mathematical model for the two way / two position hydraulic operated directional valve in thread cartridge is established

    摘要基於現代控制理論的狀態空間法，建立了螺紋插裝式液控換向閥開、閉過程的動態特性數學模型。
  14. Control valve characteristic depends on its flow rate, pressure drop, static pressure and valve stroke

    這些特性的明了與掌握，有助於控制閥的設計與操作問題的排除。
  15. The research indicated that, if the secondary combustion chamber was looked on as a controlled object, with the adjusting valve as a input, the pressure and the temperature of a selected point on the inside wall of the combustion chamber as outputs, then such controlled system would be a strongly non - linear, time varying system with number of random disturbances, which resulted in huge difficulty to build an analyzed mathematics model for the spray burning of the liquid fuel, so that classic control methods were all invalid

    研究表明，若將rbcc發動機的二次燃燒室視為一個控制對象，同時以燃燒室內壁面取定點處的壓強、溫度和調節閥的開度為輸入輸出變量，則該系統將是輸入?輸出特性非線性很強、隨機干擾嚴重的復雜時變系統。這導致建立燃油噴霧燃燒具體模型的很大困難，從而宣告了經典控制方案的失效。
  16. This thesis analyzes all kinds of throttle components, points out the advantage of adapting eev, and analyzes the start - up and the discharge characteristics of eev, and dynamic response of refrigeration systems when the opening degree of eev is changed, etc. eev is placed into a tumoff position while the unit starts up, and after being kept for a period of time it is placed into a bigger position, after some more time it is put into a basic control

    本文對比分析了冷藏箱製冷系統各種節流元件的特點，指出電子膨脹閥應用的優勢，同時分析了電子膨脹閥的啟動特性、流量特性以及系統在閥開度變化時的動態響應。電子膨脹閥在啟動時應先使電子膨脹閥處于關閉位置，延時一段時間后，再將閥開至一個較大的位置，再延時一段時間后轉移到基本的控制。
  17. In the light of significant energy losing during the hydraulic excavator working, a dynamic system was made up from the diesel engine, the variable pump, the control valve and the load to cut down the losing energy from a systematic approach based on the control characteristics of the system elements

    摘要針對液壓挖掘機在工作過程中存在的大量能量損失，根據泵的控制特性曲線，將發動機、變量泵、控制閥及負載作為一個動態系統來研究其節能問題。
  18. That is, through analysis of the principle on flow control and " hydraulic transistor ", design and calculation of flow control characteristic as well as main parts in valve inner chamber, a piloted reducing valve will be installed between main valve and pilot valve. after a pressure - difference compensating reducing valve was added in the non - pressure compensating piloted reducing valve of the flow control valve in vlalvistor valve, the calculation on control characteristic emulation and load characteristic emulation has been carried out. the result of the calculation shows that after pressure compensating reducing valve was added, the linearity of the control characteristics has been greatly improved thus eliminating influence upon outlet flow by load pressure - change of the hydraulic system and improving performance characteristics of the hydraulic component

    文章還在對瑞典valvistor閥的插裝比例閥研究的基礎上，提出了一種新的流量控制原理，即：通過對流量控制和「液壓晶體管」原理的分析、流量控制特性及閥內腔主要結構件的設計計算，在主閥和導閥之間增設先導減壓閥，並進一步對valvistor閥的流量控制閥之無壓力補償先導減壓閥、加入壓差補償減壓閥后的控制特性進行了模擬計算和負載特性模擬計算，結果表明：增設壓力補償先導增壓閥后，其控制特性曲線變得非常線性，從而消除了液壓系統負載壓力變化對主閥輸出流量的影響。
  19. As the demand for their high quality and good outline is increasing, the hydraulic control system of molding machine must be able to offer accurate pressure and flow control at the same time to its injection system

    集壓力、流量比例調節於一體的電液比例壓力流量復合控制閥（簡稱pq閥）以其復合程度高、控制性能好、節能等特點在注塑機液壓控制系統中得到了日益廣泛的應用。
  20. If by their ticket enforcement agencies use the power, control valves can be divided into pneumatic, electrical, fluid movement three, namely to compressed air to power sources pneumatic - valve to call for the engine electric control valves for the liquid medium ( such as oil ) pressure - driven electricity fluid moving control valves, and their functions and characteristics hours are electromagnetic valves, electronic style, smart, floor bus - control valves

    如果按其所配執行機構使用的動力，控制閥可以分為氣動、電動、液動三種，即以壓縮空氣為動力源的氣動調節閥，以電為動力源的電動控制閥，以液體介質（如油等）壓力為動力的電液動控制閥，另外，按其功能和特性分，還有電磁閥、電子式、智能式、現場總線型控制閥等。
分享友人
分享到 Line

分享到臉書