擠出模 的英文怎麼說
中文拼音 [jǐchūmó]
擠出模
英文
extrusion die-
The driving rollers are electroplated with hard cr, tension self - controlling of winding - rollers are applied to the driving unit. the barrel of extruder, bullhead tee and die adopt cast aluminum heater which is endurable
擠出機料筒三通和模頭均採用鑄鋁加熱，牽引輥筒電鍍硬鉻，輪鏈輪採用Part i : to provide technical suppt supervise the right technology carryout when the machines, plastic materials moulds are put into injection depart
對投入到擠出部的機器、原料和模具提供技術支持，監督執行正確的擠出工藝。Specification for plastics profile extrusion tooling
塑料異型材擠出模具技術條件Calculatie retention time of plastic melt in extrusion moulding head
塑料熔體在擠出模頭中停留時間的計算We mainly make moulds for injection plastic mould, bumper mould, car lighting mould, pet performs mould, die casting mould, pipe fitting mould, water dripper mould, bottle blowing mould, daily use articles mould, bmc dmc smc mould ect, and the relative daily plastic products
主要以家庭日用塑料品模具各類汽車摩托車配件模具，電器模具，管坯模具，瓶蓋模具，塑料管件模具，塑料注射模具，吹瓶模具，擠出模具，各類bmc dmc smc壓鑄模具，精密模具製造為主。Components of plastics profile extrusion tooling. cover plate
塑料異型材擠出模具零件.蓋板Components of plastics profile extrusion tooling. land plate
塑料異型材擠出模具零件.型板Extrusion plank stuff mould hard plating
擠出模具鍍硬鉻Pressure - type coextrusion die
壓力型多層一次擠出模This function block fem simulation can be used in profile die design, so a new design method of function block comes forth
完成以上步驟后，將上述過程運用於擠出模頭中功能塊結構的設計計算，探討出一種功能塊設計的新型流程的方法。The centre enters the material, the pushing out of the mould head of many patterns, remove and make and converge the line completely, meet the demands of different structure products
中心入料，多型式的擠出模頭，徹底清除製品匯合線，滿足各種結構製品的要求。The section shape of function block structure is usually very complex, and it has no universal formula to calculate and design till now. when making new die, we always design it by experience, and this may bring some inaccuracy. so, it is difficult to improve the quality of the die if only depending on experience
功能塊結構的截面形狀一般較為復雜，對它還沒有形成一個可以通用的數學模型來計算，設計時常根據具體情況，藉助以往的設計經驗進行設計，而這也往往形成了擠出模設計的缺陷，造成了較大的修模量。Components of plastics profile extrusion tooling. t - pin
塑料異型材擠出模具零件. t形銷Components of plastics profile extrusion tooling. die base
塑料異型材擠出模具零件.圓形模座Components of plaastics profile extrusion tooling. round plate
塑料異型材擠出模具零件.圓形模板Experienced with mechanical drawing and extrusion die design
具備機械制圖和擠出模具設計經驗。Terminology of extrusion tooling for plastics
塑料擠出模具術語Components of plastics profile extrusion tooling. rectangular holder
塑料異型材擠出模具零件.矩形模座Specific experience in rubber extruder ， rubber molding press operation and set - up preferable ， and has supervisory experience
有橡膠擠出，模壓成型和工藝設定及管理經驗者優先Components of plastics profile extrusion tooling. rectangular mould plates
塑料異型材擠出模具零件.矩形模板分享友人