斜力 的英文怎麼說

中文拼音 [xiélì]
斜力 英文
inclined force
  • 斜 : 形容詞（跟平面或直線既不平行也不垂直的） oblique; slanting; skew; bevel; diagonal; askew; inclined; tilted
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  1. The thesis has summarized the development of the oblique - pull bridge, its construction technology and the importance of bridge construction control, then has introduced project general situation, and has narrated detailed regulation, organization construction, the major work and difficult part of this bridge construction control. the following is the key part of this thesis, firstly, it has introduced the experiment work of early stage, structural calculation and its theoretical result : the absolute altitude of each operating mode, the absolute altitude of building mould in each section and the absolute altitude after pouring concrete ; then, it has discussed the method and content of the line shape control of the main beam, actual absolute altitude of building mould is put forward, and it has described the method of structural stress monitoring, how to arrange measure point and collect data, and how to analyze data. it has also narrated the method of rope force detection and structural temperature inspection

    本論文在總結了斜拉橋的發展及其施工工藝，並指出了橋梁施工控制的重要性之後，簡要的介紹了工程概況，敘述了炳草崗金沙江大橋監控細則、組織機構及監控的主要工作和難點部分；論文的核心部分，在介紹了炳草崗金沙江大橋施工控制與監測工作的前期實驗工作和施工各工況標高、各節段支模標高、澆注混凝土后的標高的結構計算和其理論計算結果之後，詳細論述了主梁的標高線形控制方法和內容，實際支模標高的提出，結構應力監控的方法、布點、測讀及其對測讀數據的合理分析方法，索力檢測和結構溫度監測的方法。
  2. It is significant that the manufacture of strabismus real time aerial camera could strengthen our national defense

    因此斜視實時航空相機的研製將對增強我國國防實力具有重要意義。
  3. If the velocity of atoms is near to zero, the light for ces will tend to confine the atoms near to nodes and antinodes. the stability depends on the magnitude of the negative slope of the light force, the depth of the potential well and the momentum diffusion coefficient. it is important to select the parameters, e. g

    如果通過激光冷卻能使原子速度降至很小甚至為零，光壓力的作用將使原子被較穩定地囚禁于激光駐波場的節點和反節點處，其穩定程度取決于該處光壓力曲線負斜率的大小、對應勢能的勢阱深度以及動量擴散系數的大小，因此，如何在實驗中合理選擇激光強度、失諧量等顯得尤為關鍵。
  4. The various colours significant of various degrees of vitality white, yellow, crimson, vermilion, cinnabar : their degrees of brilliancy : their magnitudes revealed up to and including the 7th : their positions : the waggoner s star : walsingham way : the chariot of david : the annular cinctures of saturn : the condensation of spiral nebulae into suns : the interdependent gyrations of double suns : the independent synchronous discoveries of galileo, simon marius, piazzi, le verrier, herschel, galle : the systematisations attempted by bode and kepler of cubes of distances and squares of times of revolution : the almost infinite compressibility of hirsute comets and their vast elliptical egressive and reentrant orbits from perihelion to aphelion : the sidereal origin of meteoric stones : the libyan floods on mars about the period of the birth of the younger astroscopist : the annual recurrence of meteoric showers about the period of the feast of s. lawrence martyr, 10 august : the monthly recurrence known as the new moon with the old moon in her arms : the posited influence of celestial on human bodies : the appearance of a star 1st magnitude of exceeding brilliancy dominating by night and day a new luminous sun generated by the collision and amalgamation in incandescence of two nonluminous exsuns about the period of the birth of william shakespeare over delta in the recumbent neversetting constellation of cassiopeia and of a star 2nd magnitude of similar origin but lesser brilliancy which had appeared in and disappeared from the constellation of the corona septentrionalis about the period of the birth of leopold bloom and of other stars of presumably similar origin which had effectively or presumably appeared in and disappeared from the constellation of andromeda about the period of the birth of stephen dedalus, and in and from the constellation of auriga some years after the birth and death of rudolph bloom, junior, and in and from other constellations some years before or after the birth or death of other persons : the attendant phenomena of eclipses, solar and lunar, from immersion to emersion, abatement of wind, transit of shadow, taciturnity of winged creatures, emergence of nocturnal or crepuscular animals, persistence of infernal light, obscurity of terrestrial waters, pallor of human beings

    顯示出不同程度之生命力的繽紛色彩白淺黃深紅朱紅銀朱諸星之亮度一直包括到七等星以等級標志的諸星之大小諸星的位置御夫座沃爾辛厄姆路172大衛的戰車173土星光環螺旋星雲凝固后形成有衛星的恆星群兩重大陽相互依存的旋轉運動伽利略西蒙馬里烏斯174皮亞175勒威耶赫歇耳加勒176等人各自獨立地同時所做的發現波得和開普勒所嘗試的距離的立方與回轉次數的平方的體系化177多毛的眾彗星178那幾殆無限的被壓縮性，以及自近日點至遠日點那廣漠的遠心的重返大氣層的橢圓軌道隕石的恆星之起源年紀較輕的天體觀測者誕生的那個時期火星上所出現的「暗波」現象179每年在聖勞倫斯節殉教者，八月十日前後降落的隕石雨每月都發生的所謂「新月抱舊月」現象180關于天體對人體的影響的假定威廉莎士比亞出生的時期，在斜倚卻永不沒落的仙后座那三角形上端，一顆不分晝夜散發著極亮光彩的星辰一等星出現了181這是兩個無光死滅了的太陽因相撞並汞合為白熱體而形成的燦爛的新太陽大約在利奧波德布盧姆出生時，出現在七星花冠星座里而後又消失了的一顆同一起源亮度卻稍遜的星宿二等星182還有約於斯蒂芬迪達勒斯出生時，出現在仙女座中之後又消失，小魯道爾夫布盧姆出生與夭折數年後出現于御夫座后又消失，以及另外一些人出生或去世前前後後出現在許許多多其他星座中而又消失了的假定是同一起源的實際存在或假定存在的星斗183 。
  5. Perfect pre - processing and post - processing function is one of the main factors to evaluate the vitality and market value of the finite element analysis system surveying today development of finite element analysis technology, most of which concentrate on establishing fine user interface, also has some limitation on application, and especially, the research on the visualization of arbitrary cut - plane is always in ascendants to realize the visual processing on cut - plane needs reprocessing the results of finite element analysis which have get, so the algorithm is two parts : seeking the physical value of cut - plane and drawing 2d contours, the former, based on the theory of stress on " arbitrary inclined plane " in physical mechanics, use the method of linear interpolation method to get the coordination and physical value of intersection between cut - plane and element arris ; the latter, based on the tables on elements, nodes, stress and strain, summarize a rapid algorithm of generating 2d contours based on the grid. this thesis synthesizes there two parts and get a visual processing program under fortran

    縱觀有限元分析技術的發展，目前大多集中在建立良好的用戶界面上的研究仍存在許多應用上的局限性，其中對任意剖面上可視化的研究仍處于方興未艾的階段。要實現任意剖面上可視化處理，必須先將得到的有限元計算結果進行再處理，因此在演算法上分為兩部分：求任意剖面上物理量值的演算法及二維等值線演算法。前一部分以彈性力學中「任意斜截面的應力」為理論基礎，利用線性插值方法得到截面與單元棱邊的交點坐標及交點物理量值；在此基礎上；根據已得到的單元及節點序號表、應力應變物理量表，總結出一種基於有限元剖分網格的快速生成二維等值線的演算法。
  6. I, too, in the grey, small, antique structure, with its low roof, its latticed casements, its mouldering walls, its avenue of aged firs - all grown aslant under the stress of mountain winds ; its garden, dark with yew and holly - and where no flowers but of the hardiest species would bloom - found a charm both potent and permanent

    她們喜歡這個與世隔絕的家，我也在灰色古老小巧的建築中找到了巨大而永久的魅力。這里有低矮的屋頂帶格子的窗戶消蝕的小徑和古杉夾道的大路強勁的山風使這些古杉都已傾斜。還有長著紫杉和冬青而呈黑色的花園一這里除了頑強的花種，什麼花都不開放。
  7. Based on the analysis of mechanism for joint region, the " frame - wall " and " aslope compression stub column " mechanical models and yielding patterns of core zone of the joints are set up. the shear load - carrying formulation for joint core zone is also given in terms of plastic ultimate analysis. and then, the comparisons between the formulas given in this paper and that of chinese design code ( draft ) and nonlinear fem as well are presented

    對節點核心區的抗剪，通過受力機理的分析，建立了鋼「框架剪力墻」加混凝土「斜壓短受力體系及其屈服機制，根據塑性極限分析，給出了節點核心區抗剪承載力計算的迭加公式， 《規程》公式和非線性有限元近似模擬分析結果進行了比較。
  8. From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints

    採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。
  9. Theoretical computation of the barometric pressure effects on deformation, gravity and tilt

    重力和傾斜觀測影響的理論計算
  10. In chapter 3, we briefly present the fundamental theory of the elastic response of a spherical earth to the surface loads and the treatment to the loading effects of the barometric pressure

    第三章：簡述球形彈性地球負荷響應解的基礎理論和大氣負荷效應的處理方法；建立大氣重力和傾斜格林函數表達式
  11. Stability of rock slopes is generally controlled by the structure of rock masses, especially the soft structure surfaces. analysis of rock mass structures is a key to establish geological models and numerical simulation and a foundation to assess the stability of rock slopes. the weak structure surfaces are mainly bedding planes, faults, joints, schistosity plane and contact zones of intrusive bodies. since they are different in genesis and scale, the rock masses are different in features and mechanical intensities. based on the combination of rock structure bodies, 15 basic modes of deformation and failure of rock slope are systematically summarized. the deformation and failure of rock masses actually result from the recombination and rearrangement of these rock bodies. there are 11 types of rock mass structures and various deformation and failure of bank slopes are present in the reservoir area of the three gorge project

    巖體結構，特別是軟弱結構面對基巖斜坡變形與破壞具有顯著的控製作用，巖體結構模式分析是建立斜坡地質模型和數學模型的關鍵和評價斜坡穩定性的基礎。巖層層面斷裂構造節理裂隙片理與劈理以及侵入體和圍巖的接觸帶等是控制基巖斜坡穩定的軟弱結構面，這些成因不同大小不一的結構面將巖體分割成性質各異力學強度不均的各種巖體結構體，構成了15種基巖斜坡變形破壞的巖體結構基本模式。不同結構體的重新組合與排列是斜坡失穩的內在原因。
  12. The fault controlled the magmatism and metallization relevant to the contact zone, and deformed successively and produced cataclastic rocks and two sets of joints ; the second stage was from late cretaceous to eocene. the fault zone deformed right - laterally under ne - sw striking transtention, and new joints zone was produced at the end of the two main faults because of local stress concentration. the fault produced inchoative cataclastic rocks, and two sets of typical joints in plutons ; the third stage of deformation was relatively faint and only a little of microcracks was produced and infilled with vei ns in the deformed rocks, which was during the himalayan movement

    其後的繼承性活動在斷裂帶內形成碎裂程度最強達到碎裂巖的碎裂巖系列構造巖，變形帶兩側發育兩組典型的共軛剪節理；第二次在晚白堊世?始新世，斷裂在北東?南西向近水平擠壓作用下右行張扭性活動，斷裂帶兩主斷裂在斜列重疊的端部由於局部應力集中進一步擴展形成節理帶，而斷裂在巖體區也發育兩組典型的共軛剪節理，斷裂內形成初碎裂巖為主的構造巖；第三次是喜山期以西側抬升、東側下降的強烈升降為主的活動，在基巖中，主斷層兩側圍巖出現微破裂。
  13. The following are the large projects undertaking by haifeng company : crude oil electricity plant project of north china oil field hydroelectricity factory, apartment ( 22 stories ) of yuanda real estate company of dalian shipping group, helios hotel of helios group in dalian development zone, tilt aqueduct bridge of shanxi hongqi reservoir ( total span : 267m ), supply and sale building and city construction building ( both are antique architectures ) of shanxi heyang city, sea drainage pipe of hainan fudao fertilizer factory ( 1520 ), 8 oilgas docks of hainan haiyan oilgas company, basha condensable gas transfer station of haiyan company, 10, 000m3 oilgas storage tank of arco company ( usa ) in hainan nanshan, gas pipe and fuel gas installation project of hainan nanshan electricity co., ltd, base and accessory project of hainan gas company, bei da huang cereal and oil market in harerbin, hainan cross island pipe, changhuajiang river pipe crossing project, taihangshan mountain earthwork project ( the 19th section of west - to - east gas transmission project )

    海南海峰公司承建大的工程項目：華北油田水電廠原油發電站工程；大連船泊集團遠達地產公司的遠達公寓（ 22層） ；大連開發區香港太陽神集團的太陽神大酒店；陜西紅旗水庫斜拉渡槽工程（全跨267m ） ；陜西合陽供銷大樓及城建大樓（均為仿古） ；海南富島化肥廠排海管線（ 1520 ） ；海南海燕油氣公司八所油氣碼頭；海燕公司白沙液化氣中轉站；海南南山美國阿科公司儲油氣萬立米大罐工程；海南南山電力股份有限公司天然氣管線及燃氣安裝工程；海南南海天然氣有限公司基地及配套工程；哈爾濱北大荒糧油批發市場；海南環島管線；昌化江穿越工程；西氣東輸十九標段，太行山土石方工程。
  14. The corbel ' s dimension should be ascertained as the manipulative condition of diagonal section. the amount of longitudinal reinforcement be ascertained on the basis of the flexure model, is obtained according to static for balance condition, the calculative expression of the load is obtained. and in terms of the design method in ultimate state the maximum load

    我國規范對于牛腿的設計規定，牛腿尺寸的確定以斜截面抗裂作為控制條件，縱筋用量的確定以彎壓破壞模型為基礎，根據靜力平衡條件得到承載力的計算公式，按照極限狀態設計方法計算得到，箍筋用量則按照構造要求確定。
  15. It canbe determined the enhancing effect of new steel fiber to shear resistance of beams by the test of tensile strength of steel fiber reinforced concrete, it is important to reduce test cose and increase research efficiency

    可以通過鋼纖維混凝土抗拉強度試驗來確定新品種鋼纖維對梁斜截面上混凝土受剪承載力的增強作用，這對于降低試驗成本和提高研究效率具有重要工程價值。
  16. The croup slopes away from the spine at an angle, but never so steeply as to restrict the rearward thrust of the hind legs

    臀部的斜面遠離脊骨處，呈一定的角度，但是不要感覺看上去的角度很明顯，以免影響後腿的后蹬力。
  17. The main production includes heat - pipe, heat - pipe exchanger setting, rubber tyre hot water deaerate power station, boiler deaerator, tyre forming machine, rubber cutting machine, vulcanize, vulcanizing pot and the special carbon steel or stainless steel pot for oil, chemical engineering, medicine, chemical fertilizer field use

    濟南仙峰泰山化工設備有限公司主要生產熱管、熱管換熱器、橡膠輪胎廠子午胎斜交胎熱水除氧動力站、鍋爐除氧器、輪胎成型機、切膠機、硫化機、硫化罐，還有石油、化工、化肥、醫藥、冶金、建材等行業使用的各種碳鋼、不銹鋼、有色金屬的塔、罐、釜、換熱器等產品。
  18. Drilling track is key factor which decide trenchless success or failure, but controlling drilling track stay around rectifyed phase at the present. guided the theory of force is the key affectting the drilling track, the paper discuss primary factors on contralling drilling track, and advance the formulary ahout reckoning deviation force and azimuth force, expect to achieve the aim that drilling track were controled real time and be anticipated, and have the initiative on drilling track contaolling

    巖層鉆進軌跡是決定非開挖成敗的關鍵因素，目前對鉆孔軌跡的控制僅僅停留在被打糾偏層面上，本文在力是影響鉆進軌跡本質因素理論指導下，對影響巖層鉆進軌跡控制的因素進行了理論探討，並針對造斜力和變方位力提出了計算模式，希望最終能實現鉆孔軌跡的實時監控與調整，變被打糾偏為主動鉆進。
  19. For example ; the inclined government policy, the peasants " idea renovation for the ecology protection, meliorating the country economy arrangement as the local condition, strictly restraining the population and bettering the people ' s quality, establishing the modern agricultural technique system, setting up more towns for the redundant labor transfer

    如加大政策傾斜力度；進一步更新觀念，提高農民的環境保護意識；調整農業產業結構；嚴格控制人口數量，提高人力資源素質；建立現代農業技術體系；發展小城鎮，轉移農村剩餘勞動力。
  20. Bit inclination force

    鉆頭偏斜力
分享友人
分享到 Line

分享到臉書