斜彎道 的英文怎麼說
中文拼音 [xiéwāndào]
斜彎道
英文
ramp-
As one kind of key equipment in piping work of large - scale turbo - generator set in power plant, the machine is especially applicable to various welding bevels, flat end and angle of outer & inner diameter of ascending pipe, elbow pipe, bend, flange and etc., which greatly meets demands in pipe processing of construction site and manufacturers
本機床是電站大型汽輪發電機組的管道施工的關鍵設備,對直管、彎管、彎頭、法蘭等管體的各種型式焊接坡口,端平面,內外徑過緩斜度及直口,能滿足施工現場和製造廠家對各種管件的加工要求。Under the all different structures " combination, the water surface had large bias and turn - around in the torturous path, and in the middle of the path along the longitude, there had the regularity that sink bank surface was higher than the convex bank one
在所有結構組合條件下,彎道水面都有較大偏斜和扭曲,並且在彎道中部主法線方向上,基本為凹岸水面高凸岸水面低的規律。Because the intervals of two side girders are relatively large in the structure of the floor, it is not even and some and out of shape that its bridge of panels must be produced at the same time horizontally and crookedly and vertically except deforming wholly, level analyse can receive the satisfied result already at this moment, is it is it accord with floor structure real work state, girder of cable - stay bridge just to analyse with whole out of shape relevant non - linear space of function while being out of shape while being above - mentioned to consider only, but about this research rarely seen to report bridge worker is it understand their receive strength characteristic in an all - round way to need badly publicly
由於肋板結構中兩個邊主梁的間距較大,其橋面板除整體受力變形外必然同時產生橫向彎曲和縱向不均勻局部變形,此時平面分析已不能得到滿意的結果,只有考慮上述變形與整體變形相關作用的非線性空間分析才符合肋板結構主梁斜拉橋的實際工作狀況,但有關這方面的研究鮮見公開報道,橋梁工作者急需全面了解其受力特性。The structure of this machine is designed as asymmetrical 3 - roller structure form. this machine has the two functoins ; prdbending and circlerolling and is widely used in decoration, chemical industry, metal structure, raceway and oil pipe line, machine manufacture and other trades. the upper roller and lower roller are the driving ones and side roller is the driven one, the lower one lifts vertically and the side one moves slantingly. this machine is convenient in operation and maintenance. so it ~ sreally an ideal epuipment for bening and modilling the thin plates
本機械結構型式為三輥非對稱式,他具備預彎和卷圓兩種功能,廣泛應用與裝潢、化工、金屬結構、輸水輸油管道及機械製造行業,本機種上下輥為主動輥,側輥為從動輥,下輥垂直升降,側輥傾斜移動,操作維修方便,是金屬薄板彎曲成型的理想設備。If the satellite has a tilted orbit, the result is a series of vertical bending waves, an out - of - plane corrugation ? small ripples in a cosmic carpet
如果衛星的軌道是傾斜的,就會有一連串垂直的彎曲波,也就是突出平面的皺紋,好似宇宙地毯的漣漪。Unlike tsuen wan and sha tin, tuen mun was nearly 25 km from kowloon and most of the existing road connection was a tortuous 2 - lane road on the coast which, because it was planned in the days before fast motor traffic, twisted in and out as it followed the coast to minimize cutting and filling slopes
屯門距離九約25公里,在兩者間興建連接道路時,情況與沙田及荃灣有所不同。原有的青山公路只有兩條行車線,設計時車輛沒有像今日般快速,為了減少削填斜坡,它是沿著彎曲的海岸線而建。The roads cannot be on an incline, have a sharp bend or sharp turning movement, or exceed 18 500 vehicles per day of which less than 35 per cent could be commercial vehicles
這些道路必須符合多項要求,包括不能有斜坡彎位或急彎,每日行車量不可超過18 500架次商用車輛必須為35 %以下。6 ) the contrast between different heights of the ridge. through contrasting the researches in the system, the author had found that within the above influence factors, the corner was the most important one. above all, the influence with combination of big corner, large bottom and sluice c
經過比較系統的研究發現,上述諸多影響彎道水流特性因素中,轉角具有最主要的作用,尤其大轉角與較大底坡和泄量組合后的綜合影響,會使水面偏斜和螺旋流變化更為明顯,也更加不規則。分享友人