斜接焊接 的英文怎麼說
中文拼音 [xiéjiēhànjiē]
斜接焊接
英文
mitre welding- 斜 : 形容詞(跟平面或直線既不平行也不垂直的) oblique; slanting; skew; bevel; diagonal; askew; inclined; tilted
- 接 : Ⅰ動詞1 (靠近;接觸) come into contact with; come close to 2 (連接; 使連接) connect; join; put ...
- 焊 : 動詞(用熔化的金屬修補金屬器物或使金屬工件連接起來) weld; solder
- 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
-
As one kind of key equipment in piping work of large - scale turbo - generator set in power plant, the machine is especially applicable to various welding bevels, flat end and angle of outer & inner diameter of ascending pipe, elbow pipe, bend, flange and etc., which greatly meets demands in pipe processing of construction site and manufacturers
本機床是電站大型汽輪發電機組的管道施工的關鍵設備,對直管、彎管、彎頭、法蘭等管體的各種型式焊接坡口,端平面,內外徑過緩斜度及直口,能滿足施工現場和製造廠家對各種管件的加工要求。During the course of the manufacture for packaging 2000 pixel hgcdte irfpa wafer, some crucial techniques are solved, such as the design of the button stem structures with inclined dragging wires applied in cryogenic platform, the optimization of long linear irfpa detector ' s signal wires layouts, the implement of a fanout board having thin film gold metalization for defining the required electrical conductors and a method of hermetically sealed vacuum enclosure of large dimension windows, etc
在用於封裝2000元碲鎘汞焦平面晶元的分置式微型杜瓦研製中,詳細闡明了一種焦平面晶元其裝載面為斜拉式支撐結構的設計,實現了探測器外引功能線的布線優化及其輸出引線工藝改進,並提出了一種大尺寸高氣密光學窗口的焊接方法等關鍵技術。Welding position defined by means of angles of slope and rotation
用斜角和旋轉角定義的焊接位置This ship is built of aluminum alloy all - welded mono - hull, knuckle lines, single bottom, single deck, single engine, single propeller, single rudder, transom stern, raked stem and raked keel, deployed to transport passengers on class iii navigational area set forth by hongkong marine department
15 . 6m本船為鋁合金焊接單體船,型線為折角線型單底單甲板單機單槳單舵方艉,前傾艏柱傾斜骨,用於香港海事處規定之iii類航區接送旅客。Two main factors contribute to the increase : quantity of shaped steel and the section size of the tilted bar and the quality of weld
影響勁性混凝土柱抗震能力的兩個主要因素為:含鋼率和斜腹桿大小及焊接質量。Based on the analysis of the experiment results, it is regarded that the seismic behavior of the truss src columns is higher than those of rc columns. the steel requirements, the crosswise rod dimension and the welding quantity are the main factor, which influence on the truss type src columns
通過對試驗結果的分析,認為配置角鋼桁架式空腹鋼骨的鋼骨混凝土柱的抗震能力明顯高於鋼筋混凝土柱,配鋼率和斜腹桿的大小與焊接質量是影響桁架式空腹鋼骨的鋼骨混凝土柱的主要因素。Control and reduce the deformation of welding for frame of ball nodal in such kind of steel tube as diagonal laying of quardcone and quaraune diagonal laying with double phase
兩向正交斜放類型鋼管球節點網架焊接變形的方法The metal membrane soldered directly to the pressure union converts pressure into a proportional deflection, which is used to operate the integrated microswitch
T直接焊接在壓力單元上的金屬隔膜把壓力轉換為適當的偏斜,從而操縱集成的微開關。Steel frame with welding joint easily occur brittle collapse because of having a low ductility at joints. then, a semi - rigid connected steel frame has large the energy absorption capacity which can resist dynamic loads and the using steel qualities of bracing system and joints are small. so adopting a semi - rigid jointed steel frame is economical and stable
採用焊接剛性節點的鋼框架因節點延性較差容易發生脆性破壞,而半剛接鋼框架因節點具有較強的耗能能力可以抵抗一定的地震荷載,同時還可以減少斜撐的數量及節點用鋼量,這使得半剛接鋼框架成為一種經濟、可靠的選擇。分享友人