描邊路徑 的英文怎麼說

中文拼音 [miáobiānlùjìng]
描邊路徑 英文
strokepath
  • 描 : 動詞1. （照底樣畫） copy; depict; trace 2. （在原來顏色淡或需改正之處重復塗抹） retouch; touch up
  • 邊 : 邊Ⅰ名詞1 （幾何圖形上夾成角的直線或圍成多邊形的線段） side; section 2 （邊緣） edge; margin; oute...
  • 路 : 1 （道路） road; way; path 2 （路程） journey; distance 3 （途徑; 門路） way; means 4 （條理） se...
  • 徑 : Ⅰ名詞1 （狹窄的道路; 小路） footpath; path; track 2 （達到目的的方法） way; means 3 （直徑的簡稱...
  • 路徑 : 1. （道路） way; route; trajectory; path; tail; travel2. （門路） method; ways and means
  1. In computation of swept volume approximation, an improved technique to generate the swept volume approximation for arbitrary meshes is presented by introducing generator simplification and path resample using frenet moving frames along the discreted sweeping trajectory. other steps, such as a directed distance field computation on a uniform grid based on the hardware accelerated computation technique and iso - surface extraction using marching cubes algorithm, are also included in this algorithm. in addition, the simplification scheme and smoothing technique are applied to the swept volume generated from iso - surface extraction

    本文的主要貢獻在於：在掃描體逼近計算方面，在原有任意多邊形網格模型沿任意路徑運動生成掃描體逼近演算法的基礎上，提出了加入對掃描母體簡化的預處理和用活動標架對掃描路徑進行重采樣等過程，演算法的其它過程還包括：計算掃描體中幾何基元的排列，用硬體加速構造無符號的有向距離場，將無符號距離場轉化為有符號距離場，從有符號有向距離場提取等值面等。
  2. Not only the scan route solution, the built - in self - test solution and the boundary scan solution of design for testability are summarized, but also the applications and countermeasures of these 3 solutions are analysed and compared in details

    摘要綜述了超大規模集成電路的幾種主要的可測試性設計技術，如掃描路徑法、內建自測試法和邊界掃描法等，並分析比較了這幾種設計技術各自的特點及其應用方法和策略。
  3. ( 3 ) there are many flaws in direct laser metal sintering, such as the high remnants stress, micro - hole and micro - crack in sintering parts. in order to solving those problems, the programming of scanning paths is put forward, and several parts are prepared with different scanning paths respectively. the following conclusion is educed : the parts produced with short - side scanning path and same scanning direction have the minimum structure, the rigidity of parts prepared by short - side and same direction scanning path is highest, and the density of parts produced with the vertical scanning path is maximal

    （ 3 ）針對採用大功率激光直接燒結鎳基高溫合金成形金屬零件存在的問題，如較大的殘余應力，製件中存在著微裂紋、微孔洞等缺陷，初步提出掃描路徑的規劃，並採用幾種不同的掃描方式進行燒結試驗，發現採用短邊掃描路徑和同向掃描能夠獲得更加細小和分佈均勻的組織結構，採用短邊同向路徑制備的試樣其顯微硬度最高，而採用變向掃描（垂直）路徑制備的試樣緻密性最好。
分享友人
分享到 Line

分享到臉書