提升空氣流率 的英文怎麼說

中文拼音 [dīshēngkōngqìliúlǜ]
提升空氣流率 英文
lift air rate
  • 提 : 提動詞（垂手拿著） carry （in one's hand with the arm down）
  • 升 : Ⅰ動詞1 （由低往高移動） rise; hoist; go up; ascend 2 （等級提高） promote Ⅱ量詞1 （容量單位） lit...
  • 空 : 空Ⅰ形容詞（不包含什麼; 裏面沒有東西或沒有內容; 不切實際的） empty; hollow; void Ⅱ名詞1 （天空） s...
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 提升 : 1 （提高職級） promote; advance 2 （向高處運） hoist; elevate3 [數學] lifting; 提升器 lifting mec...
  • 空氣 : 1 （大氣） air; atmosphere 2 （氣氛） atmosphere 3 （氣閘） air brake4 pneum ; pneumo ; pneumat ;...
  1. Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high

    通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。
  2. Later, the paper ascertains how the prominent factors influence the humidifying effect by single factor experiment and got such solutions : when other situations do n ' t change, the nozzle flux will enhance with the increase of the nozzle aperture and spraying pressure. air ' s changing quantity of enthalpy and absolute humid, valid humidified quantity, humidifying efficiency and saturation efficiency will enhance with the increase of the initial water temperature. with the enhance of the praying pressure, the valid humidified quantity and air ' s changing quantity of enthalpy will increase first and decrease later, while the humidifying efficiency will drop

    然後通過單因素試驗確定影響顯著的因素如何作用加濕效果，得到：在其他條件不變的情況下，噴嘴流量隨噴嘴孔徑和噴水壓力的升高而增大，空氣焓變量、絕對濕度差、有效加濕量、加濕效率及飽和效率隨噴水初溫的升高而提高，有效加濕量和空氣焓變量隨噴水壓力的升高先增加然後有所下降，而加濕效率隨噴水壓力的升高而下降，焓變量和絕對濕度差隨水氣比的增加而增大。
  3. While the speed is very large, the fuel - air mixing behind the airstream is decreased and the span that the fuel flow in the second combustor is reduced, so the combustion efficiency is decreased, h ) if the fuel streams impinge with the airstreams directly at the air - inlet exit, it make against increasing the combustion efficiency, i ) increasing air - to - fuel ratio within proper range can increase the combustion efficiency

    增加燃氣噴射速度有利於增強迴流區強度，頭部燃燒溫度上升，但速度太大則會減弱燃氣同空氣在進氣道下游的摻混燃燒，減少燃氣在室內停留時間，燃燒效率降低； 8燃氣射流與空氣流在進氣道出口直接撞擊不利於燃燒效率的提高； 9在適當范圍內增大空燃比能顯著提高燃燒效率。
  4. With computations and analysis, the comprehension on the mixing and combustion process is increased, and some significative results are listed below : a ) there are three recirculation regions and one vortex region in the combustor, and these recirculation regions affect the combustion process deeply, b ) increasing side - arm angle and moving side - air inlet position toward the fuel inlet can improve mixing and combustion characteristics, and increase the combustion efficiency, c ) when the angle between two air - inlets equals to 180

    通過計算與分析，增進了對補燃室內摻混燃燒過程的理解，為固體火箭沖壓發動機補燃室設計提供了一些有意義的結果： 1補燃室內的流動十分復雜，存在三個迴流區和一個旋渦區，迴流區對摻混燃燒過程有重要影響； 2增大空氣入射角度、向前移動進氣道出口位置有利於增強頭部迴流區強度，增強摻混效果，燃燒效率上升； 3
分享友人
分享到 Line

分享到臉書