撓度法 的英文怎麼說

中文拼音 [náodùfǎ]
撓度法 英文
deflection method
  • 撓 : 動詞1. （輕輕地抓） scratch 2. （擾亂;阻止） hinder 3. （彎曲,比喻屈服）yield;flinch:不屈不撓indomitable; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  1. Third, on the base of expatiating on experimental research method and theoretical research method of joints, the paper points out two kinds of valid methods, which are used to analyze the tube joints stress of dendriform structure by making use of semi - analytical method and inelastic large deflection finite element analysis method, confirms to apply the evaporative pattern casting process as the facture method of dendriform structure cast joints, and detailed dissertates the casting theory, casting process, generation cause and prevention measure of casting flaws, heat treatment method and inspection standard about cast steel joints

    然後在闡述樹狀結構節點實驗研究方法和理論研究方法的基礎上，提出了利用半解析法和彈塑性大撓度有限元法兩種有效分析樹狀結構管節點應力的方法，並給出兩種方法的詳細表達式及它們各自的優缺點。通過對鑄鋼件常見製作方法的介紹，確定了採用消失模法作為樹狀結構鑄鋼節點的製作方法，並詳細論述了用消失模法製作鑄鋼節點的鑄造原理、鑄造工藝、鑄造缺陷產生的原因及防治措施、鑄鋼節點的熱處理方法以及檢驗標準。
  2. Presents a new method for fairing of curves which has a small flexibility based on fitting the derivative of second order of curves. we fit the derivative of second order of curves by a polynomial fitting, then find an indefinite integral of this polynomial to get a approach of curves. otherwise, we discuss the analyze of the error and the optimize of fairing to this arithmetic

    提出了一種針對小撓度曲線的逆向曲線光順演算法，該演算法直接擬合曲線型值點列的二階導數曲線，然後通過兩次積分來反求出光順后的曲線，並對該演算法的誤差分析、效果分析、光順優化等問題進行了深入探討。
  3. Also, the thesis calculate and analysis the transverse deflection of steel box girder deeply in multiple factors. firstly, the article introduced the calculative methods and theory of local stress and strain of bridge structure. then program software system of finite element method was introduced. after that, the influential factors to the calculatial result and their values were analysed and suggested

    本文首先介紹了橋梁結構局部應力應變計算理論和方法，對有限元計算程序進行了介紹，然後分析了縱橫隔板設置、梁高及梁寬變化等因素對鋼箱梁橋面板在恆載作用下的橫向撓度的影響，並將這些計算結果進行對照分析，從而找出了影響橋面板橫向撓度的主要影響因素，並得出了相應的數值可供工程實踐參考。
  4. The research shows that : 1 ) the ductility of the hsc bending members constructed is much greater than 5 ; 2 ) increasing the vertical links and distribution steel can increase the deflection under ultimate moment ; 3 ) with appropriate compressive bars, vertical links and distribution steel the increase of moment after yield and the decrease of moment under ultimate moment can be ignored, so the ductility of the hsc bending member is much larger ; 3 ) the width / depth ratio of hsc bending member has no obvious effect on the ultimate compressive strain of concrete ; 4 ) the method used here to calculate the deflection is applicable ; 5 ) the location of crack coincides with the location of vertical links and distribution steel ; 6 ) the bending property of the hsc structure under the blast load can meet the demand of protective engineering

    研究表明：本文研究的梁、板構件的延性比遠大於5 ；增加箍筋（鉤筋、分佈筋）含量，可以提高壓區混凝土剝落時的撓度；在適當的受壓筋、箍筋（鉤筋、分佈筋）含量下，可以忽略壓區混凝土剝落瞬間的承載力下降，從而大大提高構件的延性；受彎構件的寬高比對壓區混凝土極限應變的影響不明顯；受彎構件的裂縫間距受箍筋（鉤筋、分佈筋）的布置影響；文中所用的承載力和變形計算方法是可行的。化爆試驗表明，高強混凝土構件的動載抗彎性能能夠滿足防護結構的要求。
  5. Along with the progress of drilling technology, many new types of bha such as steering motor assembly, dropping assembly with eccentric bend sub, dropping assembly with flexible connection are developed based on common building, dropping and holding assemblies. for using these bha, a new mathematical model is put forward for 3d static analysis of these types of bha under small deflection. and its weighted residual solution is given. the mathematical model includes ( 1 ) differential equations ; ( 2 ) boundary conditions at drill bit, stabilizer, bend angle, diameter change, tangential point and borehole wall ; ( 3 ) lateral forces and deflection angles of bit. the software based upon this method runs well

    為了更好地應用各種新鉆具，建立了適用於對普通下部鉆具、導向鉆具、帶偏心彎接頭和柔性接頭的下部鉆具進行三維小撓度靜力學分析的數學模型，包括（ 1 ）微分方程； （ 2 ）鉆頭、穩定器、彎角、變截面、切點和井壁的邊界條件； （ 3 ）鉆頭的側向力和鉆頭轉角.給出了該模型的加權余量解.用該方法編寫的軟體應用效果良好
  6. In the hogging condition, double bottom and the side shell remain the ultimate bucking strength, deck and upperwing tank remain the yield stress, and the other parts keep elasticity. then the key to calculate the ultimate strength of ship hull girders is to ascertain the ultimate bucking strength of the stiffened panels. in this regard, the developed formulation is designed to be more sophisticated than previous simplified theoretical method for calculating the ultimate strength of stiffened panels under combined in - plane bending and lateral pressure. fabricatio n - related initial imperfections ( initial deflections and residual stresses ) are included in the panel ultimate strength calculation as parameters of influence. all possible collapse modes involed in collapse of stiffened panels, including overall buckling collapse, column or beam - column type collapse, tripping of stiffeners and local bukling of stiffened web are considered

    確定了船體梁整體破壞時的剖面應力分佈之後，關鍵在於確定板架的極限屈曲強度。本文充分考慮了在縱向彎曲、橫向壓力作用下加筋板可能發生的幾種破壞模式，即板架的整體屈曲破壞、樑柱形式的破壞、筋的側傾、腹板的屈曲並同時考慮了初始焊接殘余應力、初撓度的影響，使其更精確的計算加筋板的屈曲強度。對于加筋板中加強筋腹板的局部屈曲，採用解析法推導出筋的腹板的撓度方程及其邊界條件，求解相應的方程，從而計算出腹板的局部屈曲應力。
  7. We may use the plane stress analysis for determining deflections in the midplane of the beam.

    我們可以用平面壓力的分析方法來確立梁中間面的撓度。
  8. Study of deflection measure method on bridge load test

    橋梁荷載試驗撓度測試法研究
  9. This article discuss the method to measure distortion of truss by means of ccd device. the distortion can be measured with many kind of displacement transducer, but it must be placed on stable base. when the huge truss is moving through some tunnel, it is difficult to find a stable base, especially there is no enough space for someone to operate. it is hardly to measure the distortion by touching. on the contrary, this can be achieved by means of ccd device

    桁架在自重或載荷的作用下產生的撓度可以用多種位移傳感器測得，這些測量方法需要有良好的基礎，在大型桁架梁測量現場，由於桁架的變形，難于找到這種基準，如果加上測量環境惡劣，人無法操作情況，則會給撓度測量帶來極大的困難，而採用光電荷耦合器件，並利用激光進行遠程實時撓度測量，即可以解決這個難題。
  10. The proposed model is compared with experimental beams in the midspan cross - section deflections, strain distribution and the slip of supporting points

    為驗證有限單元法的正確性，對試驗梁進行了跨中撓度、沿梁高應變分佈及梁端滑移的計算分析。
  11. Dq method for the deflection of thin rectangular plates

    矩形薄板線性彎曲撓度的微分求積法研究
  12. We research on the thermal buckling characteristics of double layer membrane which is composed of different materials with different thermal expansion coefficiens under uniform temperature elevation. the energy method is proposed which is used to solve the problem and the symbolic relation between central buckling height and substrate height under small buckling height is also given. it is the primary theory of membrane resonant sensor, which makes the research and development of novel thermal sensor possible

    本文對微機械中熱脹系數不同的材料構成的雙層復合薄板在均勻溫升下的撓曲特性進行了研究，提出了在均勻溫升下雙層薄板熱撓曲求解的能量法，並給出了小撓度下中心撓度與板厚的解析關系，為薄膜諧振式傳感器溫度特性的研究和新型溫度傳感器的設計與開發打下了基礎
  13. On basis of ship strength theory, mathematical model and solvable method of limited deflections of ships are established, and deflection criterion to check the demands of longitudinal strength of intact ships or damaged ships is proposed. it is convenient for the preliminary ship design

    根據船體梁強度理論，建立船舶極限撓度數學模型與求解方法，提出利用船舶撓度檢驗船體總縱強度的新方法，可以較方便地對正常或破損船舶總縱剩餘強度進行檢驗，便於初步設計。
  14. Weighted solution of small - deflection bucklingequation of thin shell

    薄殼小撓度屈曲方程的加權解法
  15. Method for measurement of static deflection of power presses

    機動壓力機的靜載撓度的測量方法
  16. By this method of analysis, researcher can get all of elastic characters without choosing proper perturbation parameter to create perturbation solution. since this method of analysis reduce the experience factors in the process of analysis, the results of it can be more reasonable

    採用該方法求解板以及殼體的大撓度問題，研究者無須具體選擇攝動解的攝動參數就能夠得出問題的全部彈性特徵，減少了在攝動過程中的先驗因素，使得求解結果更趨于合理。
  17. The optimized reservoir ope ration is simulated for baozhusi hydropower station in sichuan. the analysis resu lts prove the rationality, feasibility and practicality of the model

    採用解析法對主梁進行了撓度計算，與試驗數據進行比較並分析了計算結果，認為橋機主梁的主梁強度、剛度實時檢測、監控系統基本上是可靠的，主梁2基本沒有塑性變形。
  18. In the analysis of the elastic local buckling strength of the stiffener ' s web, the elastic critical stress is analytically derived by solving the characteristic value problem involving the governing differential equation under the corresponding loading and boundary conditions

    對于加筋板中加強筋腹板的局部屈曲，則用解析法推導出筋的腹板的撓度方程及其邊界條件，求解相應的方程，從而計算出腹板的局部屈曲應力。
  19. Chapter two discourses the basic theory, calculation model and main advantages and disadvantages of regression analysis and time series analysis. chapter three discusses grey system theory in detail, including the basic theory, grey incidence analysis, model in common use and forecasting method. chapter four analyzes the results of flexibility deformation of 270 meters span continuous rigid frame bridge of humen bridge, calculated with regression, time series and grey system model

    第1章介紹了變形監測的目的、意義、分類以及變形分析與預測研究的現狀和進展；第2章論述了回歸分析和時間序列分析的基本理論、計算模型和主要優缺點：第3章詳細討論了灰色系統理論，包括建模的理論基礎、灰色關聯分析、常用模型和預測方法；第4章為採用回歸模型、時間序列模型、灰色系統理論模型，對虎門大橋270米混凝土連續剛構橋施工中的撓度變形進行的計算分析。
  20. In the procedure, the column is first divided into a finite number of small segments in equal length. the deflection - curvature relation of each segment is determined using the finite - difference method. the final nonlinear algebraic equations are then obtained by means of the equilibrium condition for each segment

    運用這種方法，先將長柱離散成若干等長的柱段，利用差分方法求得各柱段截面上的撓度與曲率的關系，再根據各截面上外力與抵抗力的平衡條件，得到一組關于荷載與變形關系的非線性代數方程組；本文對該方程組採用載荷增量法進行迭代求解。
分享友人
分享到 Line

分享到臉書