支承桿 的英文怎麼說

中文拼音 [zhīchénggǎn]
支承桿 英文
bearing-out spar
  • 支 : Ⅰ名詞1 （分支; 支派） branch; offshoot 2 （地支） the twelve earthly branches3 （姓氏） a surname...
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 桿 : 桿名詞（桿子） pole; staff
  1. If the superstructure is crossways, make sure that the foot section is not lying on the track groups or the outrigger struts of the auxilliary support ( if required, props up the boom to a higher level )

    如果上車為十字交叉型的，則務必確保臂桿根部沒有接觸到履帶組或輔助支承上的支腿壓桿（如夠必要，可把臂桿墊得更高些） 。
  2. The in - plane stability and in - plane equivalent moment coefficient of tapered column

    多個彈性支承上軸心受壓桿件的彈性穩定
  3. The mechanism consists of a steering gear box, pitman arm, drag kink, tie rods, steering arms, and steering knuckles, the latter supporting the front wheels

    該機構由轉向器，轉向垂臂，縱拉桿，轉向橫拉桿，梯形臂和轉向節構成，轉向節支承著前輪。
  4. As a brand new supporting structure, the steeve - arch was firstly used in the design of tangyu aqueduct ( also used as a bridge ) lies on the eastern main ditch of shitou river, shaanxi province

    吊桿式拱架作為一種新型拱式支承結構在陜西省石頭河東乾渠湯峪渡槽（橋渡結合工程）設計中首創應用。
  5. 2 ) from the angle of constructing course, steeve - arch supporting structure requires low - capacity cranes to erect, and simple constructing methods easy to meet. the time spending on construction is short. the usual arch supporting structure requires high - capacity cranes to erect, and complicate constructing methods hard to meet

    2 ）從施工角度看，吊桿式拱架支承結構對吊車的起吊能力要求低，工藝簡單，施工方便，工期短；豎桿式拱架支承結構起頂重量大，對吊車的起吊能力要求高，施工難度大。
  6. 2 ) the structure elements should be laid out symmetrically and uniformly when designing steeve - arch structure, what ' s more, the reasonable selection of section geometric size near the arch foots of first beams is paid attention to and the arrangement difficulties of steel bar due to the big eccentric pressures 2, the analyses of anti - seismic features on transverse direction of the aqueduct l ) the method of adjusting the elements " mass can be harnessed in order to even the layout of seismic loads

    2 ）設計吊桿式拱架支承結構時，各部分構件應當均勻對稱布置。另外，還應注意頭道梁拱腳附近截面的尺寸擬定，克服地震內力造成的大偏心受壓狀態給結構配筋設計增加的困難。 2 、橫槽向抗震性能分析1 ）可利用調整構件質量的方法，使得結構的某些構件的地震荷載分佈均勻一些。
  7. Abstract : the calculation of the rigidity for the ball screw transmission system was discussed, including the axial rigidity of the screw, the axial rigidity of supporting bearing, the contact rigidity between ball and groove. the influence of the rigidity variation on the transmission accuracy was analyzed

    文摘:本文系統地討論了滾珠螺旋傳動系統的剛度計算，包括螺桿本身的軸向剛度、螺桿兩端支承軸承的剛度以及滾珠與滾道間的接觸剛度，並分析了剛度變化對傳動精度的影響。
  8. The work in this thesis mainly includes following parts : 1. as for box girder cross section, the three - bar stimulation method under typical loads and supports has been introduced. the force and stress formulae for flanges have been derived from the three - bar method. by reasonable simplification for multi - cell box girder, the three - bar method has been applied in multi - cell box girder ' s shear lag analysis

    對于箱形截面主梁，本文介紹了三桿比擬法上、下翼板中比擬桿的計算公式，以及在典型荷載和支承的情況下翼板內各桿的應力計算公式，並對多箱式主梁截面進行合理簡化，使三桿比擬法應用於多室箱梁的剪力滯分析。
  9. Rolling bearings - needle roller and cage assemblies for connecting rod bearing arrangements

    滾動軸承.連桿支承用滾針和保持架組件
  10. Then, the author provided ways to control flexible support systems " displacement on the base of study the capability of flexible support systems. at the same time, the author analyzed the self - vibrating capability of flexible support systems and study the influence of parameters " changement

    同時，對柔性支承體系的動力性能進行了開拓性的研究，分析了空間柔性支承體系的自振特性，以及矢高、桿件截面、質量等不同參數對其動力特性的影響。
  11. A study on the method of damage recognition of free - spring bar

    彈性支承桿損傷識別方法研究
  12. On the contents of two sides abovementined, this paper attempts to do some initial researches from three angles as follows : 1, the analyses of anti - seismic features on longitudinal direction of the aqueduct l ) the seismic longitudinal effects are small. the vibrant characters are decided from the structure integration and rigidness of piers and main arch - ring of the aqueduct, so the following measures should be taken in order to weaken and isolate seismic influence : properly broadening the section sizes and adopting the high class concrete, lowering the height and barycenter of building, setting hoop steel bars so as to increase the plasticity of the concrete which can absorb the seismic energy and prevent the damages due to stress centralization on the linkages and changing place

    本文試圖就上述的這兩大方面的內容，從以下三個角度進行了初步研究： 1 、縱槽向抗震性能分析1 ）湯峪河吊桿拱支承結構的縱槽向地震效應較小；吊桿式拱架結構動力特性取決于槽墩和主拱圈的剛度，以及結構的整體性，故適當加大構件截面尺寸或提高砼標號，盡量降低結構的建築高度和重心，在構件連接和變截面處增設梗脅，按照約束混凝土的要求來加強箍筋的配置，增加砼的延性，以克服地震時構件連接和變截面處的應力集中造成的坡壞，並吸收大量的地震能量，從而起到隔震，減震的效果。
  13. The affection of continuous bridge deck and elastic support to inner force of suspender is ignored

    該設計忽略了橋面連續及彈性支承對吊索（桿）內力的影響。
  14. The biggest difference from the usual down bearing arch structure lies in this points that the four tectonic cracks on its two down beans ca n ' t constrain the level forces

    它與常規的下承式拱架支承結構的最大區別在於它的兩道下弦桿設置了四道斷縫，從而使下弦桿失去對拱腳水平力的約束作用。
  15. Racks, awnings, planters, supporting platforms for air conditioners, eaves, mouldings, projections, architectural features, drying racks, railing, advertising signs etc

    支架遮篷花槽冷氣機支承平臺屋檐裝飾條子伸出物建築裝飾晾衣架欄桿招牌等
  16. When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved

    分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。
  17. Generally, the skew bridge ' s calculation theories can be divided into three types : the category 1 is the plank theories method, such as the finite difference method, the finite element method and the finite strip method, etc ; the category 2 is the beam theories, such as the grid beam theories, the general grid theories, the rigid cross - beam method, the elastically - supported continuous beam method and the bar system analytical method, etc ; the category 3 is the practical method, such as the g - m revising method, the grid - beam simple method and ghali form coefficient method, etc

    目前關于斜梁橋的計算理論和方法概括起來，大致可以分為三類：第一類為板理論方法，如有限差分法、變分法、有限單元法、有限條法等；第二類為梁理論法，如格構梁理論、一般格構理論、剛性橫梁法、彈性支承連續法、桿件結構的分析方法；第三類為實用計演算法，荷載橫向分佈的計算方法如g ? m修正法、格構梁的簡易法、 ghali表格系數法等。
  18. The possible shear of the upper chord will change beam from flexural member to member under flexure and compression force. this is emphasised through design example. as a result ， we find that composite floor system is good for reducing the height of floor system

    在組合樓蓋體系設計中，筆者指出，可能的桁架弦桿剪力會使作為桁架弦桿側向支承的梁由彎曲構件變為壓彎構件，這是在與桁架體系相適應的樓蓋體系設計中應該注意的一個環節。
  19. Against classical dynamic balancers of crank and connecting rod mechanism, the test system has virtue hereinafter : ( 1 ) supporting structure adopt projecting beam uniquely. the signal of vibration provoked by crank and connecting rod mechanism revolving is concentrated to strain beam. the signal is not only abundance, but also easy to test and the test sensitivity is great

    與傳統的曲柄連桿機構動平衡機相比，這種測試系統具有以下優點：支承結構採用獨特的懸臂梁式結構，曲柄連桿機構在運轉過程中振動規律完全映射到支承梁的應變上，振動信號豐富且易測試、靈敏度高。
  20. The dissertation discusses some theories of computation including the unit stiff matrix of the spatial member in the local coordinates ， the coordinate transformation, the integration of the integer stiff matrix ， the equivalent joint load ， the introduction of the boundary condition ， the computation of the unit internal force and support reaction ， the stableness of the spatial stiff frame. the dissertation also discusses the methods of dealing with several unusual problems such as combined structure, temperature stress ， elastic bearing

    本文論述了空間桿件局部坐標單元剛度矩陣、坐標轉換、整體剛度矩陣的集成、等效結點荷載、邊界條件的引入、單元內力與支座反力計算、空間剛架穩定的計算理論，以及組合結構、溫度內力、彈性支承等幾個特殊問題的處理方法。
分享友人
分享到 Line

分享到臉書