收縮嘴 的英文怎麼說
中文拼音 [shōusuōzuǐ]
收縮嘴
英文
constricting nozzle-
Rail corrugation at high frequency wheel rail interaction
小口徑軸對稱收縮噴嘴射流沖擊大平板噪聲指向特性研究Contraction of the zygomatic major muscle elevates and retracts the corner of the mouth, while the depressor labii inferioris pulls the lips down and out
大顴肌控制嘴角的延展和收縮動作，降鼻翼肌則負責使上下唇上下移動。A reasonable position of driving nozzle helps to achieve the maximum material flow that also depends on other parameters such as backpressure, properties of conveyed material and driving gas. it is observed that, an increase of convergent section angle is harmful to the pneumatic conveying system, and also influences on the mass flow rate of conveyed material, the distribution of static pressures in injector and the pressure drops of conveying pipe. in addition, within a reasonable scope of air mass rate, increasing the driving jet velocity is more advantageous than enlarging the dimension of driving nozzle
試驗研究發現，氣體噴嘴位置對氣固噴射器的輸送能力影響最大，氣體噴嘴存在某一最佳位置，而這一最佳位置與背壓、輸送物料特性和輸送風特性相關聯；氣固噴射器的收縮角對其輸送能力、內部靜壓分佈和輸送管阻力特性均有適量影響，收縮角增大對整個輸送系統均不利；在適當的輸送風范圍內，提高氣體噴嘴出口速度比擴大氣體噴嘴尺寸更為有利，但氣體噴嘴出口速度過高會增加氣固噴射器和輸送管內的能量損耗，給輸送帶來不利的影響；系統背壓與氣固噴射器的氣體噴嘴出口速度的選取有關。And they mean it : they smile with their eyes ( a contraction of the orbicularis oculi facial muscles ), not just their mouths
這意味著：他們用眼睛微笑（面部上瞼提肌肌肉的收縮） ，而不僅僅是他們的嘴。His jaw instinctively closed, and his gray eyes narrowed.
他本能地閉緊嘴巴，灰色的眼睛收縮成一條線。The influences of the inlet tube angle, backpressure and driving jet velocity on static pressure distribution in the gas - solid injector are calculated, and the effects of the inlet tube angle on particle bulk phase concentration and axial mean speed of particles in the gas - solid injector are analyzed firstly. the predicament caused by lack of measuring means on the particle velocity in experiments is solved
分析了收縮角、背壓和氣體噴嘴出口速度對氣固噴射器內靜壓分佈的影響，以及收縮角對氣固噴射器內固體顆粒體積濃度場和顆粒平均速度的影響，解決了噴射器內固體顆粒速度試驗測試手段缺乏的困境。According to the rheological properties of melted abs filament during extrusion from fdm ' s nozzle, on the basis of research on extruded filament section shape, the compensation model of ideal contour line is established, and a new technique for compensating inner or outer contour line of workpiece is put forward, which should depend on the real width of extruded filament ( instead of nozzle radius ) and the real dimensional shrinkage of workpiece
根據abs絲從噴頭擠出過程中的流變性能，在研究fdm工藝噴頭擠出絲截面形狀的基礎上，建立了理想輪廓線的補償模型，並提出了根據擠出絲實際寬度（而非噴嘴孔直徑）和零件尺寸實際收縮量補償零件內、外輪廓的新方法，驗證試驗結果表明該補償模型和補償方法正確可行。分享友人