撓曲變形 的英文怎麼說

中文拼音 [náoqūbiànxíng]
撓曲變形 英文
bending deformation
  • 撓 : 動詞1. （輕輕地抓） scratch 2. （擾亂;阻止） hinder 3. （彎曲,比喻屈服）yield;flinch:不屈不撓indomitable; unyielding
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  1. Zijingguan fault zone is characterized with cataclasite series of tectonic rocks and joints alongside the deformational zone, and sometimes with uniclinal flexure or folds. the intensity of deformation increases from the sides to the center of the fault in the section, which appears from joints to cataclastic rocks

    紫荊關斷裂帶兩主斷裂變形帶以碎裂巖系列構造巖和節理帶組合為特徵，局部出現撓曲和褶皺，由兩盤至斷裂中心變形強度增大，一般由節理帶過渡為碎裂巖帶。
  2. And results are : ( 1 ) analyze the force and distortion on pipeline under collapse and gulch in theory. on the base of beam deformation, analyze the bending moment and deformation of pipeline with frusta and without frusta. calculate a true problem, contrast the differences between pipeline with frusta and one without frusta, draw some conclusions

    得到的主要結果為： （ 1 ）基於彈性地基理論和彈性梁的撓曲線理論，給出了管道在固定墩（相當跨越河溝情況）和無固定墩（相當坍塌和沖溝情況）的變形微分方程，並分析了當量軸力為拉力或壓力時管道的變形和受力情況。
  3. As an application of this fem preprocessing system, the simulation on the welding process of missile ’ s oil box was performed, in which the effects of the welding sequences of four web plates and welds on each web plate are primarily analyzed. the simulation results show that the deformations under varied welding sequences are almost the same. downward deflection deformation is obtained along the weld longitudinal direction in the structure as well as upward deflection deformation along the weld traverse direction

    對于某型號導彈油箱結構焊接過程的數值模擬計算，主要考察了每塊立板上各段焊縫焊接順序的調整、四塊立板之間不同的焊接順序以及焊接起始端的選擇對結構焊后變形的影響規律，模擬結果表明:壁板在各種焊接順序下的整體變形規律基本相似，即焊後壁板沿焊縫縱向發生了向下的撓曲變形，中部向下變形量最大;沿焊縫橫向發生了向上的撓曲變形，壁板兩端部變形量較大，且壁板前端變形大於壁板後端。
  4. The meso - cenozoic evolution of bachu fault - uplift is closely related to its south and north subsiding foredeep. under the background of indian plate subducting under asia - europe plate, bachu forebulge was greatly affected by the development of southwest depression and awati depression. almost all of its structure reversed, and as a result of it, both of its south and north boundary migrated. according to its evolution history and its feature, the authors tentatively use both - side migration model to interpret the evolution of compound forebulge. since triassic, almost all the spheres above lithosphere synchronously became flexure. because transpressional stress field became increasingly strong, bachu forebulge continued uplifting and big faults formed. then, bachu uplift, as a whole, slipped upward along those big faults and showed migrating toward thrust zone in plane. in tectonic tranquility, the lithosphere bounded back and in consequence of it, bachu uplift slipped down and showed migration toward craton, at that moment negative inversion structures developed. while the forebulge migrated toward its south and north foredeep, it was very possible that locally extensional stress appeared in the forebulge

    在印度板塊向歐亞板塊俯沖的大背景下，巴楚前緣斷隆受西南坳陷和阿瓦提凹陷的影響，新生代時構造體制發生反轉，邊界向南北遷移。根據其發育過程特徵，作者用復合前緣隆起兩端遷移模式對復合前緣隆起獨特的構造發育史進行了解釋：即三疊紀以來巖石圈各圈層同步撓曲變形。隨著擠壓應力場的增大，巴楚隆起在撓曲基礎上不斷抬升，形成幾條大型斷裂帶。
  5. Partially prestressed concrete structure has been widely used in the field of civil engineering. the deformation is very important for prestressed concrete members, for they are thinner than those of reinforced concret owe to the adoption of hign - intension material and developed technic of design and construction. at present, there are some formulae for deformation in the criterion of many countries. mostly there are 3 methods in use : double linearity method, method of valid inertia and curvature integral calculus method. this article will discuss the influence of material, spa, construction form, and adjust the formula for stiffness of gb50010 - 2002 to a new uniform formula for deformation

    在土木工程領域，部分預應力混凝土結構因其良好的跨越能力和經濟性而得到了廣泛的應用，並發揮了巨大的作用。由於採用了高強度材料並進一步改善了設計和施工技術，預應力混凝土構件一般比普通鋼筋混凝土構件更為細巧，因此，撓曲變形問題顯得尤為重要起來。目前，各國規范對于部分預應力混凝土構件的變形計算均有相應的公式，變形計算的關鍵是剛度的計算。
  6. As regards to the spheric thin shell structure under external hydro static pressure, basing on flat - plate theory and by using basic von karman equations for large deflection, the equilibrium problem of axisymmetric bending of the spheric shell under uniform external pressure is simplified to an equilibrium problem of bending of elastic basic flat - plate and further converted into an equilibrium problem of beam on elastic fundation taking into consideration of the deformation characteristics

    對球形薄殼結構隨靜水外壓的情況，應用平板理論中的vonkarman大撓度基本方程，將球形薄殼在均勻外壓下的軸對稱彎曲平衡問題簡化為彈性基礎平板的彎曲平衡問題，進而再根據變形特點將其轉化為彈性基礎梁的復雜彎曲平衡問題。
  7. Advanced technical ceramics. methods of testing monolithic ceramics. thermo - mechanical properties. determination of flexural creep deformation at elevated temperatures

    高技術陶瓷.整體陶瓷的試驗方法.熱機械特性.在升溫條件下測定撓曲蠕變變形
  8. The mathematic model of the ultra - thin spherical mirror is to be treated as elastic thin shell. then the predigested model, i. e., bended beam, used in qualitative analysis was proposed, and its deflection and stress formulas under the freely supported condition were set up. based on an off - axis aspherical primary mirror, the relationship of aspherical surface error ( rms ) in tangential plane with bended beam ’ s radius r, position s of concentrated load p and geometry length l of arc was analyzed

    根據這一設想，本文建立了超薄鏡的數學模型?薄殼，並提出了強制力作用下超薄鏡的簡化模型?曲梁，推導了曲梁在簡支情況下受力變形的撓度公式，並結合一個實例，計算出曲梁變形后與所需非球面的面形殘差（ rms ）在子午方向與曲梁弧長l 、曲梁半徑r及集中力位置s的關系及滿足面形精度的r和s范圍，分析了弧矢方向的rms ，得出了同時滿足子午和弧矢方向面形要求的l 、 r和p 。
  9. In the procedure, the column is first divided into a finite number of small segments in equal length. the deflection - curvature relation of each segment is determined using the finite - difference method. the final nonlinear algebraic equations are then obtained by means of the equilibrium condition for each segment

    運用這種方法，先將長柱離散成若干等長的柱段，利用差分方法求得各柱段截面上的撓度與曲率的關系，再根據各截面上外力與抵抗力的平衡條件，得到一組關于荷載與變形關系的非線性代數方程組；本文對該方程組採用載荷增量法進行迭代求解。
  10. The main purpose of this paper is to realize the section properties and moment capacities of profiled sheets by experimental study and academic analysis for three types of profiled metal sheets which are called u450, u860and super combination profiled metal sheets produced by shanghai baosteel metallurgical construction corporation. its main contents include : ( l ) according to " european recommendations for the testing of profiled metal sheets ", the moment capacities of 32 full - size u450 and u860simple and continuous specimens are tested. ( 2 ) using the finite element program ansys and nonlinear finite element method, the moment capacities of super combination profiled metal sheets profiled are analyzed

    主要內容有： （ 1 ）依據《金屬壓型鋼板試驗歐洲建議》 ，進行了32塊1 : 1的u450 、 u860二類壓型鋼板試件簡支、連續板彎曲性能試驗研究； （ 2 ）採用有限元程序ansys對超級組合壓型鋼板受彎性能進行了非線性有限元分析，分析中考慮了大變形與幾何初缺陷，得出其荷載?撓度曲線與極限荷載p _ （ max ） ，通過截面特性與曲線斜率、極限荷載的關系式得到截面特性；並將分析結果與同濟大學試驗結果進行對比分析。
  11. On the basis of relative researches in the world, according to the study status of steel - concrete composite slab, which would be widely used in modern bridge, modified equivalent inflexibility of steel - concrete composite slab was deduced by use of conversion section principle in this paper ; based in this, this paper put forwards the theory of ultimate flexural capacity of steel - concrete composite slab in consideration of slip effect, and introduces the practical simplified method for calculating flexural deformation of steel - concrete composite slab in consideration of the effect of steel studs and welded wire, and conclude that the methods in this paper is veracious and reliable, comparing with the traditional calculating mode ; morever, this paper put forwards the calculating theory and program of the effect analysis of creep and shrinkage to steel - concrete composite slab, using conversion elastic modulus principle, and testifies that the theory is right and the program is reliable and practical

    本文在國內外研究成果的基礎上，針對壓型鋼板與混凝土組合板結構在現代橋梁建設中廣泛應用前景和研究現狀，利用換算截面法導出了壓型鋼板與混凝土組合板結構的修正等效慣性矩；在此基礎上，又推出了考慮壓型鋼板與混凝土之間的相對粘結滑移影響的壓型鋼板與混凝土組合板結構極限抗彎承載能力計算理論，並介紹了考慮栓釘、聯結件影響的壓型鋼板與混凝土組合板結構簡化實用撓曲變形計算公式，而且通過與傳統計算理論的分析比較，表明本文提出的計算理論公式的準確可靠性；此外，採用換算彈性模量比法著重提出了壓型鋼板與混凝土組合板結構的徐變、收縮效應分析的計算理論和程序，並通過實例分析計算證明了理論的正確性、程序的可靠性和實用性。
  12. Nonlinear constitutive relations are discussed for analyzing the stress distribution, the appearance and development of the cracks, as well as the behavior of the boundary conditions of the two way slabs respectively. in the light of the experimental research on r. c. two way slabs under static loading, the behavior of yield line, the load deformation curves and the crack yield, plastic limit loads of slabs with different supporting conditions are studied

    根據反映雙向板混凝土材料非勻質性的本構關系，分析了雙向板在荷載作用下的變形、屈服、裂縫和破壞的形態特性，並對鋼筋混凝土雙向板在不同支承條件下的塑性極限荷載、正常使用撓度（曲線）和截面設計作了進一步研究。
  13. The calculation of flexural deformation of cold - formed steel - deck concrete floors

    混凝土組合樓板撓曲變形計算
  14. According to the transferring matrix method, the paper presents a method for calculating the deflection of a filament wound tapered tube at bending and the calculation result is proved by experiment results

    本文以傳遞矩陣法為基礎，計算纖維纏繞錐管在彎曲載荷作用下的撓曲變形，並以實驗結果驗證了計算結果。
  15. In this thesis, it is analyzed theoretically the steel bar layout pattern, the prestress loss, the concrete stress, and the discipline of the deformation and the fracture forming of structures of the partial prestress concrete frame beams, which is widely used in modern civil engineering

    本文從理論上分析了現代建築工程中廣為採用的部分預應力混凝土框架梁的布筋方式、預應力損失、混凝土應力、結構變形和開裂規律；導出了具有一般意義的預應力錨固損失以及梁的長期撓曲變形計算公式。
  16. For each curvature incremental step, a deformed curve in the correspondi ng state can be determined for the column. through the iteration for all incremental steps until the solution is convergent, the complete load - deformation relation can then be obtained

    對各曲率增量進行反復迭代，直至得到收斂解，就獲得了長柱從加載到破壞的全過程變形曲線及荷載-撓度曲線。
  17. First, higher - order shear deformation theory and reddy ' s simplified higher - order shear deformation theory of the flat shell is adopted to obtain the buckling governing equations. then the geometric nonlinear theory and the geometric and material dual - nonlinear theory with shear effects are introduced ( the buckling governing equations are get ). the simplified geometric nonlinear theory and the small defection theory are discussed as emphases

    首先採用扁殼高階理論及reddy型簡化高階剪切變形扁殼理論，得到了屈曲基本方程，然後介紹了考慮剪切的幾何非線性理論及材料幾何雙重非線性理論（得到了屈曲基本方程） ，重點討論了簡化的幾何非線性理論及小撓度理論。
  18. Observing the mechanics and effect of the new strengthening method with test and finite element method is supposed to offer a guide for technology and become valuable in theory and practice. both compression test, including four reinforced and three control specimens, and shear - compression test, including nineteen reinforced and four control specimens are being studied in this paper. the research on the curves of load - strain, load - deflection and hysteretic shows that the transverse translation of the reinforced columns is well controlled with an upgrading of both ductility and ultimate bearing capacity ( ubc )

    本文對4根鋼絲網外噴高強砂漿加固鋼筋混凝土柱和3根對比鋼筋混凝土柱進行了軸壓試驗研究，並對19根加固鋼筋混凝土柱和4根對比鋼筋混凝土柱進行了剪壓試驗研究；通過對試件荷載-應變曲線、荷載-撓度曲線和滯回曲線等的研究表明，採用該加固方法能有效的約束柱子橫向變形，並對提高鋼筋混凝土柱的極限承載力和延性有明顯的效果；同時根據理論及加固機理分析提出了適應於此加固方法的軸壓極限承載力計算公式。
  19. Deformation is calculated by " mixed method " including curvature and deflection, and uplift is not considered

    在變形分析中，包括曲率和撓度，仍然採用「混合法」 ，並且不計掀起作用。
  20. When cable interacted under the load both of gravity and inertia force, derivative equation of cable ' s defection curve in space is deduced to study cable ' s rigidity movement, and flexible deformation is also determined by finite element method

    分析了懸索上各離散點的位置、速度、加速度和慣性力。推導了在重力和慣性力共同作用下懸索的空間撓曲線微分方程，並研究了懸索的剛體位移和彈性變形。
分享友人
分享到 Line

分享到臉書