搭接的 的英文怎麼說
中文拼音 [jiēde]
搭接的
英文
lapped-
The most commonly used joint configurations are the lap, scarf, and butt joints.
最常用的連接結構是搭接,嵌接和平接。Adopt zero velocity full auto paper receiving mode, end to end butt paper receiving, auto double side stickup connection adhesive tape so as to avoid spoilage of die cutter and dinkey dint of overlapping paper registration
採用零速全自動接紙方式,頭對頭對接接紙,自動雙面粘貼連接膠帶,可避免搭接接紙對印版的壓傷及對模切刀具的損壞問題。Standard specification for lap cement used with asphalt roll roofing, non fibered, asbestos fibered, and non asbestos fibered
用於無纖維增強石棉纖維增強和無石棉的纖維增強瀝青屋頂卷材的搭接膠粘劑標準規范Belt - making apparatus adopts supersonic wave welding machine, the tail of parcel hasp with iron sheet sleeve pipe is fixed with puncher, make its hasp intensity up to more than 6, 500 newton
制帶設備採用超聲波焊接機,鐵皮套管包裹搭扣的尾部,用沖床加以固定,使其搭扣強度達到6 . 5千牛以上。Control equipments of resistance welding machines for lap joint
搭接用電阻焊接機的控制設備Destructive tests on welds in metallic materials - tensile test on cruciform and lapped joints
金屬材料焊接的破壞試驗.十字形接縫和搭接縫的抗拉試驗Testing of adhesives for metals and adhesively bonded metal joints ; creep test on single lap joints
金屬和粘結的金屬接點用的粘合劑的試驗.單搭接粘膠點Adhesives - wood adhesives for non - structural applications - determination of tensile shear strength of lap joints
膠粘劑.非結構用木材粘結劑.搭接接頭拉力剪切強度的測量Mcx radio - frequency connectors. part 36 : sectional specification for microminiature r. f. coaxial connectors with snap - on coupling. characteristic impedance 50 ohms type mcx
射頻連接器.第36部分:搭鎖式耦接的微型射頻同軸分規范.特性阻抗50歐姆With the amount of ch3sicl2 increased, however, the linear molecule and orbicular organic compounds containing si, o and n element were formed, which resulted decrease of gasification velocity of precursor and purity of si - c - n nano - powders
而fis樸。柱狀晶在長大過程中與相鄰的ps柞。柱狀晶相互靠近、搭接,限制了玻璃相的滑移,提高了復合材料的高溫強度。This paper have studied some questions which included distributed load, lapped length, becoming less crowded purlins each other in the lap joints, mechanic analysis, lateral buckling and ultimate load - carrying capacity and construction of double purlin in the lap joins. according to result of test and analysis of theories, the author advances the suggestions, which may be a reference to steel structure design
文章對z型連續搭接檁條荷載分佈、搭接長度、搭接嵌套松動、側向穩定以及構件極限承載力和雙檁條的構造等問題進行了研究,並根據試驗結果和理論分析提出了建議。The subsea wellhead production system, named building block subsea system, adopts the most advanced technologies in the world, including the subsea horizontal christmas tree, electro - hydraulic control system, mudline booster pump, umbilical assembly, host, and rov, etc
被稱為「組塊搭接式控制系統」的水下井口生產系統,薈萃了當今世界的尖端技術,包括雙定位水下臥式採油樹、電/液控制系統、泥線增壓泵、電纜系統、折疊式鉆井底盤系統和遙控作業機器人等。Although the join - structure increases the redundancy ability and enhances the security when maglev train runs at high speed, the two suspension points on the same join - structure coupled closely
搭接結構增加了列車懸浮系統的冗餘能力,提高了列車在高速行駛時的安全性。When the join - structure is suspended, suspension state message between the two suspension points should be exchanged and the digital suspension controller will communicate with the sensor. this function is realized by rs - 485 serial communication
在對搭接結構進行懸浮控制時,兩個懸浮點之間需要實時交換狀態信息,並且傳感器與數字懸浮控制器之間也要傳輸數據,兩類信息交換是通過rs - 485串列通信來實現的。The experiment result shows that the control method designed in the dissertation can ensure the steady suspension of the join - structure. when there is something wrong with one suspension point on a join - structure, the variation of suspension clearance of the other is only about 0. 8mm. it manifests that this method can achieve the join - structure ’ s redundancy function
本文最後在原理型搭接裝置上進行了懸浮控制實驗,實驗結果表明:文中所設計的控制方法能夠實現原理型搭接裝置的穩定懸浮,而且搭接裝置上的一個點出現故障時,另一個點的懸浮間隙最大增加量僅為0 . 8mm左右,由此說明該方法能夠確保搭接結構冗餘功能的實現。It is difficult to ensure the steady suspension of the join - structure if the control method of the two suspension points is designed independently, so the coupling force between the two points must be taken into account. in this dissertation, the model of the join - structure is built. the model is decoupled and linearized by differential geometry method
但是,同一搭接結構上的兩個懸浮點之間具有很強的耦合作用,在對搭接結構進行懸浮控制時,如果對兩個懸浮點獨立進行懸浮控制設計,很難使搭接結構穩定懸浮,因此必須考慮它們之間的耦合作用。So as to deal with this problem, local b - spline surface designing method with complicated trimmed boundary constraints is advanced. for two neighboring surfaces, we first trim a belt along the common boundary and then bridge a b - spline surface between these two trimmed surfaces with a smooth blending. with respect to the comer area comprised of several adjoining surfaces, a rectangular region covering the comer area is obtained by trimming operations at first, and later a local b - spline for filling the rectangular region is completed through interpolation or approximation
在兩張相鄰的曲面之間,先在其公共邊界處裁剪出一個帶狀區域,然後再採用曲面搭接的方式實現曲面之間的光滑過渡;而在鄰接曲面的公共角點處,先在該角點附近區域裁剪出一個矩形拓撲域,然後運用插值或逼近的方法,設計出一張既滿足於該區域的邊界條件同時又插值或逼近內部采樣點的b樣條曲面。However, the brace member of k - joint may meet at the chord member partially in the many structures
然而,在實際工程中的k型節點經常會遇到支管在與主管交匯處部分搭接的情況。Overhangs the body and so overlaps onto an adjacent piece
在印刷技術中,一個鉛字由其身向外突出與相鄰的鉛字相搭接的部分。The switch is made from two thin, flat strips of ferromagnetic material called reeds, with contacts on the overlapping ends
開關是由兩個扁平的磁性材料薄片組成的,這兩個薄片被稱為簧片,觸點位於簧片上相互搭接的一端。分享友人