斜面型 的英文怎麼說

中文拼音 [xiémiànxíng]
斜面型 英文
plagiohedral
  • 斜 : 形容詞（跟平面或直線既不平行也不垂直的） oblique; slanting; skew; bevel; diagonal; askew; inclined; tilted
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  1. Stability of rock slopes is generally controlled by the structure of rock masses, especially the soft structure surfaces. analysis of rock mass structures is a key to establish geological models and numerical simulation and a foundation to assess the stability of rock slopes. the weak structure surfaces are mainly bedding planes, faults, joints, schistosity plane and contact zones of intrusive bodies. since they are different in genesis and scale, the rock masses are different in features and mechanical intensities. based on the combination of rock structure bodies, 15 basic modes of deformation and failure of rock slope are systematically summarized. the deformation and failure of rock masses actually result from the recombination and rearrangement of these rock bodies. there are 11 types of rock mass structures and various deformation and failure of bank slopes are present in the reservoir area of the three gorge project

    巖體結構，特別是軟弱結構面對基巖斜坡變形與破壞具有顯著的控製作用，巖體結構模式分析是建立斜坡地質模型和數學模型的關鍵和評價斜坡穩定性的基礎。巖層層面斷裂構造節理裂隙片理與劈理以及侵入體和圍巖的接觸帶等是控制基巖斜坡穩定的軟弱結構面，這些成因不同大小不一的結構面將巖體分割成性質各異力學強度不均的各種巖體結構體，構成了15種基巖斜坡變形破壞的巖體結構基本模式。不同結構體的重新組合與排列是斜坡失穩的內在原因。
  2. Sxm11p straight line beveling machine is the latest develop new style of beveling machine from suntech. it specialty adopt beveling wheel, it can whole progress and can lifting intergrally, it compare to traditional front beam or back beam s lifting, it have more pithiness structure. more better stability, higher grinding precision s characteristic. at present this technique was apply country patent. this machine have high automatizationg, set the grinding paramenter into the interface of the human - machine, the machine can automatic to adjust, realize the glass fine grinding, polishing can be automatic processing in one time

    Sxm11p直線斜邊機是億海公司最新開發研製的新型直線斜邊機，它的特點是採用了斜邊磨頭，即可整體進給，又可整體升降的新技術，與傳統的前梁或後梁升降技術相比，具有結構更簡單，穩定性更好，磨削精度更高的特點，目前該技術已申請國家專利，該機自動化程度高，只要在人機界面上設定有關的磨削參數，機器便可自動進行調整，實現對玻璃精磨拋光等的一次性自動加工。
  3. The corbel ' s dimension should be ascertained as the manipulative condition of diagonal section. the amount of longitudinal reinforcement be ascertained on the basis of the flexure model, is obtained according to static for balance condition, the calculative expression of the load is obtained. and in terms of the design method in ultimate state the maximum load

    我國規范對于牛腿的設計規定，牛腿尺寸的確定以斜截面抗裂作為控制條件，縱筋用量的確定以彎壓破壞模型為基礎，根據靜力平衡條件得到承載力的計算公式，按照極限狀態設計方法計算得到，箍筋用量則按照構造要求確定。
  4. As one kind of key equipment in piping work of large - scale turbo - generator set in power plant, the machine is especially applicable to various welding bevels, flat end and angle of outer & inner diameter of ascending pipe, elbow pipe, bend, flange and etc., which greatly meets demands in pipe processing of construction site and manufacturers

    本機床是電站大型汽輪發電機組的管道施工的關鍵設備，對直管、彎管、彎頭、法蘭等管體的各種型式焊接坡口，端平面，內外徑過緩斜度及直口，能滿足施工現場和製造廠家對各種管件的加工要求。
  5. For hoods with shutters in four sides, the results show : 1 ) the hoods positively placed boards are called hoods used for venting airflow ; hoods negatively placed boards are called hoods used for leading airflow ; 2 ) among the hoods used for venting airflow, the most effective hoods should have positive declining angle value of 30, the ratio 4 of areas between the four windward faces and the gular section ( fy / fj = 4 ), the value of b range from 70 mm to 120 mm and the value of b / h range from 0. 5 to 0. 6 ; 3 ) the most effective hoods should have negative declining angle value of 60, the ratio 4 of areas between the four windward faces and the gular section ( fy / fj = 4 ), the value of b range from 100 mm to 170 mm ( the optimum value is 120 mm ) and the value of b / h range from 1. 4 to 2. 2 ( the optimum value is 2. 0 )

    對於四面設百葉型風帽，計算表明: l ）正裝傾斜擋板的百葉型風帽可認為是排風型風帽，倒裝擋板傾斜的百葉型風帽可認為是進風型風帽; 2 ）排風型風帽中，擋板正裝30 」 、風帽四個迎風面的有效面積fy和風管凈斷面積fj的比值（ fy腸）為4 、擋板寬度b在70inln到120inln之間、板間距比值隴在0 . 5到0 . 6的百葉型風帽排風效果最好; 3 ）進風型風帽中，擋板倒裝裝60 「 、風帽四個迎風面的有效面積和風管凈斷面積的比值（ fy例）為4 、擋板寬度b在100咖到170mm之間（ 120mm為最佳） 、板間距比值隴在1 . 4到2 . 0的進風型風帽（ b爪= 2 . 0為最佳）的百葉型風帽進效果最好。
  6. Standard test method for monitoring ground movement using probe - type inclinometers

    使用探針型傾斜儀檢測地面運動的標準試驗方法
  7. Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece

    將液體火箭發動機燃燒室的冷卻通道設計為斜航線（等傾角螺旋線）槽形，可以大幅度改善燃燒室的冷卻性能.斜航線冷卻槽的槽寬尺寸較小而槽深尺寸較大，所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點，提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜，手工編制數控加工程序難度大.為了解決數控加工程序的編制問題，研究了斜航線的數學模型，開發了自動編程軟體系統.使用該系統，可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大，加工難度大，是斜航線冷卻通道加工的最典型工件.經過理論分析和實際切削實驗，研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術，已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用，驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功，對其他相似類型零件的加工亦具有參考意義
  8. A two - dimensional plain strain finite element model of infinite plate is developed to investigate the ultrasonic wave propagation and scattering on three kinds of cracks : parallel to the surface, 450 oblique angle to the surface, and quarter - circle

    摘要建立了無限長板的具有吸收邊界的二維平面應變有限元模型，在研究了脈沖超聲波在無限長板中傳播的基礎上，對板中平行於表面的裂紋、與表面成45的斜裂紋和四分之一圓周弧形裂紋三種情況的脈沖超聲波散射進行了重點研究。
  9. Upn. iron and steel products. inclined face flange sections. dimensions

    鋼鐵產品.斜面凸緣型鋼
  10. D claration abandons itself to the slender transparency of its bevelled glass bottle

    斜面造型的玻璃香水瓶，晶瑩透明、修長勻稱。
  11. In this paper, to counter a flexible beam undergoing large overall motion impacting a fixed slope surface under the effects of grativity, the normal contact model is established based on the hertz theory and non - linear damping term, the tangential contact model is developed by adopting linear tangential contact stiffness to consider the effects of friction force during impact process, and the consistent linear dynamic model including impact is derived by using mode assumption method and lagrangin equation

    針對在重力場下作大范圍回轉運動的柔性梁與一固定斜面發生斜碰撞的情況，根據hertz接觸理論和非線性阻尼項建立法向碰撞接觸模型。引入線性切線接觸剛度建立切向碰撞接觸模型，以考慮接觸過程中由於切向相對速度的換向作用引起的摩擦力的變化。利用假設模態法和lagrangian方程建立系統含碰撞過程的一致線性化的動力學模型。
  12. We own a variety of advanced shoes equipment including : horizontal roughing platform, vertical polishing platform, sole plane automatic roughing machine, high - pressure embossing machine, automatic sole slotting machine, high - pressure changing color machine, high - pressure sole attaching machine, multi - function automatic sole roughing and chaneling machine and over 20 kinds of complete equipment for making shoes

    擁有：各款橫式磨臺、立式磨臺、鞋底斜面打粗機、大底平面自動打粗機、多功能大底自動開槽機、大底銑槽機、大底折邊機、大底烙印機、大底改色機、壓底機等鞋材設備及製鞋全套設備20多種品種機型。
  13. Applied on opening of medium to heavy cartons, double corrugated paper cartons. it has a super high speed of untying, suitable for automation procedure, also suitable for incline opening

    用於中等至重型紙箱，雙層瓦楞紙箱的撕口，適用於工業自動化工序，具極高的解卷速率，同樣試用於斜面撕口。
  14. In some makes of engine the helically splined coupling is not used and the angular displacement of the shafts is effected by centrifugally actuated devices of the swinging link or inclined plane type

    在一些發動機的製造中，並不使用螺旋式花鍵套管，通過搖桿或斜面型的偏心操縱裝置，曲軸相位角起到同樣作用
  15. The outcome suggest that, firstly, the change of light transmission with the continuous change of parameters is periodic ; secondly, as far as the degree of effect is concerned, the light transmission of air - spaced prisms is much more sensitive to the change of the parameters than that of the glue spaced ones ; thirdly, as to the prisms glued with the same dielectric, the effect of prisms whose optical axis parallels to the glued layer is intense than those whose optical axis parallels to the plane determines by the normal of incident face and that of the cut face

    研究認為，激光偏光棱鏡的光強透射比隨各參量的連續變化都呈現出一定的周期性；各參量對空氣隙型偏光棱鏡的影響要比對膠合型棱鏡的影響大的多；同種介質膠合的棱鏡，各參量對光軸平行於切割斜面的設計類型比光軸平行於切割面的法線和入射端面的法線所組成的平面的設計類型的影響要大。
  16. The purpose of the work is to create a new kind of sensor that mainly function is to measure the angle of the inclined plane

    研究的目的是初步製作一個新型的傳感器，主要的功能是測量斜面的傾斜角。
  17. To model the flexible impact system, finite element theory and mode method were respectively used to establish the dynamic equation of the rotating flexible beam, then impact models were built using constraint equation and hertz contact theory, they were differential / algebraic equation and complicated nonlinear equation respectively

    對于柔性撞擊系統的建模問題，分別採用有限元思想和模態法建立了作回轉運動的柔性梁動力學模型，然後又分別利用約束方程和hertz接觸定律給出了其與固定斜面發生接觸的撞擊模型，指出它們的動力學方程分別為微分代數混合方程及復雜的非線性動力學方程。
  18. Square taper washers for i - sections

    工型梁用方形斜面墊圈
  19. The calculating mold consisted of shell, pyramidal neck of shell with varied thickness, flange of ring with definite thickness for analytic solution is set up for the strength calculation and the design of the structure dimension of shell flange and pyramidal neck. this theoretic solution is compared with the results of finite element analysis and stress - strain measurement and is verified to be right

    為設計計算烘缸法蘭及錐頸的強度與結構尺寸要求，建立以簡體、具有斜面的變厚度圓柱殼的錐頸及具有一定厚度圓環的法蘭環為解析解的計算模型，進行應力求解，將該理論解與有限元分析及應力應變實測結果進行分析對比，驗證該解結果的正確性。
  20. Eight cut eight side dut diamon

    一般多面型，八傾斜面琢型
分享友人
分享到 Line

分享到臉書