數據求精 的英文怎麼說

中文拼音 [shǔjùqiújīng]
數據求精 英文
data refinement
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 據 : 據Ⅰ動詞1 （占據） occupy; seize 2 （憑借; 依靠） rely on; depend on Ⅱ介詞（按照; 依據） according...
  • 求 : Ⅰ動詞1 （請求; 要求） ask; beg; request; entreat; beseech : 求人幫忙 ask sb a favour; ask a favou...
  • 精 : Ⅰ形容詞1 （經過提煉或挑選的） refined; picked; choice 2 （完美;最好） perfect; excellent 3 （細）...
  • 數據 : data; record; information
  1. As to the critical technological problems of the interlock control of three - car coke oven - oven number identification, accurate contraposition and data transmission, the author proposes solutions respectively - rfid, three - light positioning device, coke oven controller and radio transmission network. these solutions can ensure accurate identification of the oven number. for example, the deviation of the automatic parking position is within 10mm

    針對三車聯鎖控制環節的關鍵技術：爐號識別、精確對正和數據通信，本系統採用了射頻識別（ rfid ）裝置、三燈位置檢測裝置、焦車控制器、無線通訊網路等解決方案，可實現無差錯的爐號識別，自動停車定位誤差在10mm以下，通信數據可靠等系統要求。
  2. In the self - calibration scheme, the thesis emphasizes the accuracy of camera intrinsic and extrinsic parameters. we presents an accurate f method based on corresponding point adjustment. the method adjusts coresponding points according to the fixedness of projective transformed cross ratio, then calculates f matrix accurately through linear and non - linear methods. when computing intrinsic parameter, a matrix, we simplify the step, and stress on the two important parameters of a. the result will be getten through solving kruppa equation based on svd decomposition. in order to compute extrinsic parameters, we use linear method to get initial r and t, then apply non - linear method to accurate them

    提出了基於匹配點調整的f求精方法，先根據攝影交比不見性對手工選擇的匹配點進行調整，再用線性、非線性結合的方法求精f矩陣；在計算內部參數a中，進行了一定的簡化，把重心放在a中重要的兩個參數上，用svd分解法計算kruppa方程；在計算外部參數時，首先用線性法求解r 、 t ，然後再用非線性法迭代求精。
  3. In any case, each jurisdiction treats insanity claims in its own way, so they may well disagree over whether brain - image data are exculpatory

    無論如何，每個對待精神錯亂權限的要求，用它自己的方法，因為他們也許在大腦成像數據是辯解無罪上有著一些不一致。
  4. The second, the main work in the paper is discussed. they are include : the theory and character of electromagnetic leaking from a computer ; the theory of accumulation mean filter and pectination filter ; the analysis of synchronous signal precision, at 10 - 12 second level, for stably intercepting ; the technology requirement of receiver and data acquisition board for clearly displaying the images recovered from the intercepted data

    本文從計算機視頻電磁泄漏和數字濾波器兩方面的基本理論出發，詳細論述了計算機視頻信息電磁泄漏的原理及特點，指出視頻泄漏信息的頻譜是以行頻為周期的譜線；分析了重加濾波器和梳狀濾波器的性能；分析了視頻泄漏信息截獲的條件；推導出穩定截獲視頻泄漏信息需要對同步信號的精度控制在皮秒級；論述了清晰再現對接收機和數據採集卡的技術要求。
  5. Considering the precision and cost of sea - route in our country, gps oem board was selected positioning for system in stand - alone model ( not dgps ). there is abundant time to processing and optimizing data for gps receiver because the reactive speed of pharos is on hour level contrast to strict real time

    根據航道定位精度要求與成本承受能力，系統選取低成本的gpsoem板接收機進行單機定位，由於航標燈監控有一定實時性但又非嚴格意義上的實時性，其反應速度可到小時級，這為gps接收機定位提供了寬裕的時間作為數據處理與優化。
  6. The effect of reynolds number on rudder hydrodynamic performance is also analyzed. up to the stall angle the computed lift and drag agree well with measurements and other author ' s calculations, whereas stall angle, lift and drag beyond the stall angle are slightly under - predicted. the solver is used to investigate laminar and turbulent separated flows around a 6 : 1 prolate spheroid at high incidence angles and their effects on hydrodynamic forces

    應用所開發的求解器，以naca0015翼型舵為算例計算了船舵在不同雷諾武漢理三;大學博士學位論文數下大舵角范圍內的三維粘性流場及水動力，成功地預報了舵的失速角和最大升力，並初步探討了雷諾數對舵水動力的影響;計算結果與現有試驗和計算數據比較，吻合程度相當好，初步檢驗和驗證了該求解器精確模擬粘性流動和計算水動力的能力。
  7. On the basis of experimental research, this thesis applies 2 - dimensional non - linear finite element method to the analysis of transient temperature field on the section by means of relatively high precision triangular element of six joints. when the temperature field is analyzed, finite element reseaus are divided in space field and finite difference reseaus are divided in time field, and then the program is compiled. the computing results are in good agreement with the test data

    在試驗研究的基礎上，本文採用精度較高的三角形六結點單元對構件截面二維非線性瞬態溫度場進行了有限元分析，即在空間域內採用有限元網格劃分，在時間域內採用有限差分網格劃分，據此編制了計算程序，計算結果與試驗數據符合較好，程序穩定性好，精度滿足要求。
  8. Since 1980s, non - seismic geophysical instrumentation has achieved great progress in its acquisition accuracy, gathering styles and diversification of parameters, which provides new approaches for petroleum exploration in the newly developed area of western china and southern marine carbonate area, and also makes higher demands on data processing and inter pretation

    摘要20世紀80年代以來，非地震地球物理勘探儀器有了長足的進步，採集精度的提高，採集手段與參數的多樣化，為我國西部新區和南方海相碳酸鹽巖地區的油氣勘探提供了新的方法和途徑，同時對數據處理與解釋也提出了更高的要求。
  9. This thesis introduces the working principle, craftwork requirement, modeling process, control strategies and the realization of lf refining furnance bottom blowing argon control system. through the study and analysis of bottom blowing argon process control system, the thesis discusses the mean neural network model of controlled object and the mathematical models of the exectors, pwm adjustable pressure controller and pcm adjustable flux controller according to the relevant liquid knowledge and relevant data, including design data, test data and running data. to begin with the craftwork reguirement of bottom blowing argon and the actual instance of the control system, it presents the strategies of fuzzy parameters self - adaptive pid control used in pressure difference inner loop and fuzzy plus pi compound control used in flux outer loop which are based on the above modeling in order to carry out the accurate control of argon flux

    本文介紹了lf精煉爐底吹氬過程式控制制系統的工作原理、工藝要求、建模過程、控制策略以及控制系統的實現。通過對精煉爐底吹氬過程式控制制系統進行研究與分析，並根據流體力學的有關知識以及有關數據（其中包括設計數據、試驗數據和運行數據） ，建立起了被控對象的平均神經網路模型和執行機構（即pwm調壓器和pcm調流器）的數學模型。在此模型的基礎上，從底吹氬工藝要求和控制系統的實際情況出發，提出了壓差內環模糊參數自適應pid控制策略和流量外環模糊pi復合控制策略，以實現氬氣流量的精確控制。
  10. Finally, the paper introduces the test of wave simulation by wave - making system that has improved. the test data indicate that it is able to competent at wave simulation of sea wave spectrum for shipmodel test, we have changed the situation that the wave - making system ca n ' t simulated sea waves. and have established the foundation for the quality of improving the scientific research of our school and experiment teaching further

    最後，本文介紹了對改造后的造波系統進行波浪模擬測試情況，試驗數據表明，該造波機經過升級改造，完全可以勝任對船模耐波性試驗所要求的海浪譜的模擬，並且還可以根據需要模擬任意的海浪譜，模擬精度達到試驗要求。
  11. The numerical simulation equations of the border curves in term of and as well as the matching rules and the frequency dependence of microwave electromagnetic parameters of a broad - band homogeneous absorbing coating with a finite value of reflection loss are available. these results pointed out the direction to develop rams ". according to the radar - absorbing model, the optimized design of rams with thin - layer, light - weight, broadband and strong - absorbing is available by the simple genetic algorithms, which can effectively conduct the research work of rams to the detail. small but completely, the electromagnetic parameter ' s databases of rams that based on actual microwave absorbers have been set up, the object function has been constructed which conform to the involved goals, the adaptive coding measure is taken which extends the coding length dynamically adapting to the condition of the number of actual absorbers or the precision of thickness and absorber - volume - percentage, the decoding technique is initiated which satisfies light - weight and strong - absorbing as well as thin - layer and broadband by adopting of tracing variable restricting conditions dynamically to control total thickness. when decoding, the variable restricting conditions of thickness are dynamically traced, so gain the radar absorbing coatings of light - weight multiple - layer single - ingredient. similary, of thickness and absorber - volume - percentage, of light - weight multiple - layer multiple - ingredient. also, the rams ' demand to radar - absorb performance as frequency is met making use of the penalty function

    作為遺傳演算法的具體實施：根據本實驗室近來研製的吸波材料，建立了吸波材料的相關數據庫；構造了能真實體現「薄、輕、寬、強」優化目標的目標函數；根據材料的實際數量以及塗層厚度精度要求、吸收劑體積分數精度要求，建立了能動態擴展相應碼長的自適應編碼方法；首創了通過動態跟蹤變量的約束條件來控制塗層總厚度的解碼技術，以此實現了在不弱化寬頻、高強的吸波性能目標的同時，兼顧到薄層、輕質的使用性能要求；在解碼時通過動態跟蹤厚度變量的約束條件，實現了多層單組分吸波塗層對重量輕的要求；通過動態跟蹤厚度變量的約束條件和吸收劑體積分數的約束條件，實現了多層多組分吸波塗層對重量輕的要求；使用權重系數變化法，實現了吸波塗層的分頻段吸波性能要求。
  12. It will improve analysis efficiency and experimental precision greatly if putting the photoelastic images gotten from experiment into computer, obtaining the isochromatic and isoclinic data automatically and writing it into database directly. but because of the limitation of time and the difficulty of drawing pure isoclinics from images, the paper has only shown the achievements presently and simulated a disk under diametral compression as foundation on further research

    把實驗中拍攝到的光彈性圖像輸入到計算機中，利用自動處理系統獲得等色線和等傾線等原始數據並將其直接輸入數據庫中，再依據本文提供的原理和方法求解結構的彈塑性應力值，可以大大的提高分析效率和實驗精度。
  13. But it is difficult to read data. the most discommodiousness is that the data read ca n ' t be saved and dealed with

    精度尚可，能達到要求但讀數困難，也不能進行數據的保存和后處理。
  14. I can tell that it is an area filled with sophistication and intelligence, but somehow both the polish prefix notation and endless parentheses, and the fervent semantic eschewal of a distinction between code and data, continue to feel alien to me

    我可以告訴您這是一個充滿精巧和智慧的領域，但不知何故，無論是波蘭表示法（前綴表示法）和無休無止的括號，還是規避代碼和數據之間語義差別的熱切追求，仍然令我感到陌生。
  15. In this thesis, based on activity based classification, there are three subjects to be researched, that is, how to build and express cost caculation rules, how to support many caculation methods and how to support more quick and accurate cost caculation. moreover, this thesis lucubrates a flexible cost cacaulation model. this model bases on advanced cost theory - - activity based classification, and it includes the building of abc ' s cost caculation model, the receptions " automatical accumulattion and transformation rules, the storage and use motivating causes rules, the diverse cost distribution and supporting many cost caculation methods. besides, the model brings forward rules about cost information transformation and accumulattion, rules about keeping business records, rules about motivating causes ’ accumulattion, rules about cost distribution and formula language. what ’ s more, it builds a rule engine, and all of these make this model meet enterprises ’ demand for using many cost caculation methods, and then simplify operators ’ operation. also, it can realize cost accumulated more accuratly, keeping business records more promptly and cost analysed more intensively, and then give supports to enterprises ’ further decision with related data. in the third chapter, it expounds the design and realization of this flexible cost cacaulation management system, and use one model case to validate its legitimacy, which explains that with j2ee technology and mvc design pattern, this system has good features of reuse and adaptability. at last, it introduces its application in china resource alcohol co., ltd

    本文以作業成本法為理論基點，圍繞著如何建立成本核算規則並給予表達、如何支持多種成本核算方法以及如何提供更為快捷、精確的成本核算等三大主題展開深入的研究，並建立了多適應性成本核算模型。該模型以先進的成本核算方法作業成本法為理論基礎，涵蓋了從作業成本核算模型的建立到成本單據自動歸集轉換等規則的提取，從動因量存儲使用等規則的建立到成本多樣化分配以及支持多種成本計算方法等全部內容。在對成本核算規則進行分析和表達的基礎上，該模型提出了基於作業成本法的成本信息轉換存儲規則、記賬規則、動因量歸集規則、分配規則以及計算公式語言，並建立了基於這些規則的規則引擎，從而使得該模型能夠滿足企業多種成本計算方法的需求，簡化了企業人員的操作過程，並且實現了更為準確的成本歸集，更為迅速的成本制單，以及更為細化的成本分析，為企業的進一步決策提供了有力的數據支持。
  16. In addition, the paper designs a bottom database model, selects a multi - aim strategy combining files with known data, and establishes dual interaction data model that has explicit conceptual structure and directly aims to geographic objects, and provides backing up enquiry language ( g - sql ). simultaneously, after analyzing and studying methods available for the under pipelines, the paper constructs survey adjustment calculation model, and according to the model, checks the survey of under pipelines. the results indicate that the model is suitable to actual requirement because it greatly increase calculation speed, meeting calculation accuracy requirement

    在此基礎上，對系統的底層數據模型進行設計，選擇了文件與成熟數據庫相結合的混合策略，併兼顧面向對象的數據庫（ oodb ）和可擴充數據庫（ edb ）的特點，建立了一個概念層次清晰、面向地理對象實體的雙層語義數據模型以及支持模型的查詢語言g - sql ，同時對地下管線的各種測試方法進行分析研究，建立了地下管線測量平差計算模型，並以此對所勘測的地下管線進行核算，計算結果表明，計算模型不僅大大提高了核算的速度，同時在計算精度上也符合核算的要求，是符合實際要求的關于測量平差計算的模型。
  17. This paper discussed the coordinate transformation method of wgs84 coordinate system to 1954 - beijing gauss grid coordinate. introduced transformation model of wgs84 to beijing 54 and computing method of transformation parameter. according to different model and computing method, computed and compared with the result combine real data

    本文詳細討論了wgs84大地坐標轉換到北京54坐標系下的高斯平面坐標的方法，重點介紹了wgs84和北京54的空間直角坐標的轉換模型及轉換參數的計算方法，並根據不同的模型和計算方法結合實際數據進行計算和結果的比較，認為採用基線向量求解的四參數模型具有較高的轉換精度，分區變換和提高控制點精度也能提高轉換的精度。
  18. It is discussed that the present harmonic analyzers do n ' t satisfy the requirements of china standard for harmonic measure of quick disturbance harmonic load. the measurement error brought about by the harmonic analyzers adopting ft or fft algorithm is analyzed. a cycle discrete fourier algorithm that should n ' t be effected by aperiodic component is presented, and the results of simulation show that it has higher accureacy

    本文對電力系統諧波的測量方法，數據處理及電力牽引負荷對電力系統的影響進行了研究，論述了目前國內外生產的諧波分析儀用於快速波動諧波負荷的測量不滿足國標的要求，分析了諧波分析儀普遍採用的ft或fft演算法所產生的測量誤差，提出了一種不受非周期分量影響的全周波離散傅里葉演算法，模擬結果表明精度好。
  19. The experimental results show that the effect of ib is much larger than that of the noise on estimating ionospheic delay, and ib can cause ionospheric delay measurements to include systematic errors of the order of several meters. therefore, one must significantly take notice of ib and remove its negative effect, and should not casually consider ib as part of noise whenever gps data are used to fit ionospheric model or to directly calculate ionospheric delay. ( 3 ) stability of ib is studied with a refined method for separating it from ionospheric delay using multi - day gps phase - smoothed code data

    算例表明，新方法通過採用平均去噪分離方法后處理相位丞于g陀的電官唇監剝及延遲改正工論與方法的研究平滑測碼數據，求出儀器偏差並對需要實時處理儀器偏差的觀測數據進行預報改止，直接利用觀測值確定電離層延遲量，待估參數少、能消除儀器偏差的大部分影響，具有較好的精度，可作為waas及其他gps網路系統確定電離層延遲的可行的參考方案。
  20. Occasional requests are received for statistics not readily available from standard tabulations. these are also entertained at a charge subject to the level of analysis permissible having regard to considerations of statistical precision and data confidentiality

    有時候，已編制的標準統計表未必備有使用者要求提供的數據，如遇上這情況，本處會考慮有關統計數據的精確度及個別資料保密規定所容許的分析層次來提供有關資料，並收取所需費用。
分享友人
分享到 Line

分享到臉書