擰接頭 的英文怎麼說
中文拼音 [nǐngjiētóu]
擰接頭
英文
coupling screw-up-
The shark was threaded into a pipe "t" connection.
一個螺栓體被擰進一個「T」形管接頭中。Union, screwed - onto, titianium alloy, flared tube
鈦合金擴口式擰入式直通管接頭Reducer, screwed - onto, 90 degree elbow, titianium alloy, flared tube
鈦合金擴口式擰入式變徑直角管接頭Elbow, screwed - onto, 45 degree, titianium alloy, flared tube
鈦合金擴口式擰入式彎管接頭Elbow, screwed - onto, 90 degree titianium alloy, flared tube
鈦合金擴口式擰入式直角管接頭Tee, screwed - onto, titianium alloy, flared tube
鈦合金擴口式擰入式三通管接頭Tee, screwed - onto, asymmetry, flared tube
擴口式不對稱擰入式三通管接頭Elbow, screwed - onto, 90 degree, flared tube
擴口式擰入式直角管接頭Elbow, screwed - onto, 45 degree, flared tube
擴口式擰入式彎管接頭Cross, screwed - onto, flared tube
擴口式擰入式四通管接頭The screw - shell of plug - fuse type fuseholders and the contact of a post - extractor fuseholder adjacent to the mounting surface ( unless the post - extractor fuseholder is of deadfront construction ) shall be connected to the load side of the circuit
臨近盤面安裝的插拔式保險管座的擰動式外殼和柱狀拔出式保險管座的接頭應該接到電路的負荷端上Swiftly wringed tie - in with nut
帶管接螺母的快擰接頭A series of static and fatigue experiments which include lots of specimens are performed on bolted composite laminates that include different sizes, different lay orientations and different torques. dye - enhanced x - radiography is used to check the progressive damage process as evaluation techniques, which can be made nondestructively. finally, the ultimate strength and fatigue life of composite bolted joints in static tension and
層合板接頭的試驗研究考慮了多種幾何尺寸、多種鋪層及不同擰緊力矩對其靜強度及疲勞性能的影響,同時使用滲透劑增強的x射線圖象技術對靜載和疲勞損傷擴展及累積過程進行了無損檢測,並對其進行了分析探討。The wire junction uses plugged bolt to insure its easy operation. it s small in volume and light in weight easy to be installed
2採用對接式接頭,連接時需將連接排插入接頭,擰緊螺栓即可體積小,重量輕,方便安裝。The shark was threaded into a pipe " t " connection
一個螺栓體被擰進一個「 t 」形管接頭中。Connect copper pipes, lines and water pipes with indoor parts. connectors should be tightened to prevent leakage
將銅管、連接線、水管與室內機連接好,銅管接頭必須擰緊,不能有泄漏現象,排水管不能有漏水現象。After the instrument reach the designated position, fastening the union joint
儀表安裝就位后,再擰緊活接頭。The unit shall be equipped with a standard 120v plug - in cord. electrical heating elements shall be screw - in, direct - immersion, stainless steel sheathed, resistance - type. element operation shall be controlled by a thermostat
這種熱水器應該配置一個標準的120伏插頭電纜。電氣加熱元件應該螺紋擰進的,直接浸入式,不銹鋼外層,電阻型加熱元件。加熱元件的工作應該由一個溫控器控制調節。分享友人