收縮形狀 的英文怎麼說

中文拼音 [shōusuōxíngzhuàng]
收縮形狀 英文
contraction shape
  • 收 : Ⅰ動詞1 （把攤開的或分散的事物聚集、合攏） put away; take in 2 （收取） collect 3 （收割） harvest...
  • 縮 : 縮構詞成分。
  • 狀 : Ⅰ名詞1 （形狀） form; shape 2 （情況） state; condition; situation; circumstances 3 （陳述事件或...
  • 收縮 : 1 （由大變小; 由長變短） contract; shrink 2 （緊縮） concentrate one s forces; draw back 3 take u...
  1. They are closely related to the growing environment regarding to the rhizome with remnant stem scars, adventitious roots, taproot shrink wrinkles, and fibrous roots

    人參的根莖及殘莖痕、不定根、主根的收縮紋和須根分佈形態等與環境和生長年限的關系尤為密切，但各種性狀之間存在著變異的規律性和相關性。
  2. It is most important to recognize the characteristics including cylindrical section of rhizome ( yuanlu ), drooping adventitious root tuber ( xiachuiding ), wirelike wrinkles on tap shoulder ( tiexianwen ) and some slender pliable warty fibrous roots ( zhenvuxu )

    、主根肩部的線形收縮紋（鐵線紋）及帶疣狀突起的細長柔韌的須根系（珍珠須）是最重要的鑒別性狀。
  3. On the surface of phbv spherulite, some concentric ring like patterns will occur. based on the procedure of the formation of ring - like patterns, the possible mechanism is given

    在球晶的表面出現有同心圓環狀條紋，經實驗驗證為表面的不平整所導致，形成機理主要可能是結晶過程中的體積收縮。
  4. Through the experiment of the interfacial bonding shear strength and the shrinkage strain of concrete, the influence of the interfacial roughness of used concrete surface and interfacial bonding agent to interfacial bonding strength is revealed ; new concrete component and the shape and size of concrete slab are main factor affecting the shearing stress in layers

    試驗結果表明：老混凝土粘結面的粗糙度和界面粘結劑類型對新老混凝土界面粘結強度影響很大；新鋪混凝土材料和混凝土路面板形狀尺寸是影響新老混凝土粘結面收縮剪應力的主要因素。
  5. A myocardial bridge simulator is made and an experimental model is built to simulate and study the blood pressure and the blood flow under the compression state

    摘要利用研製的心肌橋模擬裝置，對冠狀動脈受壓迫狀態建立了圓形收縮的實驗模型，進行了冠狀動脈受心肌橋壓迫持續到舒張期情況下的血壓和流量模擬實驗。
  6. The camber development mechanism and the influence factors were researched by geometry analysis, viscous analysis and sintering kinetics analysis. the camber model was established and the equation for calculating curvature of camber was proposed. the influence factors for camber involve the original size of composite, the sintering properties and the shrinkage mismatch between the two materials

    從幾何學、粘彈性力學和燒結動力學的不同角度出發，探討了共燒翹曲形成機制和影響因素，建立了介電材料鐵氧體材料疊層共燒翹曲模型和翹曲曲率方程，揭示影響翹曲的因素為形狀尺寸因子，材料的燒結特性和異種材料之間的收縮率差，其中燒結過程的收縮率差是翹曲產生的根本因素，收縮率差越大，則翹曲曲率越大。
  7. The hukou waterfall on the huanghe river west of jixian county, shanxi, is formed when the river flows to the hukou mountains on the shanxi - shaanxi border and its 250 - meter - wide bed, sandwiched between the canyons on its banks, abruptly narrows into a trough 50 meters wide and 30 meters deep and falls down into a big stone - strewn pool

    當流至壺口時，寬約400多米的河床，突然收縮到四五十米，形成特大型馬蹄狀瀑布，河水似從一巨型壺口瀉下。主瀑布寬40米，落差近50米。
  8. On the basis of relative researches in the world, according to the study status of steel - concrete composite slab, which would be widely used in modern bridge, modified equivalent inflexibility of steel - concrete composite slab was deduced by use of conversion section principle in this paper ; based in this, this paper put forwards the theory of ultimate flexural capacity of steel - concrete composite slab in consideration of slip effect, and introduces the practical simplified method for calculating flexural deformation of steel - concrete composite slab in consideration of the effect of steel studs and welded wire, and conclude that the methods in this paper is veracious and reliable, comparing with the traditional calculating mode ; morever, this paper put forwards the calculating theory and program of the effect analysis of creep and shrinkage to steel - concrete composite slab, using conversion elastic modulus principle, and testifies that the theory is right and the program is reliable and practical

    本文在國內外研究成果的基礎上，針對壓型鋼板與混凝土組合板結構在現代橋梁建設中廣泛應用前景和研究現狀，利用換算截面法導出了壓型鋼板與混凝土組合板結構的修正等效慣性矩；在此基礎上，又推出了考慮壓型鋼板與混凝土之間的相對粘結滑移影響的壓型鋼板與混凝土組合板結構極限抗彎承載能力計算理論，並介紹了考慮栓釘、聯結件影響的壓型鋼板與混凝土組合板結構簡化實用撓曲變形計算公式，而且通過與傳統計算理論的分析比較，表明本文提出的計算理論公式的準確可靠性；此外，採用換算彈性模量比法著重提出了壓型鋼板與混凝土組合板結構的徐變、收縮效應分析的計算理論和程序，並通過實例分析計算證明了理論的正確性、程序的可靠性和實用性。
  9. In order to research product properties of the cross wedge rolling ( cwr ), a series of rolling experiments have been carried out on two - roller cwr under the condition of considering the variation of the original diameter, deformation temperature, area reduction and heat treatment methods and so on

    摘要為了研究楔橫軋條件下工件的性能，在考慮原始棒料直徑、變形溫度、斷面收縮率以及工件軋后熱處理狀態等的基礎上，利用二輥楔橫軋機進行了系列楔橫軋軋制實驗。
  10. Based on the characteristics of silicon whisker, the research on the modification of pa6 by silicon whisker sio2 - jx was made, and the result showed that the tensile strength, impact strength, brinell hardness, and heat resistance increased with the increase of the content of the whisker ; sio2 - jx could replace short glass fiber in the modification of pa6, improving the heat distortion temperature, removing the appearance of glass fiber, reducing shrinkage and the cost

    摘要利用晶須矽纖維狀的特性，對其填充于龍玻纖改性進行研究，結果表明，隨晶須用量的增加，材料的拉伸強度、沖擊強度，布氏硬度、耐熱溫度均得到提高；晶須矽可取代短玻纖使用，提高熱變形溫度、消除玻纖外露，降低收縮率及生產成本等。
  11. With the different loading ratio of parallel to axis and normal to axis direction, damage defects will occur bulking problem. by varying the degree of material anisotropy relative to the loading axis such as poisson ' s ratio and shear modulus, crack growth bulking strain value parallel to or normal to the loading axis is different. the parameters controlling the growth or arrest of the delamination damage are identified as the geometry and the depth of defects and radius of cylindrical etc. at last, it was investigated that the delamination damage is often induced by the tip of matrix damage under higher stress

    研究結果表明:殼體筒段受軸向拉伸和內壓載荷作用時，軸向和環向載荷的比率不同，母層和子層可能發生拉伸屈曲，也可能發生收縮屈曲，或者同時發生拉伸和壓縮屈曲;母層與子層各向異性存在差異，即泊松比與剪切模量不匹配時，將使子層板的邊界上承受壓縮和剪切作用，當分層達到臨界狀態則發生屈曲，當母層與子層的各向異性差異越大，則發生分層屈曲的可能性越大;分層損傷的屈曲應變值與子層自身的彈性模量、分層子層的形狀、厚度以及圓柱半徑等因素有關。
  12. First according to the fact that tangential components of the evolution do not affect the geometric shape of the evolving curves, we introduce the evolution equation of geometric quantities for the general planar curves. then we describe the work of gage - hamilton briefly. last we consider a special curvature flow of curve which evolves with speed function of the principal curvatures along the inner norm and show that convexity of the curve is kept and its length and area are contracted if the initial closed curve is smooth and convex. so the final shape of the curve will be a point in finite time

    首先根據曲線在切向分量上發展是不影響曲線的發展形狀，我們引入了曲線的一些幾何變量的發展方程；其次我們簡要地回顧gage - hamilton研究曲線發展的一般步驟；最後我們考慮沿曲線的內法線以曲率的函數為發展速度的一類特殊的曲線族，證明了在初始曲線為凸的閉平面簡單曲線條件下，曲線將保持凸的，並且它的面積和周長將同時收縮，並在有限時間內成為一個點。
  13. In lifting - surface theory, the non - liner phenomena of the trailing vortex in the transition wake area and of the tip vortex separation are considered. in surface panel method hyperboloidal quadrilateral panels are employed and the morino ' s analytical formulation is used to determine the influence coefficients. the more reasonable pressure kutta condition is satisfied at the trailing edge of propeller blade

    在計算中，對于升力面理論，本論文考慮了過渡區尾渦收縮和葉梢分離的非線型現象的影響；對于面元法，本論文採用的是計算較為簡便的基於擾動速度勢的基本公式及雙曲面形狀的面元，在槳葉隨邊滿足更趨合理的壓力kutta條件，並用morino導出的解析公式計算面元的影響系數的快速有效的數值預報方法。
  14. The material has good flexibility and elasticity, can be suitable to the unfolding and shrinkage of the base level, and freely change the shape but no crack

    該材料具有良好的彈性和柔韌性，可適應基面的折展與收縮，自如地改變形狀而不開裂。
  15. Locally, volumes suffer minimal distortion, and no shape jittering or wobbling happens : other methods do not necessarily have these desirable properties. we also show how to control the method so that changes of shape in particular, size changes vary linearly with time

    實驗證明，本文方法得到的三維實驗結果光滑均勻，視覺感覺良好，在其它漸變演算法中經常發生的形狀的收縮形狀抖動等現象在本文方法中不會發生。
  16. Upon contraction, the rotation of the cloud and the collisions between the particles in cloud would flatten the cloud to a disk, called the

    這團氣體的收縮，導至旋轉速度增加，再加上氣體粒子之間的摩擦，令氣體團變形成為碟狀，我們稱之為
  17. The alteration of hemodynamic factors that arise from contraction of the myocardial bridge greatly affects the evolution of atherosclerosis through the regulation of intimal lipid infiltration within the artery

    因此處血管收縮導致的血行動力改變，大幅地影響粥狀硬化的形成及內膜脂質浸潤的調控。
  18. This algorithm adopts a middle ground between centroid - base and all - points - based approaches. instead of using a single centroid or all points to represent a cluster, a fixed number of representative points in space are chosen, these points represent and capture the geometry and shape of the cluster. in addition. the representative points of a cluster are generated by first selecting well - scattered objects for the cluster and then " shrinking " or moving them toward the cluster center by a specified fraction, or shrinking factor. the shrinking helps dampen the effects of outliers. therefore, cure is more robust to outliers

    該演算法選擇基於質心利基於代表對象方法之間的中間策略，它不用單個質心或簇中全部對象米代表一個簇，而是選擇數據空間中定數目的只有代表性的點，這些點代表和捕捉到了簇的形狀。此外，由於引入了收縮因子使代表點向簇小心「收縮」而使該演算法能夠較好地消除孤立點的影響，在處理孤立點上也更加健壯。
  19. The indented form requires the first word of each line to be indented one or two blocks, thus shaping the form of the inverted ladder

    縮進式要求信頭和收信人地址均較上行縮進一至兩個字母，成倒階梯形狀。
  20. Pof ' s shrink rate is so high that it fits for packing the products with all kinds of shapes and sizes

    快而高的收縮率，適用於包裝各種形狀和尺寸的產品
分享友人
分享到 Line

分享到臉書