斜交軸 的英文怎麼說
中文拼音 [xiéjiāozhóu]
斜交軸
英文
oblique axis-
The author suggests that the three lithosphere - scale faults, lancangjiang fault, jinshanjiang - ailaoshan fault and axis fault in the middle of the basin, are the main geological structures that control the formation of basin, magmatism and metallogenic congregate district. the anticline structure with an axis of triassic strata and the related fault system within the basin, and gonglang arch - shaped folding structure in the south of the basin are the geological structure controlling the formation of ore fields. junctions of two or more faults with different orientation, interlayer cataclastic structural zone and oxidation - reduction ( redox ) boundary were the favorable position for the formation of ore bodies
認為瀾滄江斷裂、金沙江-哀牢山斷裂及盆地中軸斷裂這三條巖石圈斷裂是主要的控盆-控巖（巖漿巖）構造及礦集區尺度的控礦構造；盆地中以三疊系為軸的背斜構造及相關的斷裂系統、盆地西南緣公郎弧形構造等是礦田尺度的控礦構造；多組斷裂的交叉、層間破碎帶及地層柱中的氧化還原界面是形成礦體的有利部位。All of the hydraulic structures are arranged in the right bank and four underground seepage tunnels are arranged parallel in horizon, and the axle wires intersect with syncline axis almost perpendicularity, and with rock formation obtusely. complex underground tunnels are formed under such formidable conditions, and each of seepage tunnels crosses nuclear of syncline and comes up against interlaminar sharing disturbed belt at different footage
四條引水發電隧洞在平面上平行布置，軸線方向與本區構造線方向近於垂直，與巖層走向大角度相交，構成一復雜地下洞室群，並在不同洞段通過沙金壩向斜核部，且遭遇多條層間剪切錯動帶。Through systemic analyzing on spiral helical gear transmission with different basic parameters, the essay found out rules of how can such basic parameters influence spiral helical gear engagement characteristics. so it brings forward the auxiliary assembling mode of adopting one straight gear and one helical gear on condition of little axial angle as well as treasures to ameliorate ill engagement performance on condition of large axial angle, another two jobs of the essay are to clarify the wrong concept that spiral helical gear can only transmit movement but not impetus and to provide a brief and practical method of analyzing contact for gear pairs whose surface equations can be written out directly
通過對不同基本參數的螺旋齒輪傳動進行系統研究，找出了螺旋齒輪基本參數對其嚙合特性的影響規律，提出小軸交角條件下可採用一直齒輪、一斜齒輪的齒輪副組合方式，給出了大軸交角條件下嚙合性能不良的改進措施。澄清了螺旋齒輪只能傳遞運動不能傳遞動力的誤區，為能夠直接寫出齒面方程的齒輪副進行齒面接觸分析提供了一種簡便、實用的新方法。Abstract : in this paper, the best selection of key parameter helix angle is discussed for all kinds of cross helical gear transmission in order to raise efficiency, reduce wear, obtain lighter weight and less size of bearing
文摘:從提高效率、減少磨損、減輕重量和較小軸承尺寸的角度出發，綜合探討了交錯軸斜齒輪傳動的各種組合中，關鍵參數螺旋角的最佳選擇The results of computer simulation a re proved. thirdly, the paper analyze the angle error caused by elevation axis not in horizontal plane, make a conclusion that 3 - axes perpendicular radar can not track in the whole airspace, propose the structure of slant 3 - axes radar
然後，從工程實際出發，著重分析了俯仰軸不嚴格水平對雷達測角系統造成的誤差，得到了正交三軸雷達並不能進行全空域跟蹤的結論，提出了傾斜三軸的雷達天線座結構形式。It is proved by computer simulation that the slant 3 - axes radar can be used in target tracking in the whole air space without blind zone and beam slant. it is pointed out that the slant 3 - axes radar can reduce the maximum angle for elevation axis compared with 3 - axes perpendicular radar, then reduce the technique demand of angular velocity and acceleration of elevation axis
通過模擬驗證了傾斜三軸雷達系統在工程上可以做到波束無傾斜和全空域跟蹤無盲區的結論，並指出此系統與正交三軸系統相比，可以減少俯仰軸的最大轉動角，從而降低系統對俯仰軸的角速度和角加速度的技術要求。分享友人