支臂軸 的英文怎麼說

中文拼音 [zhībèizhóu]
支臂軸 英文
support arm shaft
  • 支 : Ⅰ名詞1 （分支; 支派） branch; offshoot 2 （地支） the twelve earthly branches3 （姓氏） a surname...
  • 臂 : 臂名詞1. （胳膊; 從肩到腕的部分） arm 2. （人體解剖學上多指上臂） upper arm
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  1. The trunnion assembly is supported by air bearings at the end of each arm and is held in position by brake shoes at each bearings.

    耳軸組件的支承是每根臂末端的空氣軸承，軸承上的閘瓦起定位作用。
  2. We mainly produce shifting fork and release fork of large - scale and heavy - duty truck ; shifting fork, release fork, shifting block, choosing - gear shaft, reverse - gear shifting fork shaft, right - and - lfet steering joint arm, upper cross arm shaft, wheel hub, link rod of all kinds of cars right - and - left supports, nipbutton of train auto - girder parts ; centeral wedge, fixed lean - board of absorber ; shifting fork, erankshaft, link rod, under - link board, startup pole of motocycle ; mould forging of mine, construction machinery, textile machinery, non - ferrous metal industry, etc

    主要生產產品：大、重型卡車變速箱的撥叉、分離叉等；各種轎車變速箱的撥叉、分離叉、撥塊、選檔軸、倒檔撥叉軸、左右轉向節臂、上橫臂軸、輪轂、聯桿，火車自動梁部件的左右支柱、夾扣，減震器的中心楔塊、固定斜板等鍛件；摩托車的撥叉、曲軸、連桿、下聯板、啟動蹬桿總成；礦山機械、建築機械、紡織機械、有色金屬等精模鍛件。
  3. For the cantilever beam, the theoretical stiffness and limited capacity are slightly less than the test ones if considering only the steel beam and the reinforced bars in the negative moment zone with the concrete in the tension zone ignored

    結果表明：簡支組合扁梁，忽略彈性中和軸以下受拉的混凝土的影響，採用等效換算截面方法計算所得的剛度和極限承載力與試驗結果比較吻合；懸臂梁只考慮混凝土板中配置的負彎矩鋼筋，忽略混凝土，計算所得的剛度和極限承載力比試驗結果略微偏小，但相差不大。
  4. Through the experimentation for the physical performance of cfpb masonry under local compression, the author has observed the deformation and failure of cfpbm. based on the mathematical statistics and regression analysis of the experimental data, the author derived a feasible and common formula for counting the cfpbm ' s local compression strength regarding the different local compression locations, analyzed stress distribution of local bearing masonry under beams end, and provided the calculating formula on effective supporting length of beam end in brick masonry. as the results of experiments demonstrate, owing to the cfpb ' s own holes " system, the beneficial effects, the bounding effect of surrounding masonry and the spread effect of force, have not developed completely

    試驗結果分析表明：由於多孔磚自身的孔洞結構，砌體內部的圍箍作用和力的擴散作用未得到充分發揮，局壓強度雖較軸心受壓強度有所提高，但仍低於同情況下實心磚的局壓強度；當有上部荷載作用時，對砌體局壓有利的懸臂卸荷作用和內拱卸荷作用均不明顯，因此在推導梁端局壓強度計算公式時，未考慮此可能存在的有利影響，計算偏安全；局壓強度提高系數公式除採用規范公式（二項式）的表達式，還用對數式進行了回歸推導，得到了一個較為普遍的公式；論文還對梁端局壓的梁端有效支承長度計算公式進行了回歸推導。
  5. Compared with the traditional cantilever structure, the bearing life of two - terminal bracing structure is improved by 17. 51 times, while the contact stress of gear tooth is reduced by 45. 7 %, and the bending stress of gear tooth is reduced by 62. 8 %

    與傳統主動齒輪懸臂結構相比兩端支撐結構的軸承壽命提高了17 . 51倍、輪齒接觸應力降低45 . 7 % 、輪齒齒根彎曲應力減小62 . 8 % 。
分享友人
分享到 Line

分享到臉書