支承桿件 的英文怎麼說

中文拼音 [zhīchénggǎnjiàn]
支承桿件 英文
support bar
  • 支 : Ⅰ名詞1 （分支; 支派） branch; offshoot 2 （地支） the twelve earthly branches3 （姓氏） a surname...
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 桿 : 桿名詞（桿子） pole; staff
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  1. The in - plane stability and in - plane equivalent moment coefficient of tapered column

    多個彈性支承上軸心受壓桿件的彈性穩定
  2. 2 ) the structure elements should be laid out symmetrically and uniformly when designing steeve - arch structure, what ' s more, the reasonable selection of section geometric size near the arch foots of first beams is paid attention to and the arrangement difficulties of steel bar due to the big eccentric pressures 2, the analyses of anti - seismic features on transverse direction of the aqueduct l ) the method of adjusting the elements " mass can be harnessed in order to even the layout of seismic loads

    2 ）設計吊桿式拱架支承結構時，各部分構件應當均勻對稱布置。另外，還應注意頭道梁拱腳附近截面的尺寸擬定，克服地震內力造成的大偏心受壓狀態給結構配筋設計增加的困難。 2 、橫槽向抗震性能分析1 ）可利用調整構件質量的方法，使得結構的某些構件的地震荷載分佈均勻一些。
  3. Rolling bearings - needle roller and cage assemblies for connecting rod bearing arrangements

    滾動軸承.連桿支承用滾針和保持架組件
  4. Then, the author provided ways to control flexible support systems " displacement on the base of study the capability of flexible support systems. at the same time, the author analyzed the self - vibrating capability of flexible support systems and study the influence of parameters " changement

    同時，對柔性支承體系的動力性能進行了開拓性的研究，分析了空間柔性支承體系的自振特性，以及矢高、桿件截面、質量等不同參數對其動力特性的影響。
  5. On the contents of two sides abovementined, this paper attempts to do some initial researches from three angles as follows : 1, the analyses of anti - seismic features on longitudinal direction of the aqueduct l ) the seismic longitudinal effects are small. the vibrant characters are decided from the structure integration and rigidness of piers and main arch - ring of the aqueduct, so the following measures should be taken in order to weaken and isolate seismic influence : properly broadening the section sizes and adopting the high class concrete, lowering the height and barycenter of building, setting hoop steel bars so as to increase the plasticity of the concrete which can absorb the seismic energy and prevent the damages due to stress centralization on the linkages and changing place

    本文試圖就上述的這兩大方面的內容，從以下三個角度進行了初步研究： 1 、縱槽向抗震性能分析1 ）湯峪河吊桿拱支承結構的縱槽向地震效應較小；吊桿式拱架結構動力特性取決于槽墩和主拱圈的剛度，以及結構的整體性，故適當加大構件截面尺寸或提高砼標號，盡量降低結構的建築高度和重心，在構件連接和變截面處增設梗脅，按照約束混凝土的要求來加強箍筋的配置，增加砼的延性，以克服地震時構件連接和變截面處的應力集中造成的坡壞，並吸收大量的地震能量，從而起到隔震，減震的效果。
  6. When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved

    分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。
  7. Generally, the skew bridge ' s calculation theories can be divided into three types : the category 1 is the plank theories method, such as the finite difference method, the finite element method and the finite strip method, etc ; the category 2 is the beam theories, such as the grid beam theories, the general grid theories, the rigid cross - beam method, the elastically - supported continuous beam method and the bar system analytical method, etc ; the category 3 is the practical method, such as the g - m revising method, the grid - beam simple method and ghali form coefficient method, etc

    目前關于斜梁橋的計算理論和方法概括起來，大致可以分為三類：第一類為板理論方法，如有限差分法、變分法、有限單元法、有限條法等；第二類為梁理論法，如格構梁理論、一般格構理論、剛性橫梁法、彈性支承連續法、桿件結構的分析方法；第三類為實用計演算法，荷載橫向分佈的計算方法如g ? m修正法、格構梁的簡易法、 ghali表格系數法等。
  8. The possible shear of the upper chord will change beam from flexural member to member under flexure and compression force. this is emphasised through design example. as a result ， we find that composite floor system is good for reducing the height of floor system

    在組合樓蓋體系設計中，筆者指出，可能的桁架弦桿剪力會使作為桁架弦桿側向支承的梁由彎曲構件變為壓彎構件，這是在與桁架體系相適應的樓蓋體系設計中應該注意的一個環節。
  9. The dissertation discusses some theories of computation including the unit stiff matrix of the spatial member in the local coordinates ， the coordinate transformation, the integration of the integer stiff matrix ， the equivalent joint load ， the introduction of the boundary condition ， the computation of the unit internal force and support reaction ， the stableness of the spatial stiff frame. the dissertation also discusses the methods of dealing with several unusual problems such as combined structure, temperature stress ， elastic bearing

    本文論述了空間桿件局部坐標單元剛度矩陣、坐標轉換、整體剛度矩陣的集成、等效結點荷載、邊界條件的引入、單元內力與支座反力計算、空間剛架穩定的計算理論，以及組合結構、溫度內力、彈性支承等幾個特殊問題的處理方法。
  10. To carry out computer program of bending bar, mathematical model of calculating support constraint forces is deduced from dynamic model of bending bar and superposition principle

    摘要根據承彎桿件的力學模型，利用疊加原理，推導出計算支座約束力的數學模型，它是實現承彎桿件計算機程序設計的前提。
  11. In this paper, the studied works are list as follows : 1 ) the theory of elastically supported continuous beam method is brought forward to transfer spatial continuous beam - arch composite bridges into plane structure. the plane finite element method is used to calculate inner forces and deflections of each beam and arch. at the same time, spatial finite element model is created for contrast

    研究提出用彈性支承連續梁法荷載橫向分佈理論計算空間梁拱組合式橋梁的荷載橫向分佈，從而將空間問題轉化為平面計算問題，進而用平面桿系有限元理論分析求解梁拱拱片各桿件截面的內力和撓度，並用空間有限元理論和通用程序建立空間模型進行對比計算。
  12. At last, with the stiffness method, the effect of diaphragm density on restraining the distortion of thin - walled bar is analyzed. with different load cases of uniformly load and concentrated load and different boundary conditions of two fixed ends and two simply supported ends and cantilever, the distortion and torsion of the same rectangle thin - walled girder is examined

    在均布和集中兩種反對稱荷載情況下，按兩端固定、兩端簡支和懸臂三種不同的支承情況，採用剛度法對同一矩形截面薄壁桿件的畸變和剛性扭轉分別進行分析。
  13. Because slts owns too many parts and complex supporting conditions, and invalidation of few parts or nodes does not have significant effect for structural bearing capacity, research orientation is transferred to structural support system in chapter 4 of the thesis. limited loading capacity and safety index of steel bracket of slts are calculated and analyzed for providing theoretic upper limit to safe operation of support system

    由於網架結構的桿件眾多，結構支撐條件復雜，少數桿件或節點的破壞對于結構的正常承載無顯著影響，本文在第四章將研究方向轉向網架結構的支撐體系，計算分析網架結構支撐鋼牛腿的極限承載能力和安全儲備，為支撐系統的正常工作提供一個理論上限。
  14. This paper discusses the performance of load bearing under different boundary conditions by model test and finite element analysis. the x - side binding of the supporting surface connecting with up - side chord member of slice arch is the most important factor that affects membrane effect of the slab. the load bearig capacity of the slab with fixed end increased forty percent of the capacity of the simple - supported slab, because membrane effect of the slab with fixed end is remarkable

    本文通過模型試驗和有限元分析，較深入地探討了在不同邊界條件下微彎板的受力性能，結果發現與拱片上弦桿連接的支承面有側向約束條件是影響微彎板的薄膜效應最重要的因素，當該支承面為固結狀態時，薄膜效應十分顯著，其承載力比簡支約束微彎板的承載力提高了約40 。
分享友人
分享到 Line

分享到臉書