故障特徵 的英文怎麼說

中文拼音 [zhàngzhǐ]
故障特徵 英文
fault signature
  • : Ⅰ名詞1 (事故) event; incident; happening; accident 2 (原因) cause; reason 3 (朋友; 友情) fr...
  • : Ⅰ動詞(阻隔; 遮擋) block; hinder; obstruct Ⅱ名詞(遮擋物) barrier; block; obstacle
  • : Ⅰ形容詞(特殊; 超出一般) particular; special; exceptional; unusual Ⅱ副詞1 (特別) especially; v...
  • : 名詞[音樂] (古代五音之一 相當于簡譜的「5」) a note of the ancient chinese five tone scale corre...
  • 故障 : hitch; breakdown; stoppage; fault; faulting; accident; blunder; bug; conk; failure; impairment; i...
  • 特徵 : characteristic; feature; properties; aspect; trait
  1. Because the fault of field windings turn - to - turn shorted do not cause much effect of the operation of the machine or its fault characteristics are not very clear, most of the faults are neglected

    轉子匝間短路對機組正常運行影響不大或故障特徵不明顯,因此許多匝間短路被忽略了,但長期運行匝間短路會導致轉子線圈一點甚至兩點接地。
  2. Fast algorithms of both discrete and orthonormal wavelet and wavelet packet coefficient are diagrammatized to be introduced. daubechies wavelet is applied to help to discuss the application and test on signal filtering and noise reduction with the principle and threshold implementation ; the basic principle to pickup the fault characteristics is introduced mainly about the relations between the maximum module and signal saltation point and how to characterize the saltation point with lipschitz exponent

    展示了離散正交小波變換的mallat快速演算法和小波包系數分解的快速演算法;重點應用daubeches小波探討了小波變換在信號濾波去噪中的應用和實驗,闡述了其基本原理和通過閾值化處理實現濾波的具體方法;探討了用小波變換進行故障特徵提取的原理,說明了小波變換模極大值和信號突變點之間的關系以及怎樣用李氏指數來表突變點的性質。
  3. Adopting the method of time domain and frequency range, the breakdown characteristic signal is analyzed, and the information of the abnormal state of valve clearance is obtained

    並採用時域,頻域的分析方法對故障特徵信號進行分析,從而得到氣門間隙異常狀態的信息。
  4. The reassigned smoothed pseudo wigner - ville distribution ( rspwvd ) is introduced, which has less interference and higher resolution than other time frequency distributions like wigner - ville, choi - williams etc. it is used to detect the multi - knocking of engine such as cylinder, piston pin, valve, crank bearing, connecting rod bearing and jib knocking. a new fault diagnosis technique based on the rspwvd for the engine multi - knocking problem is proposed. by comparing the bispectrum and bicoherence of the gear vibration signals, it is demonstrated that bispectrum has an advantage over bicoherence for feature extraction of such signals

    第四章首次引入一種重分配方法,得到干擾項少而解析度高的重分配平滑偽魏格納維爾分佈( rspwvd ) ;對發動機曲軸主軸承響、連桿軸承響、活塞銷響、活塞敲缸響、氣門響和挺桿響等常見機械異響振動信號進行了全面地比較分析;通過對各種異響故障特徵信號的分析研究,提出基於rspwvd的發動機多異響診斷策略,利用該策略可以準確識別不同的發動機異響
  5. In this paper, it has been studied based on the fractal theory, multi - fractal theory, calculation and analysis of each fractal dimension and general dimension being set as fault feature that fault diagnosis and identification of rotating model and steam - electric generating set

    本文基於分形理論、多重分形理論,通過對各分形維數的計算分析,把廣義分形維數作為故障特徵量,對旋轉機械模型及汽輪發電機組的診斷與識別進行了研究。
  6. The thesis expatiated the behavioral and complicated degree in machine first, and to evaluate the degree of complexity of running condition, proposes two methods : qualitative graphic method - recurrence plot and quantitative estimation criterion. both method can effectively describe the complexity of running condition. the predictability of running condition based on these two methods is also discussed

    論文首先闡述了機組狀態行為的復雜程度,並對如何評價機組這一總體故障特徵進行了研究,從定性和定量的角度上分別提出了圖形描述工具?遞歸圖和定量評估指標兩種方法,並結合這兩種方法討論了機組行為的可預測性問題。
  7. Through analysising the characteristics of the power system with floating neutral point deeply, the paper puts forward a new plan of single - phase to ground fault line selection on the base of s ' s signal injecton method and gives the hardware and software design. in this design, the high speed sampling and data processing is carried out through using dsp processor ; the large electrice current is drived through the application of a high - performance audio power amplifier and transformer ; the communication between host computer and detectors is realized through rs485 bus technology ; the difference multilevel frequency - selected amplifier is designed and the feeble signal of space is sampled on the base of the theory of magnetic induction ; the interface between dsp and exterior chip and rs485 interface logical is designed through using fpga ; the using of lcd module and keyboard interfacing chip makes the interface between human and machine ; the programme of host computer and detectors is designed through using blocking design method

    在本設計中,採用高速的dsp處理器,實現了對故障特徵信息的高速採集與處理;採用大功率的功放晶元與變壓器配合的方法,實現了大電流信號的驅動輸出;採用485總線技術,組建了裝置主機與多探測器之間的主從式通訊網路,實現了多干擾條件下裝置主機與多探測器的可靠通訊;設計了差分式多級選頻放大電路,採用磁感應的方法實現了對空間微弱信號的接收;利用fpga技術,實現了控制器與多外設的介面及數字信號的串並轉換;採用了先進的lcd液晶顯示模塊及鍵盤介面晶元,設計了人機信息交互的介面;採用了模塊化的軟體設計方法,開發了裝置主機及探測器的軟體程序。
  8. An automated de - noising algorithm based on the energy of wavelet packet not donoho ' s threshold algorithm is established. a gear feature vibration signal extraction method using the wavelet packet energy is proposed, which can separate gear meshing vibration, noise vibration and gear fault vibration signal from the original gearbox case vibration signal. basis pursuit ( bp ) algorithm is introduced into the filed of mechanical signal de - noising and feature extraction for the first time

    第三章擺脫了donoho的閾值消噪思想,從能量的角度建立了基於小波包的自動消噪演算法;提出基於小波包能量分佈的齒輪故障特徵信號提取方法,可以將齒輪嚙合振動信號、干擾振動信號以及沖擊振動信號從原始齒輪振動信號中分離出來;首次將基追蹤消噪演算法引入到機械信號的消噪與提取上,通過對齒輪信號的消噪,表明了它的有效性,並對影響該方法實際應用效果的因素進行了全面的分析,同時也指出了該方法存在的局限性。
  9. This thesis mainly study the character information of the primary fault, which is at primary loop system of the marine nuclear power plant. the main content of the thesis is the collection of the basic fault ' s character information, then set up a database

    本文主要研究船用核動力裝置一迴路系統主要信息,論文的工作內容是對基本故障特徵信息進行收集整理和比較,然後將其創建成數據庫。
  10. The transient simulation of stator winding inter - turn short circuit fault has been completed successfully based on the multi - loop mathematical model

    基於神經網路技術,提出了以定子負序導納平均值作為故障特徵量的異步電動機定子繞組匝間短路檢測方法。
  11. So it can be used for single - phase fault identifying. this paper discusses the size of the negative current and the method of analyzing it. numeral simulation shows the feasibility of it

    由於負序電流在線路和非線路上具有顯著差異,本文也研究了將負序電流作為故障特徵量的可行性。
  12. It combines feeder automation, and develops the fault identifying principle from one direction to two direction. so it enhances the redundancy of fault information, and improves the reliability of the fault location. we choose the transient zero current prior to others, for it is bigger than others mostly

    本文敘述了饋線系統保護原理,提出了基於饋線自動化系統的幾種單相接地處理方案,討論了這幾種方案下故障特徵量的比較方式,分析了故障特徵量選用的出發點以及配電終端地址命名規則等問題。
  13. According to the time variation and feature extraction difficulty of rotating machinery vibration signals, the rule of choosing wavelet basis function and wavelet denoising soft - thresholding value is proposed after making further research on wavelet transform technique, using for denoising rotating machinery vibration signals the conception of " energy " is proposed, based on the theory that signals energy in all frequency can be affected by faults deeply, to construct feature vectors of rotating machinery vibration signals which can give a convenient disposal way to fault feature extraction and fault intellectual diagnosis

    針對旋轉機械振動信號的非平穩性及難以提取的點,通過對小波變換技術的進一步研究,提出旋轉機械振動信號處理的小波基函數選擇原則及小波包消噪的軟閥值原則。利用小波包變換對旋轉機械振動信號進行消噪處理和提取。並以「能量」為元素,構造旋轉機械振動信號的向量,從而為旋轉機械振動信號的故障特徵提取以及后續的智能診斷提供了一種便捷的處理方法。
  14. The algorithm is also applied in the broken rotor bars detection in squirrel cage induction machines, which is dependent on detecting the twice slip frequency modulation due to the speed or torque in the stator current, and the rotor bar faults can be detected effectively without some preprocessing

    指出可以利用信號的小波脊線來提取頻率隨時間連續變換的信號的瞬時頻率,並將該瞬時頻率提取演算法成功地應用到異步電動機定子起動電流信號的分析中,有效地提取出了轉子斷條故障特徵
  15. Based on two fault diagnosis instrument systems for rolling bearing and car, several diagnosis strategies using integrated intelligence have been brought forward. applied methods that fault feature is extracted from high frequency resonance signal have also been presented. many experiment results have shown the effectiveness of these methods

    以滾動軸承和車輛診斷儀器系統為研究背景,提出了幾種集成智能診斷策略和從高頻共振信號中提取故障特徵的實用方法,並充分利用這些方法對滾動軸承和車輛的多種診斷進行了實驗研究,證明了這些診斷方法的有效性。
  16. From wavelet analysis, the fault feature of high speed wire rod processer in the heavy section mill of wisco is successfully extracted and from this effective method the same kind accident can be avoided and the fault situation can be confirmed for the future

    成功的通過小波分析提取出武鋼大型廠高速線材軋機齒輪箱輸出接手螺栓拉斷故障特徵,捕捉到信息,為今後判斷、預防同類事及事後確定部位提供了有效的分析手段。
  17. To conquer the problem of acquisition high effectiveness in analog circuit fault imformation, wavelet transform was researched in this paper to preprocess the fault signals. meanwhile, bp neural network diagnosis method based on wavelet transformation was proposed, this method can abstract fault feature effectively and decreases the dimension of imput vector. by this mean, the construct of neural network can be simplified and training time was economized, then the recognize ability of fault type was improved also

    為解決模擬電路的信息高效獲取難題,本文採用小波變換作為信號的預處理器,研究了基於小波變換預處理的bp網路診斷方法,該法能在有效提取故障特徵的同時,降低輸入信息的維數,從而進一步簡化了神經網路的結構,減少了其訓練時間,提高了辨識類別的能力。
  18. And the wavelet packet united with statistic analysis is used to show the fault characteristics intuitionisticly

    同時研究中利用小波頻帶分析技術,使故障特徵顯示更直觀。
  19. In the first session a vibration test and off - line processing scheme is presented according to present on - line testing environments. after the data has been collected, attempt of wavelet transform is made combined with traditional fourier analysis. various methods of wavelet transform are tried to reveal the relations in transform figures

    首先設計出在線測試和離線處理試驗方案,進行振動試驗數據採集,對試驗獲得的數據進行小波分析,將信號進行不同尺度的分解,分析小波變換圖中的規律,提取故障特徵,並對進行診斷。
  20. The paper propose the complex value u - d factorization based least square method to improve the numerical stability and the fault feature are obtained. 7

    為了提高數值計算穩定性,進一步提出了基於復u - d分解的最小二乘參數估計方法,獲得了變頻調速系統的故障特徵
分享友人